Agora Models OPTIMUS PRIME Pack 01 Manual
ASSEMBLING THE HEAD – PART 1
ASSEMBLING THE HEAD – PART 2
ASSEMBLING THE HEAD – PART 3
ASSEMBLING THE HEAD – PART 4
ASSEMBLING THE HEAD – PART 5
ASSEMBLING THE CHEST
TESTING THE ELECTRONICS
Pack 01
BUILD INSTRUCTIONS
TRANSFORMERS and HASBRO and all related trademarks and logos are trademarks of Hasbro, Inc. ©2023 Hasbro.
AGORAMODELS 2OPTIMUS PRIME
Please keep ALL unused screws as they may be required in a later stage.
Please make sure you don’t mix up the screws. They look quite similar, but the threads do vary
slightly. Using the wrong screws may damage the parts.
When securing parts together using multiple screws, fit each screw loosely to ensure all the
parts are correctly aligned before gently tightening them firmly, but not overtight, in the order
in which you placed them.
The screwdriver can be magnetized by stroking it with a magnet (fridge magnet, etc.) enabling
it to hold the screws and make assembly easier.
If a screw is tight going into a metal part, do not force it as you may shear the head off. Remove
it and put a tiny smear of Vaseline, soap or light oil on the thread. That will lubricate it and make
it easier to drive home.
Some parts will require a little glue for assembly. Please apply glue sparingly and use a cocktail
stick so that you don’t use too much nor apply the glue too heavily. We recommend superglue
gel or Extra Thin Liquid modeling glue. Where possible, parts should be test-fitted in place
before gluing.
Look out for the glue symbol and apply glue to the red area indicated in the picture.
During the course of this build, you will receive many pieces that you will assemble immediately
– following the instructions in the corresponding stage – and other pieces that you should store
in the tray supplied, for use in future assembly stages.
Always protect the paint finish on components by placing a cutting mat, sheet of white paper
or soft cloth on your work surface.
Left and Right! When building your Optimus Prime, the left or right hand side refers to each
side as viewed by Optimus Prime. Optimus Prime’s left arm is on the viewer’s right.
WARNING: Some parts are assembled using magnets. These magnets can cause serious injury
if they are swallowed. Keep away from children. If you suspect a magnet has been swallowed,
seek medical help straight away.
Advice from the experts
!
!
AGORAMODELS 3OPTIMUS PRIME
Pack 1 : Building the Head & Chest
AGORAMODELS 4OPTIMUS PRIME
Pack 1 Parts
TRAY 1
Screwdriver
TR-1-01
TR-1-11
TR-1-39
TR-1-40
PWM 2x6mm x10
TR-1-12
TR-1-03
TR-1-17
TR-1-20
TR-1-26-1
TR-1-18
TR-1-27
TR-1-16
TR-1-15
TR-1-19
TR-1-58
TR-1-52
TR-1-53
TR-1-08
TR-1-29
TR-1-28
TR-1-21
TR-1-26-2
TR-1-50
TR-1-51
TR-1-22
TR-1-30 TR-1-25
TR-1-24
TR-1-02
TR-1-14 x2
TR-1-23
AGORAMODELS 5OPTIMUS PRIME
Pack 1 Parts
TRAY 2
TR-1-05
TR-1-07
TR-1-10
TR-1-41
TR-1-06
TR-1-09
TR-1-04 TR-1-13
TR-1-45 TR-1-66/67
TR-1-42
TR-1-61
TR-1-60
TR-1-44
TR-1-59
TR-1-43
TR-1-55 x2 TR-1-54 x2
TR-1-34 x4
TR-1-33 x4
PWB 2x6mm x26
AGORAMODELS 6OPTIMUS PRIME
Pack 1 Parts
TR-1-47
TR-1-63 x4
TR-1-56 TR-1-57
TR-1-46 x4
TR-1-36
TR-1-35
TR-1-48 TR-1-62
TR-1-64
x4
TR-1-49
TR-1-37
TR-1-38
TRAY 3
AGORAMODELS 7OPTIMUS PRIME
Assembling the Head – Part 1
TR-1-40
TR-1-39
TR-1-01
TR-1-11
TR-1-12
Glue TR-1-40 as shown in
red in the image above
right before pushing into
place on TR-1-39.
Push TR-1-39 into place on
TR-1-01
Glue parts TR-1-11 and TR-1-12 as shown in red, above
right.
Push TR-1-11 and TR-1-12 onto TR-1-01.
The image on the right shows how your assembly
should look. This will be referred to as assembly ‘A’.
A
1
1a
TR-1-39
2
2a
TR-1-01
STEP 1
STEP 2
AGORAMODELS 8OPTIMUS PRIME
Assembling the Head – Part 1
ATR-1-03
2x PWM
Push assembly Aonto TR-1-03 and fix with
2x PWM screws.
Your completed assembly, shown in the image on
the right, will be referred to as assembly B.
B
3
3a
STEP 3
AGORAMODELS 9OPTIMUS PRIME
Assembling the Head – Part 2
TR-1-20
TR-1-21
TR-1-26-1 C
TR-1-17
TR-1-18
C
Place TR-1-21 on
TR-1-26-1, then place
TR-1-20 onto TR-1-26-1.
The assembly you have
created will be referred to
as assembly C.
Place assembly Cin
between TR-1-17 and
TR-1-18 as shown.
2x PWB
D
1
2
3
3a
Secure the parts together
using 2 x PWB screws.
This assembly will be
referred to as assembly D,
shown in 3a, right.
STEP 1
STEP 2
STEP 3
AGORAMODELS 10 OPTIMUS PRIME
Assembling the Head – Part 3
TR-1-16
TR-1-58
Push TR-1-58 and TR-1-16 together as shown.
Glue the areas shown in red, then push TR-1-16
onto TR-1-19.
This assembly will be referred to as E.
TR-1-19
E
TR-1-52 TR-1-53
ETR-1-15
Push TR-1-52 and TR-1-53
onto E, then push TR-1-15
onto Eas shown.
E
4
4a
5
5a
TR-1-16
STEP 4
STEP 5
Tabla de contenidos
Otros manuales de Juguete de Agora Models
Agora Models
Agora Models JAGUAR E-TYPE Manual
Agora Models
Agora Models FERRARI 312 T4 Manual de usuario
Agora Models
Agora Models Hachette Mitsubishi A6MZERO FIGHTER Manual
Agora Models
Agora Models Mitsubishi A6M ZERO Fighter Manual
Agora Models
Agora Models Lamborghini MIURA Manual
Agora Models
Agora Models CORVETTE STING RAY 1963-Z06/N03 Manual
Agora Models
Agora Models Mitsubishi A6M ZERO Fighter Manual
Agora Models
Agora Models OPTIMUS PRIME Pack 02 Manual
Agora Models
Agora Models LONDON TRANSPORT ROUTEMASTER RM 857 Manual
Agora Models
Agora Models Bismarck Manual
Agora Models
Agora Models ALIEN Manual
Agora Models
Agora Models OPTIMUS PRIME Manual
Agora Models
Agora Models Mitsubishi A6M ZERO Fighter Manual
Agora Models
Agora Models FERRARI 312 T4 Manual de usuario
Agora Models
Agora Models ALIEN Pack 03 Manual
Agora Models
Agora Models Mitsubishi A6M ZERO Fighter Manual
Agora Models
Agora Models Bismarck 06 Manual
Agora Models
Agora Models FERRARI 312 T4 Manual de usuario
Agora Models
Agora Models Bismarck 08 Manual
Agora Models
Agora Models Hachette Mitsubishi A6MZERO FIGHTER Manual
