Agilent Technologies U8001A Manual

Agilent Technologies

Agilent

U8001A/U8002A

Single Output

DC Power Supplies

User’s and Service Guide

II U8001A/U8002A User’s and Service Guide

Notices

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Agilent

Technologies, Inc. as governed by United

States and international copyright laws.

Manual Part Number

U8001-90001

Edition

First Edition, May 22, 2008

Printed in Malaysia

Agilent Technologies, Inc.

3501 Stevens Creek Blvd.

Santa Clara, CA 95052 USA

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connec-

tion with the furnishing, use, or per-

formance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

The hardware and/or software described in

this document are furnished under a license

and may be used or copied only in accor-

dance with the terms of such license.

Restricted Rights Legend

U.S. Government Restricted Rights. Soft-

ware and technical data rights granted to

the federal government include only those

rights customarily provided to end user cus-

tomers. Agilent provides this customary

commercial license in Software and techni-

cal data pursuant to FAR 12.211 (Technical

Data) and 12.212 (Computer Software) and,

for the Department of Defense, DFARS

252.227-7015 (Technical Data - Commercial

Items) and DFARS 227.7202-3 (Rights in

Commercial Computer Software or Com-

puter Software Documentation).

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood and

met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tions are fully understood and

met.

Microsoft ®is a U.S. registered trademark

of Microsoft Corporation.

U8001A/U8002A User’s and Service Guide III

Safety Symbols

The following symbols on the instrument and in the documentation

indicate precautions which must be taken to maintain safe operation of

the instrument.

Direct current Off (supply)

Alternating current On (supply)

Both direct and alternating

current

Equipment protected throughout

by double insulation or reinforced

insulation.

Three-phase alternating current Caution, risk of electric shock.

Earth (ground) terminal Caution, risk of danger (refer to

this manual for specific Warning

or Caution information.

Protective conductor terminal Caution, hot surface.

Frame or chassis terminal Out position of a bi-stable push

control.

Equipotentiality In position of a bi-stable push

control.

IV U8001A/U8002A User’s and Service Guide

General Safety Information

The following general safety precautions must be observed during all

phases of operation, service and repair of this instrument. Failure to

comply with these precautions or specific warnings elsewhere in this

manual violates safety standards of design, manufacture and intended use

of the instrument. Agilent Technologies assumes no liability for

customer’s failure to comply with these requirements.

WARNING

• Do not use the device if it appears damaged or defective.

• Observe all markings on the device before connecting any wiring to the

device.

• Do not operate the device in the presence of flammable gases or fumes.

• Do not install substitute parts or perform any unauthorized modification to

the device.

• Use only the power adapter provided by the manufacturer to avoid any

unexpected hazards.

CAUTION

• Use the device with the cables provided.

• Repair or service that this not covered in this manual should only be

performed by qualified personnels.

U8001A/U8002A User’s and Service Guide V

Environment Conditions

This instrument is designed for indoor use in an installation category II,

pollution degree 2 area. Table 1 shows general environment requirements.

Table 1 Environment Requirements

Environment Conditions Requirements

Operating Temperature 0 °C to 40 °C (for full rated output)

40 °C to 55 °C (for derated output)

Operating Relative Humidity (max) Up to 95%

Storage Temperature –20 °C to 70 °C

Altitude Up to 2000 m

CAUTION

The Agilent U8001A/U8002A single output DC power supplies comply

with the following safety and EMC requirements:

• IEC 61326:2002 / EN 61326:1997+A1:1998+A3:2003

• CISPR 11:1990 / EN 55011:1990

• Canada: ICES-001:2004

• Australia / New Zealand: AS/NZS CISPR11:2004

• IEC 61010-1:2001 / EN 61010-1:2001 (2nd Edition)

• Canada: CAN/CSA-C22.2 No. 61010-1-04

• USA: ANSI/UL 61010-1:2004

VI U8001A/U8002A User’s and Service Guide

Regulatory Markings

The CE mark is a registered trademark of the European

Community. This CE mark shows that the product complies

with all the relevant European Legal Directives.

ICES/NMB-001 indicates that this ISM device complies with

Canadian ICES-001.

The CSA mark is a registered trademark of the Canadian

Standards Association. A CSA mark indicates that the product

is certified for Canadian markets, to the applicable Canadian

standards.

The C-tick mark is a registered trademark of the Spectrum

Management Agency of Australia. This signifies compliance

with the Australia EMC Framework regulations under the

terms of the Radio Communication Act of 1992.

This instrument complies with the WEEE Directive

(2002/96/EC) marking requirement. This affixed product label

indicates that you must not discard this electrical/electronic

product in domestic household waste.

U8001A/U8002A User’s and Service Guide VII

Waste Electrical and Electronic Equipment (WEEE) Directive

2002/96/EC

This instrument complies with the WEEE Directive (2002/96/EC) marking

requirement. This affixed product label indicates that you must not discard

this electrical/electronic product in domestic household waste.

Product Category:

With reference to the equipment types in the WEEE directive Annex 1, this

instrument is classified as a “Monitoring and Control Instrument” product.

The affixed product label is shown as below:

Do not dispose in domestic household waste

To return this unwanted instrument, contact your nearest Agilent office, or

visit:

www.agilent.com/environment/product

for more information.

VIII U8001A/U8002A User’s and Service Guide

DECLARATION OF CONFORMITY

According to EN ISO/IEC 17050-1:2004

Generic example

Manufacturer’s Name: Agilent Technologies Microwave Products (M) Sdn. Bhd

Manufacturer’s Address: Bayan Lepas Free Industrial Zone,

11900, Bayan Lepas, Penang, Malaysia

Declares under sole responsibility that the product as originally delivered

Product Name: Single Output DC Power Supplies

Models Number: U8001A, U8002A

Product Options: This declaration covers all options of the above product(s)

complies with the essential requirements of the following applicable European Directives, and

carries the CE marking accordingly:

Low Voltage Directive (2006/95/EC)

EMC Directive (2004/108/EC)

and conforms with the following product standards:

EMC Standard

StandardStandard

Standard

Limit

LimitLimit

Limit

IEC 61326:2002 / EN 61326:1997+A1:1998+A2:2001+A3:2003

CISPR 11:1990 / EN55011:1990 Class A Group 1

IEC 61000-4-2:1995 / EN 61000-4-2:1995 4 kV CD, 8 kV AD

IEC 61000-4-3:1995 / EN 61000-4-3:1996 3 V/m, 80-1000 MHz

IEC 61000-4-4:1995 / EN 61000-4-4:1995 0.5 kV signal lines, 1 kV power lines

IEC 61000-4-5:1995 / EN 61000-4-5:1995 0.5 kV line-line, 1 kV line-ground

IEC 61000-4-6:1996 / EN 61000-4-6:1996 3 V, 0.15-80 MHz

IEC 61000-4-11:1994 / EN 61000-4-11:1994 1 cycle / 100%

Canada: ICES-001:2004

Australia/New Zealand: AS/NZS CISPR11:2004

The product was tested in a typical configuration with Agilent Technologies test systems.

Safety

IEC 61010-1:2001 / EN 61010-1:2001

Canada: CAN/CSA-C22.2 No. 61010-1-04

USA: ANSI/UL 61010-1:2004

206349

This DoC applies to above-listed products placed on the EU market after:

26-May-2008

Date

Tay Eng Su

Quality Manager

For further information, please contact your local Agilent Technologies sales office, agent or distributor,

or Agilent Technologies Deutschland GmbH, Herrenberger Straße 130, 71034 Böblingen, Germany.

Template: A5971-5302-2, Rev. E U8001A DoC Revision 1.0

U8001A/U8002A User’s and Service Guide IX

Product Regulations

Performance Criteria

IEC 61326-1:2002 / EN 61326-1:1997+A1:1998+A2:2001+A3:2003

CISPR 11:1990 / EN 55011:1990

– Group 1 Class A

IEC 61000-4-2:1995 / EN 61000-4-2:1995

(ESD 4kV CD, 8kV AD) A

IEC 61000-4-3:1995 / EN 61000-4-3:1996

(3V/m, 80% AM) A

IEC 61000-4-4:1995 / EN 61000-4-4:1995

(EFT 0.5kV line-line, 1kV line-earth) A

IEC 61000-4-5:1995 / EN 61000-4-5:1995

(Surge 0.5kV line-line, 1kV line-earth) A

IEC 61000-4-6:1996 / EN 61000-4-6:1996

(3V, 0.15~80 MHz, 80% AM, power line) A

IEC 61000-4-11:1994 / EN 61000-4-11:1994

(Dips 1 cycle, 100%) A

Canada: ICES-001:2004

Australia/New Zealand: AS/NZS CISPR11:2004

EMC

IEC 61010-1:2001 / EN 61010-1:2001

Canada: CAN/CSA-C22.2 No. 61010-1-04

USA: ANSI/UL 61010-1:2004

Safety

Additional Information:

The product herewith complies with the essential requirements of the Low Voltage Directive 2006/95/EC and the

EMC Directive 2004/108/EC and carries the CE Marking accordingly (European Union).

Performance Criteria:

A Pass - Normal operation, no effect.

B Pass - Temporary degradation, self recoverable.

C Pass - Temporary degradation, operator intervention required.

D Fail - Not recoverable, component damage.

N/A – Not applicable

Notes:

Regulatory Information for Canada

ICES/NMB-001:2004

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est confomre à la norme NMB-001 du Canada.

Regulatory Information for Australia/New Zealand

This ISM device complies with Australian/New Zealand AS/NZS CISPR11:2004

X U8001A/U8002A User’s and Service Guide

In This Guide…

This guide provides step- by- step set up and configuration

instructions that get you familiarized with the operations of the

Agilent U8001A/U8002A single output DC power supplies. This

guide also contains service information and troubleshooting

guidelines that help to resolve your problems during startup

configurations.

1 Quick Start

Chapter 1 provides preliminary checkout, output checkout, line

voltage conversion, and instruction to rack- mount for the

U8001A/U8002A single output DC power supplies.

2 General Information

Chapter 2 provides general description of the instrument, front

and rear panel overview, display annunciators, and installation

guidelines for the U8001A/U8002A single output DC power

supplies.

3 Operations and Features

Chapter 3 provides detailed description of the operations and

features for the U8001A/U8002A single output DC power

supplies.

4 Specifications and Characteristics

Chapter 4 lists the power supply’s performance specifications

and the supplemental characteristics of the equipment.

5 Service Guide

Chapter 5 contains service information for the U8001A/U8002A

single output DC power supplies, including warranty

information, general diassemble, verification steps to

troubleshoot the connectivity and functionality, detailed

calibration procedures for your power supply, related

documentation, and Agilent contacts.

Otros manuales para U8001A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Agilent Technologies

Agilent Technologies

Agilent Technologies U8030A Series Manual de usuario

Agilent Technologies

Agilent Technologies 66311A Manual de usuario

Agilent Technologies

Agilent Technologies N8900 series Manual de usuario

Agilent Technologies

Agilent Technologies N5700 Series Manual de usuario

Agilent Technologies

Agilent Technologies E4356A Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies N5769A Guía de inicio rápido

Agilent Technologies

Agilent Technologies 66 A Series Manual de usuario

Agilent Technologies

Agilent Technologies N6751A Manual de usuario

Agilent Technologies

Agilent Technologies E3631A Manual de usuario

Agilent Technologies

Agilent Technologies E3632A Manual de usuario

Agilent Technologies

Agilent Technologies N8700 Manual de usuario

Agilent Technologies

Agilent Technologies E3632A Manual de usuario

Agilent Technologies

Agilent Technologies 6224B Manual de usuario

Agilent Technologies

Agilent Technologies E3632A Manual de usuario

Agilent Technologies

Agilent Technologies 66312A Manual de usuario

Agilent Technologies

Agilent Technologies 66309B/D Manual de usuario

Agilent Technologies

Agilent Technologies E3634A Manual de usuario

Agilent Technologies

Agilent Technologies E3620A Manual de servicio

Agilent Technologies

Agilent Technologies 6214A Manual de usuario

Agilent Technologies

Agilent Technologies 6010A Manual de usuario

Agilent Technologies

Agilent Technologies Series N6700 Manual de usuario

Agilent Technologies

Agilent Technologies E3640A Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Agilent Technologies

Agilent Technologies E3620A Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario

Elmdene

Elmdene G1380xN-y-s Series Manual de usuario

DTS

DTS Megashock 5 Manual de usuario