Aeroflex 3900 Series Manual de usuario

3900 Series

Operation Manual

Digital Radio Test Set

EXPORT CONTROL WARNING: This document contains controlled technology

or technical data under the jurisdiction of the Export Administration

Regulations (EAR), 15 CFR 730-774. It cannot be transferred to any foreign

third party without the specific prior approval of the U.S. Department of

Commerce Bureau of Industry and Security (BIS). Violations of these

regulations are punishable by fine, imprisonment, or both.

Subject to Export Control, see Cover Page for details.

3900 Series

Digital Radio Test Set

Operation Manual

PUBLISHED BY

Aeroflex

transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise

without the prior permission of the publisher.

Original Release Sep 2008

Issue-2 Feb 2009

10200 West York Street/ Wichita, Kansas 67215 U.S.A. / (316) 522-4981 / FAX (316) 524-2623

Subject to Export Control, see Cover Page for details.

Preface

About this Manual

This manual explains how to use Test Sets found in the 3900 Digital Radio Test Set Series. This

Series currently includes the 3901, 3902 and 3920 Models. Unless otherwise indicated, information

in this manual applies to the 3901, 3902 and 3920 Digital Radio Test Sets.

Electromagnetic Compatibility

Double shielded and properly terminated external interface cables must be used with this equipment

when interfacing with the RS-232 and IEEE-488.

For continued EMC compliance, all external cables must be shielded and 3 meters or less in length.

Nomenclature Statement

The 3901, 3902 and 3920 Digital Radio Test Set is the official nomenclature for the test sets

currently included in the 3900 Digital Radio Test Set Series. In this manual, 3900, unit or Test Set,

refers to the 3901, 3902 and 3920 Digital Radio Test Sets unless otherwise indicated.

Some screen shots may reference frequencies above 1 GHz, which are only applicable to the 3902

and to the 3920 with the 2.7 GHz Frequency Range Option (390XOPT058) installed.

Intended Audience

This manual is intended for personnel familiar with radio test systems and associated equipment.

Preface

Subject to Export Control, see Cover Page for details.

THIS PAGE INTENTIONALLY LEFT BLANK.

Subject to Export Control, see Cover Page for details.

iii

Service Upon Receipt of Material

Unpacking

Special design packing material inside the shipping container provides maximum protection for the

Test Set. Avoid damaging the shipping container and packing material when unpacking equipment;

if necessary the shipping container and packing material can be reused to ship the Test Set.

To prevent personal injury or damage to Test Set, Aeroflex recommends two people unpack the

Test Set.

Use the following steps to unpack the Test Set:

STEP PROCEDURE

1. Cut and remove sealing tape on top of shipping container. Open shipping container and

remove top packing mold.

2. Grasp Test Set firmly while restraining shipping container. Lift Test Set and packing material

vertically out of shipping container.

3. Place Test Set and end cap packing on a flat, clean and dry surface.

4. Remove protective plastic bag from Test Set.

5. Place protective plastic bag and end cap packing materials inside shipping container.

6. Store shipping container for possible future use.

Repacking Procedure

Service Upon Receipt

Subject to Export Control, see Cover Page for details.

Checking Unpacked Equipment

Inspect equipment for possible damage incurred during shipment. If Test Set had been damaged,

report the damage to Aeroflex Customer Service.

Review packing slip to verify shipment is complete. Packing slip identifies the following standard

items as well as purchased options. Report all discrepancies to Aeroflex.

Contact:

Aeroflex

Customer Service Dept.

10200 West York Street

Wichita, Kansas 67215

Telephone: (800) 835-2350

FAX: (316) 529-5330

email: americas.service@aeroflex.com

Description Part Number QTY

Test Set Ship Unit 9001-4402-200 (3901)

9001-4402-100 (3902)

9001-4402-800 (3920)

Cover, Lid 1414-4452-900 1

Kit, 390X Power Cords 7001-4444-800 1

Accessory Kit, RTS 7001-4247-400 1

3900 Series Getting Started Manual 1002-4400-8P0 1

3900 Series Operation Manual (CD-ROM) 1002-4400-2C0 1

Subject to Export Control, see Cover Page for details.

Precautions

SAFETY FIRST - TO ALL OPERATIONS PERSONNEL

General Conditions of Use

This product is designed and tested to comply with the requirements of IEC/EN61010-1 ‘Safety

requirements for electrical equipment for measurement, control and laboratory use’ for Class I

portable equipment and is for use in a pollution degree 2 environment. The equipment is designed to

operate from installation supply Category II.

Equipment should be protected from liquids such as spills, leaks, etc. and precipitation such as rain,

snow, etc. When moving the equipment from a cold to hot environment, allow the temperature of the

equipment to stabilize before it is connected to the supply to avoid condensation forming. The

equipment must only be operated within the environmental conditions specified in the performance

data.

This product is not approved for use in hazardous atmospheres or medical applications. If the

equipment is to be used in a safety-related application, such as avionics or military applications, the

suitability of the product must be assessed and approved for use by a competent person.

Refer all servicing of unit to Qualified Technical Personnel. This unit contains no operator

serviceable parts.

Using this equipment in a manner not specified by the accompanying documentation may impair the

safety protection provided by the equipment.

Case, Cover or Panel Removal

Opening the Case Assembly exposes the operator to electrical hazards that may result in electrical

shock or equipment damage. Do not operate this Test Set with the Case Assembly open.

Safety Identification in Technical Manual

This manual uses the following terms to draw attention to possible safety hazards that may exist

when operating or servicing this equipment.

Safety Symbols in Manuals and on Units

Identifies conditions or activities that, if ignored, can result in equipment or

property damage, e.g., Fire.

Identifies conditions or activities that, if ignored, can result in personal injury or

death.

CAUTION: Refer to accompanying documents. (This symbol refers to specific

CAUTIONS represented on the unit and clarified in the text.)

Indicates a Toxic hazard.

Indicates item is static sensitive.

AC TERMINAL: Terminal that may supply or be supplied with AC or alternating

voltage.

Precautions

Subject to Export Control, see Cover Page for details.

SAFETY FIRST - TO ALL OPERATIONS PERSONNEL (cont)

Equipment Grounding Protection

Improper grounding of equipment can result in electrical shock. Refer to Chapter 2, Installation for

information on properly grounding the Test Set.

Use of Probes

Refer to Appendix B, 3900 Platform Specifications for the maximum voltage, current and power

ratings of any connector on the Test Set before connecting it with a probe from a terminal device.

Be sure the terminal device performs within these specifications before using it for measurement, to

prevent electrical shock or damage to the equipment.

Power Cords

Power cords must be in good working condition. Power cords must not be frayed or broken, nor

expose bare wiring when operating this equipment.

Use Recommended Fuses Only

Use only fuses specifically recommended for the equipment at the specified current and voltage

ratings. Refer to Chapter 2, Installation and the 3900 Platform Specifications for information on

fuse requirements and specifications.

Internal Battery

This unit contains a Lithium Ion Battery, serviceable only by a qualified technician.

EMI (Electromagnetic Interference

Signal Generators can be a source of Electromagnetic Interference (EMI) to communication

receivers. Some transmitted signals can cause disruption and interference to communication

service out to a distance of several miles. User of this equipment should scrutinize any operation

that results in radiation of a signal (directly or indirectly) and should take necessary precautions to

avoid potential communication interference problems.

Electrical Hazards (AC supply voltage)

This equipment is provided with a protective grounding lead that conforms with IEC Safety Class I.

To maintain this protection the supply lead must always be connected to the source of supply via a

socket with a grounded contact.

Be aware that the supply filter contains capacitors that may remain charged after the equipment is

disconnected from the supply. Although the stored energy is within the approved safety

requirements, a slight shock may be felt if the plug pins are touched immediately after removal.

Do not remove instrument covers as this may result in personal injury. There are no user-

serviceable parts inside.

Refer all servicing to qualified personnel. See the list of Aeroflex offices on the back of the

manual.

Fuses

Note that the internal supply fuse is in series with the live conductor of the supply lead. If

connection is made to a 2-pin unpolarized supply socket, it is possible for the fuse to become

transposed to the neutral conductor, in which case, parts of the equipment could remain at supply

potential even after the fuse has ruptured.

Precautions

Subject to Export Control, see Cover Page for details.

vii

Definition of Installation Categories (ref IEC 664-1):

Fire Hazard

Make sure that only fuses of the correct rating and type are used for replacement. If an integrally

fused plug is used on the supply lead, ensure that the fuse rating is commensurate with the current

requirements of this equipment.

Refer to Appendix B, 3900 Platform Specifications for power requirements.

Toxic Hazards

Some of the components used in this equipment may include resins and other materials which give

off toxic fumes if incinerated. Take appropriate precautions, therefore, in the disposal of these

items.

Beryllia

Beryllia (beryllium oxide) is used in the construction of some of the components in this equipment.

This material, when in the form of fine dust or vapor and inhaled into the lungs, can cause a

respiratory disease. In its solid form, as used here, it can be handled safely, however, avoid

handling conditions which promote dust formation by surface abrasion.

Use care when removing and disposing of these components. Do not put them in the general

industrial or domestic waste or dispatch them by post. They should be separately and securely

packed and clearly identified to show the nature of the hazard and then disposed of in a safe

manner by an authorized toxic waste contractor.

Beryllium Copper

Some mechanical components within this instrument are manufactured from beryllium copper. This

is an alloy with a beryllium content of approximately 5%. It represents no risk in normal use.

The material should not be machined, welded or subjected to any process where heat is involved.

It must be disposed of as “special waste.”

It must NOT be disposed of by incineration.

CAT I Circuits that are protected by devices limiting transient overvoltages to a low

level, e.g., electronic circuits protected by filters.

CAT II Circuits that are supply circuits for domestic or digital devices that may include

transient overvoltages with an average value, e.g., power supply for household

appliances and portable tools.

CAT III Circuits that are supply circuits for power equipment that may include large

transient overvoltages, e.g., power supply for industrial machines or equipment.

CAT IV Circuits that may include very high transient overvoltages, e.g., supply

distribution from power lines.

Precautions

Subject to Export Control, see Cover Page for details.

viii

Lithium

A Lithium battery is used in this equipment.

Lithium is a toxic substance so the battery should in no circumstances be crushed, incinerated or

disposed of in normal waste.

Do not attempt to recharge this type of battery. Do not short circuit or force discharge since this

might cause the battery to vent, overheat or explode.

Tilt Feature

Do not stack other instruments on top of unit when instrument is in the tilt position.

Input Overload

On the RF N-type connector, the input power should not exceed 125 W (+51 dBm).

On the RF TNC connector, the input power should not exceed 10 mW (+10 dBm).

Static Sensitive Components

This equipment contains components sensitive to damage by Electrostatic Discharge (ESD). All

personnel performing maintenance or calibration procedures should have knowledge of accepted

ESD practices and/or be ESD certified.

To comply with EMC requirements, double shielded cables should be used for making connections

to all input and output connectors.

CAUTION

THIS EQUIPMENT CONTAINS PARTS

SENSITIVE TO DAMAGE

BY ELECTROSTATIC DISCHARGE (ESD)

Otros manuales para 3900 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de prueba de Aeroflex

Aeroflex

Aeroflex PSD60-2R Manual de usuario

Aeroflex

Aeroflex 8800 Series Manual de usuario

Aeroflex

Aeroflex RGS-2000NG Manual de lista de piezas

Aeroflex

Aeroflex GPSG-1000 Instrucciones de instalación y funcionamiento

Aeroflex

Aeroflex IFR 4000 Manual de lista de piezas

Aeroflex

Aeroflex IFR 6000 Manual de usuario

Aeroflex

Aeroflex IFR 4000 Manual de usuario

Aeroflex

Aeroflex 3550 Manual de usuario

Aeroflex

Aeroflex 8800 Series Manual de usuario

Aeroflex

Aeroflex IFR 4000 Manual de usuario

Aeroflex

Aeroflex 3900 Series Manual de usuario

Aeroflex

Aeroflex ATC-5000NG Manual de usuario

Aeroflex

Aeroflex 3500 Manual de usuario

Aeroflex

Aeroflex 3550R Manual de usuario

Aeroflex

Aeroflex ATC-600A-2 Manual de usuario

Aeroflex

Aeroflex 8800 Series Manual de usuario

Aeroflex

Aeroflex IFR 4000 Manual de usuario

Aeroflex

Aeroflex RD-301A Manual de usuario

Aeroflex

Aeroflex 3900 Series Manual del propietario

Aeroflex

Aeroflex ATC-600A-2 Manual de usuario

Aeroflex

Aeroflex ATC-601-2 Manual de usuario

Aeroflex

Aeroflex IFR 6000 Manual de lista de piezas

Aeroflex

Aeroflex IFR 6000 Manual de usuario

Aeroflex

Aeroflex RD-301A Manual de instalación

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario