AGFA ANAPURNA MV Manual de usuario

ABTechnical Manual

Technical Manual

(

(:ANAPURNA MV

:ANAPURNA MV)

)

AMV-1606-080531 V1.0

Content

1. How to Install ------------------------------

2. Exterior Appearance & Specification------------ 15

3. How to Use & List of Notice in Use -------------

4. Error in Output & Quality of Printing ------------

5. Servo Motor Driver ------------------------ 98

6. Electric Diagram / PCB Description ------------

122

MODEL : ANAPURNA MV

1.How to Install

How to Install I

How to Install I-

-1

The below is important information that should be checked during installation.

1. The recommended work space for printing is 5M*5M.

(Actual Machine size => 3.5M*1.52M*1.6M)

2. The room in which the printer shall be installed should be easy to clean, dust-free space,

Electromagnetic-free space.

Reasonable temperature in 68 ~ 85℉(20~29℃) should be kept. Humidity in 20%~80% as well.

※Requirement for installation

3. This equipment should be installed on horizontal surface in order to get the printing in the best quality.

4. The equipment should be run with single grounding.

5. In case the safety of working space is required, gas ventilation system will be asked, and the

exhaust duct and ventilation fan should be installed

20% to 80%

Non-condensing

68℉to 85℉

(20℃to 29℃)

Humidity

Temperature

How to Install I

How to Install I-

-2

※List of Notice in relocating the printer.

- As shown in below, the equipment should be lifted up at the marked position.

- When forks of lifter are inserted, be aware not to damage (scratch) the equipment !!

- After checking the left & right balance of equipment, the equipment should be lifted up slowly.

( Please attention that it is sensitive device for impact. )

- Please check a relocating route before carrying by Lifter.

1. Dismantle the front and the upper of WOODEN BOX.

(Remove the screw on the Front and Upper with a driver or electric tool.)

2. After dismantling the packing box, the equipment is relocated by Folk Lifter.

How to Install I

How to Install I-

-2

Folks of Folk Lifter

How to Install II

3. After relocating to desire place, should make a machine balance by using high & low controlling

bolts and level checker.

The position of level checker should be based on box beam, connecting bar and side panel (left, right).

4. ANAPURNA MV is a device that needs compressed air.

Air line connected to Air-compressor or installation place should be mounted on right side of

equipment.

-The diameter of Air Inlet Tube is Φ6.

-The pressure of Compressor is 4~8kgf/㎠, Capacity of above 2HP.

(640 kcal/hr,760W) Air production is over 6 LPM.

★The Compressor must be Oil-less product.

★It is recommended that the compressor should be run independently.

5. Besides the standard power grounding, the print in good quality can be obtained

by connecting grounding line to controller panel in the middle of Machine rear side.

How to Install III

6. After connecting with AC-Line and grounding, connect with machine power code

(220V ±10%, Grounding : Less than 5V)

: ANAPURNA MV consists of power part of main body and that of sub-body.

- 1 st circuit breaker (main S/W) : ON / OFF for power source of main body.

- 2 nd Circuit breaker ( main breaker S/W) : ON / OFF for Main Power.

- 3 rd START S/W : Operation of printer.

Warning

After printer installation, please supply the ink in accordance with How

To Install IV. In case of not following the procedure or skip, some

problems related to head block & printing error would happen.

In order for personnel protection in operation of printing, must understand

the printer by studying thoroughly working guide described in the MSDS.

*APPENDIX: MSDS attached.

How to Install IV

How to Install IV-

-1 (HEAD CLEANING & INK SYPPLY)

1 (HEAD CLEANING & INK SYPPLY)

STEP 1. After removing the cap of ink tube in refill connecting part, push

the solution which remains in ink tube into sub ink tank by using tubing pump

including filter.

Be careful that a solution should not be smeared on the

printer while carrying out solution or ink handing work.

If smeared on the printer, its surface will be discolored.

STEP 2. Connect ink supplying tube in refill system with tube connector

of printer.

Make sure that the ink tube and connector of printer are

tightly connected by the NUT in end of supplying tube.

Impact can cause of tubing-out problem.

Warning

How to Install IV

How to Install IV-

-2 (HEAD CLEANING & INK SUPPLY)

2 (HEAD CLEANING & INK SUPPLY)

STEP 3. Fill 500ml of ink in a main refill ink tank.

ÆBe sure to deflate the air from ink filter of refill part and fill with the ink

after being finished automated refill.

ÆIf ink is supplied in the condition that the air in Ink filter is not completely

removed, overflowing from secondary ink tank will take place due to

excess of air quantity.

Ink Outlet

Structure of Sub Ink Tank

Level Sensor

Air inlet

Ink Inlet

Tabla de contenidos

Otros manuales de Impresora de AGFA

AGFA

AGFA Dry 2.4M Manual de usuario

AGFA

AGFA DRYSTAR AXYS Manual de usuario

AGFA

AGFA DRYSTAR AXYS Manual de usuario

AGFA

AGFA Crystal Imager Manual de usuario

AGFA

AGFA Ovation! Manual de usuario

AGFA

AGFA Drystar 5302 Manual de usuario

AGFA

AGFA d-lab.3 Guía

AGFA

AGFA Drystar 5301 XL Manual de usuario

AGFA

AGFA Anapurna H3200i LED Manual de usuario

AGFA

AGFA Drystar 5500 Manual de usuario

AGFA

AGFA Drystar 5300 Manual de usuario

AGFA

AGFA Drystar 5500 Manual de usuario

AGFA

AGFA Dry 2.4M Manual de usuario

AGFA

AGFA Drystar AXYS XL Manual de usuario

AGFA

AGFA DRY 3.4 Manual de usuario

AGFA

AGFA Drystar 5302 Manual de usuario

AGFA

AGFA AP1100 Manual de usuario

AGFA

AGFA Drystar 4500 Manual de usuario

AGFA

AGFA JETSPEED RTR JETI 5024 Manual de usuario

AGFA

AGFA Avalon N Manual de usuario

AGFA

AGFA Crystal-M Imager Manual de usuario

AGFA

AGFA Drystar 5301 Manual de usuario

AGFA

AGFA Drystar 5301 XL Manual de usuario

AGFA

AGFA DRYSTAR AXYS Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario