AG Neovo F-417 Manual de usuario
1
Table of Content
PRECAUTIONS ................................................................................................. 2
INSTALLATION .................................................................................................... 2
POWER CONNECTION ......................................................................................... 2
USING THE TILT ................................................................................................. 2
MAINTENANCE ................................................................................................... 3
TRANSPORTING THE MONITOR ............................................................................. 3
GETTING STARTED ......................................................................................... 4
PACKAGE CONTENTS .......................................................................................... 4
INSTALLING AND REMOVING THE BASE ................................................................. 5
IDENTIFYING PARTS AND CONTROLS ..................................................................... 6
SETUP .............................................................................................................. 7
CUSTOMIZING YOUR MONITOR..................................................................... 9
WORKING WITH OSD GROUPS ........................................................................... 9
TROUBLESHOOTING..................................................................................... 12
ATTENTION...................................................................................................... 12
LCD PANEL DISPLAY TECHNICAL FEATURES AND SPECIFICATIONS... 13
INTERFACE FREQUENCY ................................................................................... 14
REGULATIONS ............................................................................................... 15
FCC COMPLIANCE ........................................................................................... 15
INFORMATION FOR USERS APPLICABLE IN EUROPEAN UNION COUNTRIES................ 16
INFORMATION FOR USERS APPLICABLE IN UNITED STATES OF AMERICA.................. 16
TCO'99.......................................................................................................... 17
2
Precautions
Installation
• Do not cover or block the ventilation ports on the rear of the monitor.
• Do not install the monitor close to heat sources such as radiators or air ducts, or
in a location exposed to direct sunlight, excessive dust, mechanical vibration, or
shock.
Power connection
• Use the correct power cord for your local voltage.
• Use an accessible outlet close to the monitor.
• Do not allow anything to rest on the power cable.
• Disconnect the power cable from the power supply if:
You will not use the monitor for an extended period.
The cable is damaged or frayed.
The monitor has been dropped or the cabinet damaged.
A distinct change in performance indicates a need for servicing.
Using the Tilt
• Use the monitor’s tilt capability to adjust its vertical orientation to an appropriate
position. Grasp the top corners of the monitor with both hands and tilt to the
desired angle.
+30
-5
3
Maintenance
• Clean the cabinet and controls with a soft cloth lightly moistened with a mild
detergent solution. Do not use any abrasive materials or solvents such as alcohol
or benzene.
• Do not rub, touch, or tap the surface of the screen with sharp or abrasive items
such as pens or screwdrivers, as the screen may scratch.
• Do not insert objects or spill liquids into the ventilation ports on the monitor’s rear,
as fire, electric shock, and/or unit failure may result.
Transporting the monitor
When transporting the monitor for repair or shipment, use the original carton and
packing materials.
4
Getting Started
Package contents
Before beginning, ensure that the carton contains the following items:
• Monitor
• Base
• Power cord
• CD-ROM containing Windows®information file
• Quick Guide
5
Installing and Removing the Base
To attach the base to the monitor, do the following:
When you open the packing carton, remove the LCD monitor base, and place it on a
desk or table. Then attach the LCD monitor to the base.
Note: Make sure that the monitor’s base pegs and the base stand are firmly
locked together.
To remove the base, turn the monitor on its side or up-side down, push the pegs to lift
base off monitor.
6
Identifying parts and controls
The center front panel of the monitor carries the control array.
FRONT VIEW
The controls are, from left to right:
AUTO button
Automatically adjusts the picture and performance. The AUTO function
should be used the first time you use the monitor and after changing the
resolution and/or refresh rate of the input signal.
1) It must be pressing the AUTO button over 1 second to execute auto
adjustment.
Note:
2) If the OSD is acting, this key function will same as down button.
LEFT button
Navigates within the display
RIGHT button
Navigates within the display
DOWN button
Activates the OSD and navigates within the display
UP button
Activates the OSD and navigates within the display
LED indicator
Indicates the monitor’s operational mode; green for regular operation, and
amber for power saving mode.
Power switch
Turns the monitor on and off
7
Setup
Follow these directions to correctly set up your monitor.
1. Remove all packing materials and wrapping from the monitor
2. Place the monitor in its desired location. Ensure that there is space around the
monitor, especially the rear area.
3. With the computer turned off, connect the signal cable to the VGA port on your
PC. Make sure connection is secure.
4. With the monitor switched off, connect the power cord to the Monitor AC socket.
5. Connect the plug Pin of power cord to an AC power source.
A
C Power Jack Power Cord
6. Turn on the computer.
7. Press the power switch on the monitor. The display should appear. If no display
appears, check Troubleshooting in this manual.
8. Ensure that your computer display is set at 1024X768 pixels and 60Hz. Press the
AUTO button exceed 1 second. The monitor optimizes the display
automatically.
8
Note: The monitor is compliant with VESA FPMPMI standards and can be wall- or
arm-mounted. Before wall-mounting or arm-mounting, please disassemble
the monitor stand first.
1. Unscrew screws of the hinge bracket
2. Remove the stand from LCD monitor
2
1
3. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded
nuts, as well as four 5 mm access holes in the plastic covering as illustrated
below. These specifications meet the VESA Flat Panel Monitor Physical
Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13
November 1997).
75mm
75mm
75mm x 75mm
Screw Mounting Options
4mm ,0.7
p
itch threaded holes x4
9
Customizing your Monitor
The On Screen Display (OSD) system provides a full range of customizable tools to
optimize your display.
Important: While full customization is available, we strongly recommend using
the AUTO settings, which are preset to fully optimize your monitor’s
performance. Simply presses the AUTO button exceed 1 second
to engage the AUTO settings. It is also recommended that you
execute the AUTO function following any change made to your
display from your computer.
Working with OSD Groups
Press any of the LEFT , or RIGHT buttons to open the OSD window.
OSD Function Menu
To access OSD Main menu, simply press
one of the Function Select control buttons,
and the menu diagram will pop up on the
screen as shown on Fig. 1-1:
Continue pressing the Function Select
buttons (left/right) to scroll through the
entire menu items , then press Adjustment
Control buttons (up/down) to adjust content
of selected item.
Attention Firmware revision may have been updated into a latest version while
the version number shown on all OSD menus in this manual will stay as
Ver. 1.00.
Brightness & Contrast /
• To fine-tune the monitor’s brightness and contrast, select the pertinent item from
the menu.
• Use the UP and DOWN buttons to set the display as desired on the 0-100
scales that appears at the bottom of the window.
Horizontal & Vertical Position /
• To fine-tune the display’s position on the monitor screen, select the pertinent item
from the menu.
• Use the UP and DOWN buttons to set the display as desired on the 0-100
scales that appears at the bottom of the window.
Sharpness
• This function let's you select the images sharpness. Five selections are available.
A smoother setting is more suitable for pictures, while a sharper setting is more
suitable for text.
• Use the UP and DOWN buttons to set the display image sharpness as
desired.
Otros manuales para F-417
3
Tabla de contenidos
Otros manuales de Monitor de AG Neovo
AG Neovo
AG Neovo X-15E Manual de usuario
AG Neovo
AG Neovo SC-2202 Manual de usuario
AG Neovo
AG Neovo X-19E Manual de usuario
AG Neovo
AG Neovo DR-17G Manual de usuario
AG Neovo
AG Neovo RX-42 Manual de usuario
AG Neovo
AG Neovo TBX Series Manual de usuario
AG Neovo
AG Neovo TM-22 Manual de usuario
AG Neovo
AG Neovo SX-17 Manual de usuario
AG Neovo
AG Neovo X-17P Manual de usuario
AG Neovo
AG Neovo 17" LCD Display E-17B Manual de usuario
AG Neovo
AG Neovo RX-22 Manual de usuario
AG Neovo
AG Neovo PM-48 Manual de usuario
AG Neovo
AG Neovo SX-17 Manual de usuario
AG Neovo
AG Neovo P-17 Manual de usuario
AG Neovo
AG Neovo X-22 Manual de usuario
AG Neovo
AG Neovo PN-46D Manual de usuario
AG Neovo
AG Neovo E-17 Manual de usuario
AG Neovo
AG Neovo L-W24 Manual de usuario
AG Neovo
AG Neovo RX-W22 Manual de usuario
AG Neovo
AG Neovo HX-42 Manual de usuario
