AGFEO TFE 2 Manual de usuario
Installation Manual
TFE 2, TFE 4
Door Phone
The door phones have been designed to be connected directly to the SLT (POT) port of a
telephone system. The voltage for the door phone will be supplied by the telephone system. Door
locks and external bells can be operated in addition but would require a bell transformer to
supply voltage to the door phone. Ensure that the voltage for the door lock will be between 8 V ~
and 14V ~ and that the switched current will not be higher than 2 A ~. The door phone has only
be licensed for its intended use. AGFEO GmbH will not be liable for any damage if the door phone
is used other then for its intended use.
The housing of the door phone may not be opened. Unauthorised opening of the unit and
improper repair may be hazardous to other users and will invalidate the warranty.
Plugs which show defects or power supply units with defect housing must not be continued to
use due to the danger of an electric shock. Ensure that such items are immediately replaced
with original parts.
The door phone may only be connected to power supply units which deliver a SELV Voltage or
comply to ETS 300 047. The intended use of the authorised apparatus fulfil this requirement.
Do not let liquids enter the inside of the door phone as there could be the danger of an electric
shock or short circuiting.
DO NOT install the door phone during a thunder storm or connect or disconnect any cable
connections to eliminate the danger of an electric shock.
DO NOT connect any apparatus which are referring to earth on their lines. You must not
connect the a/b wire to earth as permanent damage to the unit may result.
SafetyNotice
3
TFE 2, TFE 4
Tableof Contents
Safety Notice.................................................................................................................................... 2
Introduction ..................................................................................................................................... 4
Supplied Items ................................................................................................................................. 5
Location of Unit ............................................................................................................................... 7
Flush Mounted Fitting ..................................................................................................................... 8
Surface Mounting .......................................................................................................................... 10
Maximum Distance ....................................................................................................................... 11
Connection of Door Phone to the Telephone System ................................................................... 11
Telephone System Configuration ..................................................................................................12
Programming the Door Phone ..................................................................................................... 13
To Start Programming Mode ......................................................................................................... 13
Enter Extension Number of Bell Push ......................................................................................... 13
Door Opener (Remove Restriction) ............................................................................................... 13
Set Timer for Door Opener ............................................................................................................ 13
Ringing Duration to Extension ...................................................................................................... 14
Set Call Duration ........................................................................................................................... 14
Select Door Phone Operation ........................................................................................................ 14
Calibrate Door Phone .................................................................................................................... 14
Microphone Sensitivity Speaker Volume ....................................................................................... 15
Change PIN of Door Phone ........................................................................................................... 15
Resetting the Door Phone to Default ............................................................................................ 15
Connect Additional Door Bells....................................................................................................... 15
Change Operation of 12 V Output .................................................................................................. 16
Technical Data ............................................................................................................................... 16
Confirmation Tones ....................................................................................................................... 16
Declaration of Confirmity for TFE 2 .............................................................................................. 17
Declaration of Confirmity for TFE 4 .............................................................................................. 18
Declaration of Confirmity for Power Supply ................................................................................. 19
4
TFE 2, TFE 4
Introduction
The AGFEO Doorphones may be connected to the analogue extension ports of AGFEO Telephone
Systems if this has been set to ”Door”.
Please contact your Dealer for connections to AGFEO Systems which do not support the
operation mode “Door”.
The AGFEO TFE 2 can be fitted with 1 or 2 bell push buttons. In addition there is a 12 V contact
and a potential free relay contact.
The AGFEO TFE 4 can be fitted with 3 or 4 bell push buttons and offers a 12 V contact.
The bell push button, in which a name plate may be inserted, is illuminated. A bell transformer
is required for the operation of the button illumination, voltage to the door release and the
operation of the potential free contact relay.
The bell transformer is supplied as a Plug In Type Power Supply and is available optionally. (Order
No.6100259)
The door phones are optimised to work with AGFEO Telephone Systems.
5
TFE 2, TFE 4
1 Door Phone with Cover and Assembled Bell
Push Module
(with 2 push buttons for TFE 2 and 4 push
buttons for TFE 4)
1 Flush Mounted Housing
1 Additional Bell Push Module (with 1 button
for TFE 2 and 3 buttons for TFE 4)
1 Surface Mounted Housing
Supplied Items
1 Pack with 2 Wall Plugs
2 Screws 4 x 30
2 Screw Covers
1CableSleeve
2 Allen Screws
4 Fixing Clamps
4 Screws for Fixing Clamps
1 Allen Key
The Door Phones TFE 2 and TFE 4 are suitable for surface or flush mounting. In addition the TFE
2 may be installed upright or horizontally. The bell push module can be turned by 90o .
Fitting instructions
Bell Push
Module Cover Flush Mounted
Housing Surface
Mount Frame
Screw
Bell Push
Module
Cable Plug
Allen Screw
Bell Push
Cover
Name
Plate
(Foil)
6
TFE 2, TFE 4
InstallationOptions
Before the installation of the door phone you may want to decide if you want to fit the module
upright or horizontally. This is only applicable to the modules with one or two bell push buttons.
The module with three or four buttons can only be installed upright.
Various fitting possibilities for the TFE 2
Button1
Button2
Button1
Button2
Button2
Button1
Button1
Button2
Button2
Fitting possibilities with 1 button
Button2
Button1
Button4 Button4
Button2
Button1
Button3
Fitting possibilities with 3 or 4 buttons
7
TFE 2, TFE 4
Locationof Unit
The door phone TFE 2 and TFE 4 have been designed for use outside and are protected from
water splashes (Dampness protection to IP 53, water splashes of an angle of 60º from vertically)
Please select the location of the unit so that there is a minimum distance of 10 cm ( 4 inches )
from the microphone to the nearest wall. Also ensure that the selected installation location is
free of other services, such as mains cable etc.
min. 10 cm
min. 10 cm
8
TFE 2, TFE 4
The wall cut out should fit the measurements of the flush mounted
housing. (Observe minimum distance and location of installation)
Please make sure that there are no mains services buried in the
wall. Measurements for the cut out to be L x H x D approx. 220 x 90
x 50 mm.
Cable Entry
A cable entry slot is available on all sides of the flush mounted
housing. The cable entry locations are pre assigned and can be
brokenout.
Fixing of Flush Mounted Housing
The housing can be fixed with additional fixing clamps and screws
at the four pre assigned points of the housing. The housing must be
flush to the wall as otherwise the cover cannot be fixed. If the wall
is going to be plastered at later time, then the thickness of the
plaster must be observed.
Connection of Door Phone to System
Connect the wires to the supplied clip and connect this to the
printed circuit board. (see Door Phone Installation)
Inserting the Door Phone
Hook the door phone into the top of the housing and at the same
time pressing the unit upwards to the wall until this snaps into
place. Afterwards tighten the two screws with the Allen Key
provided.
Door Phone Calibration and Configuration
Now carry out the calibration, configuration and commissioning. (see Chapters: Tuning and
configuration, also TFE commissioning)
FlushMountedFitting
1
2Allen key
9
TFE 2, TFE 4
LoosenDoorPhonefromFlush
MountedHousing
Unscrew both screws with the Allen Key provided from
underneath the cover.
Remove Door Phone from Flush Mounted Housing
To release the unit use a medium sized screw driver or Allen
Key and press the bottom latch then pull off the door phone with
an upward movement.
2
1Allen Key
Latch
10
TFE 2, TFE 4
Fit the surface mount frame either upright or horizontally as
required. (Observe minimum distance) Before drilling ensure
that there are no life wires or other main services. Fix the
frame using the wall plugs supplied and screw this to the wall
Connection of Door Phone to System
Install cable to the telephone system and door opener. Drill a
9mm hole in the surface frame were required, pull the cable
through the sleeve and connect the wires to the supplied clip
then connect this to the printed circuit board. (see Door Phone
Installation)
Insert Door Phone
Hold door phone over the fixing hooks of the surface mount
frame and then press firmly until you hear it click into place.
Tighten both screws with the Allen Key provided.
Door Phone Calibration and Configuration
Now carry out the calibration, configuration and
commissioning. (see Chapters: Tuning and configuration, also
TFE commissioning)
SurfaceMounting
Deinstallation
Loosen the door phone by unscrewing the two Allen Screws underneath the unit using the Allen
Keyprovided.
Remove Door Phone from Frame
To release the unit use a medium sized screw driver or Allen Key and press the bottom latch
then pull off the door phone with an upward movement.
Otros manuales para TFE 2
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de AGFEO
