Agilent Technologies 6631B Manual de usuario

USER’S GUIDE

Dynamic Measurement DC Source

Agilent Model 66332A

System DC Power Supply

Agilent Model 6631B, 6632B, 6633B, 6634B

Agilent Part No. 5962-8196

Microfiche Part No. 5962-8197

Printed in USA: August 2000

Warranty Information

CERTIFICATION

Agilent Technologies certifies that this product met its published specifications at time of shipment from the factory.

Agilent Technologies further certifies that its calibration measurements are traceable to the United States National

Bureau of Standards, to the extent allowed by the Bureau’s calibration facility, and to the calibration facilities of other

International Standards Organization members.

WARRANTY

This Agilent Technologies hardware product is warranted against defects in material and workmanship for a period

of three years from date of delivery. Agilent software and firmware products, which are designated by Agilent for use

with a hardware product and when properly installed on that hardware product, are warranted not to fail to execute

their programming instructions due to defects in material and workmanship for a period of 90 days from date of

delivery. During the warranty period Agilent Technologies will, at its option, either repair or replace products which

prove to be defective. Agilent does not warrant that the operation for the software firmware, or hardware shall be

uninterrupted or error free.

For warranty service, with the exception of warranty options, this product must be returned to a service facility

designated by Agilent. Customer shall prepay shipping charges by (and shall pay all duty and taxes) for products

returned to Agilent for warranty service. Except for products returned to Customer from another country, Agilent shall

pay for return of products to Customer.

Warranty services outside the country of initial purchase are included in Agilent’s product price, only if Customer

pays Agilent international prices (defined as destination local currency price, or U.S. or Geneva Export price).

If Agilent is unable, within a reasonable time to repair or replace any product to condition as warranted, the

Customer shall be entitled to a refund of the purchase price upon return of the product to Agilent.

LIMITATION OF WARRANTY

The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the

Customer, Customer-supplied software or interfacing, unauthorized modification or misuse, operation outside of the

environmental specifications for the product, or improper site preparation and maintenance. NO OTHER

WARRANTY IS EXPRESSED OR IMPLIED. AGILENT SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

EXCLUSIVE REMEDIES

THE REMEDIES PROVIDED HEREIN ARE THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES. AGILENT

SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.

ASSISTANCE

The above statements apply only to the standard product warranty. Warranty options, extended support contacts,

product maintenance agreements and customer assistance agreements are also available. Contact your nearest

Agilent Technologies Sales and Service office for further information on Agilent’s full line of Support Programs.

Safety Summary

The

ollowin

eneral sa

recautions must be observed durin

all

hases o

eration o

this instrument.

Failure to com

with these

recautions or with s

eci

ic warnin

s elsewhere in this manual violates sa

standards o

desi

n, manu

acture, and intended use o

the instrument. A

ilent Technolo

ies assumes no liabilit

or the customer’s

ailure to com

with these re

uirements.

GENERAL

This product is a Safety Class 1 instrument (provided with a protective earth terminal). The protective features of

this product may be impaired if it is used in a manner not specified in the operation instructions.

Any LEDs used in this product are Class 1 LEDs as per IEC 825-1.

ENVIRONMENTAL CONDITIONS

This instrument is intended for indoor use in an installation category II, pollution degree 2 environment. It is

designed to operate at a maximum relative humidity of 95% and at altitudes of up to 2000 meters. Refer to the

specifications tables for the ac mains voltage requirements and ambient operating temperature range.

BEFORE APPLYING POWER

Verify that the product is set to match the available line voltage, the correct fuse is installed, and all safety

precautions are taken. Note the instrument’s external markings described under "Safety Symbols".

GROUND THE INSTRUMENT

To minimize shock hazard, the instrument chassis and cover must be connected to an electrical ground. The

instrument must be connected to the ac power mains through a grounded power cable, with the ground wire firmly

connected to an electrical ground (safety ground) at the power outlet. Any interruption of the protective (grounding)

conductor or disconnection of the protective earth terminal will cause a potential shock hazard that could result in

personal injury.

ATTENTION: Un circuit de terre continu est essentiel en vue du fonctionnement sécuritaire de l’appareil.

Ne jamais mettre l'appareil en marche lorsque le conducteur de mise … la terre est d‚branch‚.

FUSES

Only fuses with the required rated current, voltage, and specified type (normal blow, time delay, etc.) should be

used. Do not use repaired fuses or short-circuited fuseholders. To do so could cause a shock or fire hazard.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the instrument in the presence of flammable gases or fumes.

DO NOT REMOVE THE INSTRUMENT COVER

Operating personnel must not remove instrument covers. Component replacement and internal adjustments must be

made only by qualified service personnel.

Instruments that a

ear dama

ed or de

ective should be made ino

erative and secured a

ainst unintended

eration until the

can be re

aired b

uali

ied service

ersonnel.

This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme à la norme NMB-001 du Canada.

SAFETY SYMBOLS

Direct current

Alternating current

Both direct and alternating current

Three-phase alternating current

Earth (ground) terminal

Protective earth (ground) terminal

Frame or chassis terminal

Terminal is at earth potential. Used for measurement and control circuits designed to be operated

with one terminal at earth potential.

Terminal for Neutral conductor on permanently installed equipment

Terminal for Line conductor on permanently installed equipment

On (supply)

Off (supply)

Standby (supply). Units with this symbol are not completely disconnected from ac mains when

this switch is off. To completely disconnect the unit from ac mains, either disconnect the power

cord or have a qualified electrician install an external switch.

In position of a bi-stable push control

Out position of a bi-stable push control

Caution, risk of electric shock

Caution, hot surface

Caution (refer to accompanying documents)

WARNING The WARNING si

n denotes a hazard. It calls attention to a

rocedure,

ractice, or the like,

which, if not correctl

erformed or adhered to, could result in

ersonal in

. Do not

roceed

ond a WARNING si

n until the indicated conditions are full

understood and met.

Caution The CAUTION si

n denotes a hazard. It calls attention to an o

eratin

rocedure, or the like,

which, if not correctl

erformed or adhered to, could result in dama

e to or destruction of

art

or all of the

roduct. Do not

roceed be

ond a CAUTION si

n until the indicated conditions are

full

understood and met.

DECLARATION OF CONFORMITY

According to ISO/IEC Guide 22 and CEN/CENELEC EN 45014

Manufacturer’s Name and Address

Responsible Party Alternate Manufacturing Site

Agilent Technologies, Inc. Agilent Technologies (Malaysia) Sdn. Bhd

550 Clark Drive, Suite 101

Budd Lake, New Jersey 07828

USA

Malaysia Manufacturing

Bayan Lepas Free Industrial Zone, PH III

11900 Penang,

Malaysia

Declares under sole responsibility that the product as originally delivered

Product Names

a) Mobile Communications DC Source

b) System DC Power Supply

Model Numbers

a) 66332A, 66312A, 66311B, 66311D

66309B, 66309D, 66319B, 66319D, 66321B, 66321D

b) 6631B, 6632B, 6633B, 6634B 6611C

6612C, 6613C, 6614C

Product Options

This declaration covers all options and customized products based on

the above products.

Complies with the essential requirements of the Low Voltage Directive 73/23/EEC and the EMC

Directive 89/336/EEC (including 93/68/EEC) and carries the CE Marking accordingly.

EMC Information

ISM Group 1 Class A Emissions

As detailed in

Electromagnetic Compatibility (EMC), Certificate of Conformance Number

CC/TCF/00/030 based on Technical Construction File (TCF) HPNJ8, dated

Apr. 25, 2000

Assessed by:

Celestica Ltd, Appointed Competent Body

Westfields House, West Avenue

Kidsgrove, Stoke-on-Trent

Straffordshire, ST7 1TL

United Kingdom

Safety Information and Conforms to the following safety standards.

IEC 61010-1:2001 / EN 61010-1:2001

Canada: CSA C22.2 No. 1010.1:1992

UL 61010B-1: 2003

This DoC applies to above-listed products placed on the EU market after:

January 1, 2004

Date Bill Darcy/ Regulations Manager

For further information, please contact your local Agilent Technologies sales office, agent or distributor, or

Agilent Technologies Deutschland GmbH, Herrenberger Straβe 130, D71034 Böblingen, Germany

Acoustic Noise Information

Herstellerbescheinigung

Diese Information steht im Zusammenhang mit den Anforderungen der

Maschinenläminformationsverordnung vom 18 Januar 1991.

* Schalldruckpegel Lp <70 dB(A)

* Am Arbeitsplatz

* Normaler Betrieb

* Nach EN 27779 (Typprüfung).

Manufacturer’s Declaration

This statement is provided to comply with the requirements of the German Sound Emission Directive,

from 18 January 1991.

* Sound Pressure Lp <70 dB(A)

* At Operator Position

* Normal Operation

* According to EN 27779 (Type Test).

Printing History

The edition and current revision of this manual are indicated below. Reprints of this manual containing

minor corrections and updates may have the same printing date. Revised editions are identified by a new

printing date. A revised edition incorporates all new or corrected material since the previous printing

date.

Changes to the manual occurring between revisions are covered by change sheets shipped with the

manual. In some cases, the manual change applies only to specific instruments. Instructions provided on

the change sheet will indicate if a particular change applies only to certain instruments.

This document contains proprietary information protected by copyright. All rights are reserved. No part

of this document may be photocopied, reproduced, or translated into another language without the prior

consent of Agilent Technologies. The information contained in this document is subject to change

without notice.

Update 1 __________July, 1999

Update 2 __________January, 2000

Update 3 __________August, 2000

Table of Contents

Warranty Information 2

Safety Summary 3

Acoustic Noise Information 6

Printing History 6

Table of Contents 7

QUICK REFERENCE 9

Agilent 66332A Dynamic Measurement DC Source and

Agilent 6611C-6614C System DC Power Supply 9

The Front Panel - At a Glance 10

Front Panel Number Entry 11

Front Panel Annunciators 12

Immediate Action Keys 12

Front Panel Menus - At a Glance 13

SCPI Programming Commands - At a Glance 14

The Rear Panel - At a Glance 15

GENERAL INFORMATION 17

Document Orientation 17

Safety Considerations 18

Options and Accessories 18

Description 19

Capabilities 19

Front Panel Controls 19

Remote Programming 19

Output Characteristic 20

INSTALLATION 21

Inspection 21

Damage 21

Packaging Material 21

Items Supplied 21

Cleaning 21

Location 22

Bench Operation 22

Rack Mounting 22

Input Connections 23

Connect the Power Cord 23

Output Connections 23

Wire Considerations 23

Current Ratings 23

Voltage Drops 24

Multiple Load Connections 24

Remote Sense Connections 25

Sense Leads 25

Stability 26

OVP Considerations 26

Fast/Normal Operation 27

Inductive Loading 27

Capacitive Loading 27

INH/FLT Connections 28

Controller Connections 30

GPIB Interface 30

RS-232 Interface 30

TURN-ON CHECKOUT 31

Introduction 31

Using the Keypad 31

Checkout Procedure 31

In Case of Trouble 34

Error Messages 34

Line Fuse 34

FRONT PANEL OPERATION 35

Introduction 35

Front Panel Description 35

System Keys 37

Function Keys 38

Immediate Action Keys 38

Scrolling Keys 38

Metering Keys 39

Output Control Keys 40

Entry Keys 41

Examples of Front Panel Programming 42

1 - Setting the Output Voltage and Current 42

2 - Querying and Clearing Output Protection 43

3 - Making Front Panel Measurements 43

4 - Programming the Digital Output Port 45

5 - Programming the Output Relay (option 760 only) 46

6 - Setting the GPIB Address and RS-232 Parameters 46

7 - Saving and Recalling Operating States 47

SPECIFICATIONS 49

Specifications 49

Supplemental Characteristics 49

VERIFICATION AND CALIBRATION 53

Introduction 53

Equipment Required 53

Test Setup 53

Performing the Verification Tests 54

Turn-On Checkout 54

Voltage Programming and Measurement Accuracy 55

Current Programming and Measurement Accuracy 55

Performing the Calibration Procedure 59

Front Panel Calibration Menu 59

Front Panel Calibration 59

Calibration Error Messages 62

Changing the Calibration Password 62

Calibration Over the GPIB 63

ERROR MESSAGES 65

LINE VOLTAGE CONVERSION 69

Open the Unit 69

Configure the Power Transformer 69

Install the Correct Line Fuse 69

Close the Unit 70

INDEX 71

Quick Reference

Agilent 66332A Dynamic Measurement DC Source and

Agilent 6631B/6632B/6633B/6634B System DC Power

Supplies

The Agilent 66332A is a 100 Watt, high performance dc power supply that provides dynamic

measurement and analysis of voltage and current waveforms. It is designed to simplify the testing of

digital cellular and mobile phones. For example, data acquired using its dynamic measurement capability

can be used in determining the battery operating time of digital wireless communications products.

The Agilent 6631B/6632B/6633B/6634B are 100 Watt, high performance dc power supplies with output

current measurement capability in the microampere range. They are well suited for testing portable

battery-powered products.

Additionally, the combination of bench-top and system features in these dc sources provide versatile

solutions for your design and test requirements.

Convenient bench-top features

♦Up to 100 Watts output power

♦Easy to use knob for voltage and current settings

♦Highly visible vacuum-fluorescent front panel display

♦Excellent load and line regulation; low ripple and noise

♦Measurement capability down to microampere levels

♦Current sinking up to the maximum rated output current

♦Instrument state storage

♦Portable case

Flexible system features

♦GPIB (IEEE-488) and RS-232 interfaces are standard

♦SCPI (Standard Commands for Programmable Instruments) compatibility

♦Triggered acquisition of digitized output current and voltage waveforms (Agilent 66332A only)

♦I/O setup easily done from the front panel

1 – Quick Reference

The Front Panel - At a Glance

j14-character display

shows output

measurements and

programmed values.

kAnnunciators

indicate operating

modes and status

conditions.

lRotary control

sets voltage, current,

and menu parameters.

Use and

to set the resolution;

then adjust the value

with the knob.

mOptional front

panel output

connectors.

66XXA Dynamic Measurement DC Source

0-20V / 02A

CV CC Unr Dis OCP Prot Cal Shift Rmt Addr Err SRQ

240 VDC

Max

LINE

Off

SYSTEM FUNCTION ENTRY OUTPUT

Local

Error

Address

Save

Recall

Shift

Input

Meter

Voltage

OCP

Current

Cal

Output

Prot Clear

Protect

Output

on/off

Clear

Entry

Back

space

Enter

1 2 3

56 7 8

nTurns the dc source

on and off.

oSystem keys:

♦return to Local

mode

♦set the GPIB

address

♦set the RS-232

interface

♦display SCPI

error codes

♦save and recall

instrument states.

pFunction keys:

♦enable/disable

output

♦select metering

functions

♦program voltage

and current

♦set and clear

protection

functions

♦and

scroll through the

front panel menu

commands.

qEntry keys:

♦enter values

♦increment or

decrement values

♦and

select front panel

menu parameters.

♦and

select a digit in

the numeric entry

field.

ÊÉ

ËÌ

ô

Otros manuales para 6631B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Agilent Technologies

Agilent Technologies

Agilent Technologies 6541A Manual de usuario

Agilent Technologies

Agilent Technologies 87421A Instrucciones de funcionamiento y seguridad

Agilent Technologies

Agilent Technologies 6201B Manual de usuario

Agilent Technologies

Agilent Technologies E3633A Manual de usuario

Agilent Technologies

Agilent Technologies 66312A Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies 66102A Manual de usuario

Agilent Technologies

Agilent Technologies E364XA Series Manual de usuario

Agilent Technologies

Agilent Technologies 6030A Manual de usuario

Agilent Technologies

Agilent Technologies 6625A Manual de usuario

Agilent Technologies

Agilent Technologies 66309B/D Manual de usuario

Agilent Technologies

Agilent Technologies 6571A Manual de usuario

Agilent Technologies

Agilent Technologies E364XA Series Manual de usuario

Agilent Technologies

Agilent Technologies E3631-90002 Manual de usuario

Agilent Technologies

Agilent Technologies E4356A Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies 6641A Manual de usuario

Agilent Technologies

Agilent Technologies 6443B Manual de servicio

Agilent Technologies

Agilent Technologies 6116A Manual de usuario

Agilent Technologies

Agilent Technologies E3631A Manual de usuario

Agilent Technologies

Agilent Technologies 654xA Series Manual de usuario

Agilent Technologies

Agilent Technologies N5700 Series Manual de usuario

Agilent Technologies

Agilent Technologies E3631A Manual de usuario

Agilent Technologies

Agilent Technologies E3646A/47A Manual de usuario

Agilent Technologies

Agilent Technologies U8030A Series Manual de usuario

Agilent Technologies

Agilent Technologies E3632A Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario

Elmdene

Elmdene G1380xN-y-s Series Manual de usuario

DTS

DTS Megashock 5 Manual de usuario