Agilent Technologies E2650A Manual de usuario

E2650A Ethernet Adapter

Installation Guide

The E2650A installation kit provides hardware and software for installing

an Ethernet Adapter in Infiniium series oscilloscopes.

The Ethernet adapter enables data and setup files transfers and the use

of network printers. The ethernet adapter supports most popular

network operating systems including:

•NovellNetware

• Microsoft

•Banyan

•VINES

•SCOUNIX

•IBM

The ethernet adapter provides 10 Mbps operation and complies with

IEEE 802.3 Ethernet and ISO/IEC 8802-3 Ethernet standards. The

adapter is fully compatible with TCP/IP protocols.

The ethernet adapter card provides two terminations for connection to

the local area network: RJ-45 and BNC. Only one connector may be used

at a time.

This E2650A Installation Kit contains the following items:

Agilent Part Number Description Quantity

1150-2064 Ethernet adapter board 1

Current version of Infiniium software upgrade 1 pouch

8710-1622 Torx Screwdriver (T-15) 1

E2610-68700 AT compatible keyboard 1

E2650-92001 This installation note 1

Installation Guide

ESD Precautions

When using any of the procedures in this installation note you must use

proper ESD precautions. As a minimum you must place the instrument

on a properly grounded ESD mat and wear a properly grounded ESD

wrist strap.

CAUTION Failure to implement proper antistatic measures may result in damage to the

instrument.

Tools Required

The following tools are required for these procedures.

• Torx driver T15 (one is provided with this kit)

• Torque driver, 2.3 Nm (21 in-lbs), Torx T15 drive

Equipment Required

The following equipment is required for these procedures:

• Keyboard (one is provided with this kit)

• Mouse (or similar pointing device)

CAUTION Do not remove or replace any circuit board assemblies in this instrument while

power is applied. The assemblies contain components which may be damaged

if the assembly is removed or replaced while power is connected to the

instrument.

WARNING SHOCK HAZARD! To avoid electrical shock, adhere closely to the following

procedures. Also, after disconnecting the power cable, wait at least three

minutes for the capacitors on the power supply and sweep boards to discharge

before servicing this instrument. Hazardous voltages exist on the inverter for

the display monitor.

Installation Guide

Do You Need this Installation Kit?

This installation kit contains both a hardware and a software upgrade. To

determine if your Infiniium oscilloscope has the LAN card installed:

1With the power off, look at the back panel of the instrument.

2The expansion slot next the GPIB adapter should be blank.

To verify the Infiniium software version:

1Apply power and wait the for the Infiniium main screen to appear.

2Move the mouse pointer to the graphical interface enable button and

click once.

3Move the mouse pointer to the Help menu and click once.

4Choose About Infiniium... from the drop down list and click once.

5Infiniium software upgrade required if the software revision number is

1.12 or lower.

6Click Close.

GPIB Adapter

Empty

Expansion slot

With the mouse pointer on

the right hand button, click

the mouse to enable the

graphical interface

Installation Guide

Prepare the Infiniium

To prepare the Infiniium:

1Turn the instrument off and remove the power cable.

2If not already installed, connect the mouse or other pointing device.

3Connect the keyboard.

4Re-install the power cable

Installation Guide

Installation Procedure

There are four main steps to complete the LAN card installation:

1Upgrade the Infiniium software.

2Install the LAN card.

3Allow the operating system to recognize the plug-n-play LAN card, install the

LAN card drivers, and setup the initial network identification.

4Connect the network to the LAN card and install or modify the network

resources and drivers.

This installation note details steps 1 through 3. Steps 1 through 3 will take

approximately 45 minutes to complete.

Step 4 is outlined but not described in this installation note. To successfully

complete step 4 you will need mechanical connections, network drivers or

software, and information from the network administrator.

Installation Guide

To Upgrade the Infiniium Software

CAUTION Be sure to follow this procedure to install the Infiniium software upgrade. DO

NOT attempt to perform this upgrade using the Windows ‘95 interface.

1Turn on the Infiniium oscilloscope and wait for the main screen to

appear.

2Enable the graphical interface (see page 3).

3On the main menu, select Utilities, then Upgrade Software... from the

drop down list.

4Click the Start Upgrade button in the dialog box that appears.

5Insert software upgrade disk number 1 in the floppy drive.

6Follow the on-screen instructions, inserting additional disks as

prompted.

7When the last disk has been copied, a prompt appears with the

instructions to remove the disk from the floppy drive and cycle power

on the instrument. Click OK, remove the floppy disk and turn off the

Infiniium.

8Turn the Infiniium on. The message “Beginning System Upgrade” will

appear as the system begins extracting and installing the new files.

9When the new system installation is complete, verify the software

version in Help|About Infiniium... (see page 3). The new version should

be 2.0 or higher.

10 Click Close.

Installation Guide

To install the LAN card

Use the following steps to remove the instrument cover and install the LAN

adapter board.

1Disconnect the power cable.

2Disconnect all scope probes and BNC input cables from the front panel.

3Disconnect any other cables, such as mouse, keyboard, printer, or

GPIB cables.

4Remove the two Torx T15 screws securing the side handle.

5Remove the four Torx T15 screws that secure the rear feet

(two in each foot).

6Remove the four Torx T15 screws that secure the cover to the chassis.

7Set the instrument on its side. Carefully slide the cabinet off the frame

by pulling the front panel and the cover away from each other.

8Set the instrument upright. Remove the Torx T15 screw that secures

the last expansion slot cover (the LAN interface board must be installed

in the last slot, next to the GPIB interface board). Remove and discard

the cover. Save the T-15 screw.

Installation Guide

To install the LAN card

9Insert the LAN interface board into the connector. Position the LAN

interface board through the expansion hole in the rear panel and press

down firmly to seat the board in the connector.

CAUTION When installing the board, be careful not to snag the acquisition cable W11.

You may unplug W11 to make installing the LAN interface board easier. Be sure

to reconnect any cables you remove.

10 Install the Torx T15 screw to secure the LAN interface board to the rear

panel.

11 Replace the instrument cover by reversing steps 4 through 7.

Be sure to keep ribbon cables out of the way when replacing the cover,

particularly the flex cable and connector for the AutoProbe assembly at the

bottom front of the oscilloscope.

CAUTION During replacement, tighten the side handle and rear feet screws

to 2.3 Nm (21 in-lbs).

12 Replace the mouse, keyboard, printer, and GPIB cables. Replace the

power cable.

CAUTION DO NOT apply power with the instrument cover removed.

Installation Guide

To Setup the Network Adapter

1Turn on the Infiniium.

A message indicating “New Hardware Found”, followed by the message

“Windows is installing new software for your hardware” will appear.

2Once Windows ‘95 has installed the software, the message “You must

provide computer and workgroup names that will identify this

computer on the network” will appear. Click OK.

3Provide a computer name and workgroup name in the screen that

appears.

Installation Guide

To Setup the Network Adapter

To complete this procedure set the computer name to Infiniium and the

workgroup name to None.

4Once the names are entered, click OK.

5A dialog box will appear asking if you wish to restart the computer.

Click Yes.

6Wait for the computer to restart. A dialog box asking for a user name

and password will appear, click Cancel and the Infiniium application

will start.

Note

If you know the computer name and workgroup where the Infiniium will be used, you

may enter them in this screen.

Tabla de contenidos

Otros manuales de Adaptador de Agilent Technologies

Agilent Technologies

Agilent Technologies 85130C Manual de servicio

Agilent Technologies

Agilent Technologies 281A Manual de servicio

Agilent Technologies

Agilent Technologies 16200A Manual de operación

Agilent Technologies

Agilent Technologies N4011A Manual de usuario

Agilent Technologies

Agilent Technologies 42942A Manual de operación

Agilent Technologies

Agilent Technologies N1022A Manual de usuario

Agilent Technologies

Agilent Technologies G1364-68709 Hoja de especificaciones

Agilent Technologies

Agilent Technologies 85130F Manual de servicio

Agilent Technologies

Agilent Technologies X/P/K281C Manual de servicio

Agilent Technologies

Agilent Technologies 281A/B Manual de servicio

Agilent Technologies

Agilent Technologies U1177A Manual de usuario

Agilent Technologies

Agilent Technologies E6617A Manual de usuario

Agilent Technologies

Agilent Technologies E1403C Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario