Aeronaut Quido Manual de usuario
aero
naut
Order-No. 1303/00
Electric Model Aeroplane
Quido
Quido is a small model that accompanies you wherever you go. The prefabricated parts are mostly balsa and just need to be assembled according to
the step-by-step building instructions.
With the exception of the tail end of the fuselage, which is a carbon tube, and spruce spars Quido is a pure balsa model. The result is a light-weight yet
strong model. A 2S-LiPo and an outrunner with 100 to 150 Watts are recommended to power the Quido. In addtion you´ll need basic 3-channel radio
equipment with two micro servos and a speed controller.
Construction should be according to the step-by-step instructions provided in this manual. All parts can be identified by means of the parts list at the end of
the manual. Always check that parts fit perfectly. Correct, if necessary, before you glue. Give glue sufficient time to dry before you continue with the next
step.
We recommend white glue (if not otherwise noted) for gluing, which offers good strength and low weight. White glue retains a certain degree of elasticity
even after the glue has cured and will stand up to any loads which occur during flying.
Technical Data
Wing span: 1,070 mm
Length: 850 mm
Weight: from 450 g
Wing area: 21.3 dm²
Wing loading: from 21 g/dm²
RC-functions: rudder, elevator, motor control
Required equipment
ŸOutrunner with backplate mount and approx. 150 W
Ÿ20 A ESC
Ÿ2 micro servos, 23×12 mm
Ÿ2S-LiPo, 850 mAh
Ÿcollet prop adaptor (3.2 mm shaft)* Order.-No. 7124/08
Ÿcollet prop adaptor (4.0 mm shaft)* Order-No. 7124/11
Ÿaluminum yoke 38 mm Order-No. 7242/21
ŸCAM Carbon folding prop 8×4“* Order-No. 7234/13
* Compare recommendations with data sheet of motor
We recommend oour aero-pick
modeller´s pins for building.
Order.-No. 7855/02
Tip
The wing spar is a lamination of three spruce spars.
Mark the centre on all three spars and glue spars
together as shown. Secure spars with tape or clamps
until glue has dried completely. Remove any residual
glue and carefully sand surface of spar.
1
Sort ribs according to cross-section of spar and slide
ribs on spar. Do not glue!
Attention: Make sure to place the two centre ribs
29 in the correct position as they will be sheeted
later on!
2
22
24
23
29
30
31
32
Quido is a small model that accompanies you wherever you go. The prefabricated parts are mostly balsa and just need to be assembled according to
the step-by-step building instructions.
With the exception of the tail end of the fuselage, which is a carbon tube, and spruce spars Quido is a pure balsa model. The result is a light-weight yet
strong model. A 2S-LiPo and an outrunner with 100 to 150 Watts are recommended to power the Quido. In addtion you´ll need basic 3-channel radio
equipment with two micro servos and a speed controller.
Construction should be according to the step-by-step instructions provided in this manual. All parts can be identified by means of the parts list at the end of
the manual. Always check that parts fit perfectly. Correct, if necessary, before you glue. Give glue sufficient time to dry before you continue with the next
step.
We recommend white glue (if not otherwise noted) for gluing, which offers good strength and low weight. White glue retains a certain degree of elasticity
even after the glue has cured and will stand up to any loads which occur during flying.
Technical Data
Wing span: 1,070 mm
Length: 850 mm
Weight: from 450 g
Wing area: 21.3 dm²
Wing loading: from 21 g/dm²
RC-functions: rudder, elevator, motor control
Required equipment
ŸOutrunner with backplate mount and approx. 150 W
Ÿ20 A ESC
Ÿ2 micro servos, 23×12 mm
Ÿ2S-LiPo, 850 mAh
Ÿcollet prop adaptor (3.2 mm shaft)* Order.-No. 7124/08
Ÿcollet prop adaptor (4.0 mm shaft)* Order-No. 7124/11
Ÿaluminum yoke 38 mm Order-No. 7242/21
ŸCAM Carbon folding prop 8×4“* Order-No. 7234/13
* Compare recommendations with data sheet of motor
We recommend oour aero-pick
modeller´s pins for building.
Order.-No. 7855/02
Tip
The wing spar is a lamination of three spruce spars.
Mark the centre on all three spars and glue spars
together as shown. Secure spars with tape or clamps
until glue has dried completely. Remove any residual
glue and carefully sand surface of spar.
1
Sort ribs according to cross-section of spar and slide
ribs on spar. Do not glue!
Attention: Make sure to place the two centre ribs
29 in the correct position as they will be sheeted
later on!
2
22
24
23
29
30
31
32
Place spar with ribs on Depron jig and glue ribs to spar. Glue in place upper
wing spars 25 and lower trailing edge sheeting 37.
3
Glue leading edge 27 to the front of ribs and glue in place
balsa gussets: glue front gussets to groove in leading edge
and rear gussets to top of trailing edge sheeting. Glue the
longer gussets 43 to centre ribs and the short gussets 44 to
the outer ribs. Also glue in place upper trailing edge sheeting
37. Cut to length upper centre wing sheeting 36 and glue in
place.
4
Remove centre wing panel from jig and
turn upside down. Cut off tabs with
modeller´s knife or razor saw and glue in
place lower centre wing sheeting 36.
5
Build up the outer wing panels. Insert
ribs 33 to 35 into wing jigs and glue
in place spars 26 and lower trailing
edge sheeting 38.
The sheeting material is a bit oversize
and will be cut off later.
6
25
37
37
27
43
44
36
36
38
26
33
35
34
Place spar with ribs on Depron jig and glue ribs to spar. Glue in place upper
wing spars 25 and lower trailing edge sheeting 37.
3
Glue leading edge 27 to the front of ribs and glue in place
balsa gussets: glue front gussets to groove in leading edge
and rear gussets to top of trailing edge sheeting. Glue the
longer gussets 43 to centre ribs and the short gussets 44 to
the outer ribs. Also glue in place upper trailing edge sheeting
37. Cut to length upper centre wing sheeting 36 and glue in
place.
4
Remove centre wing panel from jig and
turn upside down. Cut off tabs with
modeller´s knife or razor saw and glue in
place lower centre wing sheeting 36.
5
Build up the outer wing panels. Insert
ribs 33 to 35 into wing jigs and glue
in place spars 26 and lower trailing
edge sheeting 38.
The sheeting material is a bit oversize
and will be cut off later.
6
25
37
37
27
43
44
36
36
38
26
33
35
34
Trim off spars and sheeting material at end ribs and
position wing tips 39 at end ribs (do not glue!). Cut
leading edge parts 28 to correct angle and length
and glue to front of ribs. Glue in place plywood
gussets 45 and upper trailing edge sheeting 38.
7
Remove outer wing panels from jigs, cut off
tabs and carefully sand underside of wing
tips. Glue wing tips 39 to outer wing panels
and glue in place balsa triangles 46 which
support the wing tips.
8
Trim off upper trailing edge sheeting
material, then sand leading edges and
wing tips to shape.
9
Ribs with a triangular cross-section are used for
correct dihedral of outer wing panels. Glue one
rib 40 each flush with underside of wing panels
to centre wing panel and to wing tips. Carefully
sand outline of ribs to shape after glue has
dried.
10
39
28
45
38
46
40
Trim off spars and sheeting material at end ribs and
position wing tips 39 at end ribs (do not glue!). Cut
leading edge parts 28 to correct angle and length
and glue to front of ribs. Glue in place plywood
gussets 45 and upper trailing edge sheeting 38.
7
Remove outer wing panels from jigs, cut off
tabs and carefully sand underside of wing
tips. Glue wing tips 39 to outer wing panels
and glue in place balsa triangles 46 which
support the wing tips.
8
Trim off upper trailing edge sheeting
material, then sand leading edges and
wing tips to shape.
9
Ribs with a triangular cross-section are used for
correct dihedral of outer wing panels. Glue one
rib 40 each flush with underside of wing panels
to centre wing panel and to wing tips. Carefully
sand outline of ribs to shape after glue has
dried.
10
39
28
45
38
46
40
Glue outer wing panels to centre wing panel
and secure with clamps or tape.
After a careful sanding the wing is ready to
cover.
11
Glue the 6 formers together as shown and make sure the
apertures and outer contours match perfectly.
12
Cut 5×5 mm balsa stripwood 13 to a length of
210 mm and build up a box structure using the
two central fuselage formers, wing supports 11
and balsa stripwood 13.
Attention: Stripwood ends exactly at the
contact surface of formers 3 and 4 (see graphics
overleaf)!
13
2
2
3
4
5
6
11
13
Glue outer wing panels to centre wing panel
and secure with clamps or tape.
After a careful sanding the wing is ready to
cover.
11
Glue the 6 formers together as shown and make sure the
apertures and outer contours match perfectly.
12
Cut 5×5 mm balsa stripwood 13 to a length of
210 mm and build up a box structure using the
two central fuselage formers, wing supports 11
and balsa stripwood 13.
Attention: Stripwood ends exactly at the
contact surface of formers 3 and 4 (see graphics
overleaf)!
13
2
2
3
4
5
6
11
13
Glue built-up structure to fuselage side 1. Make sure that
contours for wing saddle match perfectly and that rear end
of fuselage side is flush with contact surface of formers 5
and 6. The lower end of the fuselage side should stand
proud of the stripwood by about 2 mm where the lower
fuselage sheeting will be fitted later on.
14
Glue in place left fuselage side and secure
until dry.
15
Cut to length lower fuselage sheeting material 42
from 2 mm balsa and glue in place.
Attention: Sheeting material ends exactly at the
contact surface of formers 3 and 4!
16
1
1
42
42
42
Tabla de contenidos
Otros manuales de Juguete de Aeronaut
Aeronaut
Aeronaut Bellissima Manual de usuario
Aeronaut
Aeronaut Dassault Breguet Rafale C 01 Manual de instrucciones
Aeronaut
Aeronaut Lilienthal 40 RC Manual de usuario
Aeronaut
Aeronaut Airmarine Special Manual de usuario
Aeronaut
Aeronaut LUXX Manual de instrucciones
Aeronaut
Aeronaut Aero-Maxx Manual de instrucciones
Aeronaut
Aeronaut Scarlet Manual de instrucciones
Aeronaut
Aeronaut Rambotator Manual de usuario
Aeronaut
Aeronaut Triple Neo Series Manual de usuario
Aeronaut
Aeronaut Twinspeedy Manual de usuario
Aeronaut
Aeronaut Xenon RC Manual de instrucciones
Aeronaut
Aeronaut Manta A 02 Manual de usuario
Aeronaut
Aeronaut Jonny Manual de usuario
Aeronaut
Aeronaut Mowe 2 Manual de usuario
Aeronaut
Aeronaut Turbo-fan 4000 Hoja de información del producto
Aeronaut
Aeronaut Sukhoi SU 31M Manual de instrucciones
Aeronaut
Aeronaut Fauvel AV-361 RC glider Manual de instrucciones
Aeronaut
Aeronaut 3092/00 Manual de instrucciones
Aeronaut
Aeronaut Foxx Manual de usuario
Aeronaut
Aeronaut Ramboline Manual de usuario
