Aeotec Recessed Door Sensor 7 Manual de usuario

AEOTEC Engineering Specification

Recessed Door Sensor 7

AEOTEC Engineering Specification

Engineering Specification

Recessed Door Sensor 7

Document No.

SPEC-ZW187

Description

This document mainly introduces the new generation AEOTEC Recessed Door Sensor. The content

mainly includes its interfaces, accessories, features, specifications, quick start, and software

function definition.

Recessed Door Sensor 7 is a Z-Wave Plus v2 device with many advantages.

Can be embedded inside t he wooden door or window.

Used to send out notification via Group 1 (Lifeline) when Magnet is away or near.

Used to control other Z-Wave device directly via Group 2.

Support SmartStart, which makes inclusion more convenient.

Support S2, which makes it more secure and reliable.

Written By

Date

Reviewed By

Date

Approved By

Date

AEOTEC Engineering Specification

REVISION RECORD

Version

Date

Brief description of changes

2019.07.24

First revision.

AEOTEC Engineering Specification

Table of Content

1INTERFACES & ACCESSORIES ..........................................................................................................................................1

2FEATURES & SPECIFICATIONS .........................................................................................................................................2

2.1 Structural Characteristics...............................................................................................................................................2

2.2 Hardware Characteristics ..............................................................................................................................................2

2.3 Software Characteristics ................................................................................................................................................2

3PRODUCT QUICK START..................................................................................................................................................4

3.1 Important safety information ........................................................................................................................................4

3.2 Optimally placing the product .......................................................................................................................................4

3.3 How to install the product .............................................................................................................................................5

3.4 How to add the product into Z-Wave network ..............................................................................................................5

3.5 How to remove the product from Z-Wave network .......................................................................................................7

3.6 How to factory reset ......................................................................................................................................................7

AEOTEC Engineering Specification

Page 1

1INTERFACES & ACCESSORIES

Terminology

Description

Action Button

Inside the Z-Wave Button Hole. Used for networking and resetting.

LED

Used for indicating the current state of the product.

Magnet

Change the sensor state via making the Magnet away or near.

AEOTEC Engineering Specification

Page 2

2FEATURES & SPECIFICATIONS

2.1 Structural Characteristics

Parameter

Value

Product Identifier

ZW187

Dimensions

Main Sensor: Φ19.2×64mm Magnet Sensor: Φ22×13mm

Weight

30g

Color

White

Shell Material

ABS

Shell Fire-proof Level

UL94 V-0

Waterproof and Dustproof

Rated IP20 under IEC 60529

Usage

For indoor use. Can be embedded inside the wooden door or window.

Operating Temperature

32~104°F (0~40°C)

Relative Humidity

8%~80%

2.2 Hardware Characteristics

Parameter

Value

Z-Wave Module

ZGM130S1852B014A7

Z-Wave TX Power

Max: 13dBm

Z-Wave Antenna Distance

40m (Indoor) /150m (Outdoor)

Indicator Light Color

Red

Buttons and Connectors

Action Button (x1), Magnet(x1)

Input Voltage

3.0V Lithium battery

Battery Included

Yes. 1pcs battery included.

Battery Required

Yes. 1pcs battery required.

Battery Info

Model: CR2

Capacity: 800mAh

Detachable: Yes

Chargeable: No

Endurance: 2 years

Working Current

30mA

Standby Current

10uA (Inside the Z-Wave network) / 50uA(Outside the Z-wave network)

Maximum Standby

Power Consumption

0.03mW

Built-in Sensors

Reed switch

Safety Certifications

US: FCC/ETL

EU: CE

AU: RCM

2.3 Software Characteristics

Parameter

Value

Wireless Technology

Z-Wave

Certification Type

Z-Wave Plus v2 Certification

Z-Wave SDK Version

7.11.0.GA (7.11)

Z-Wave Library Type

Enhanced 232 Slave

Z-Wave Role Type

ZWAVEPLUS_INFO_REPORT_ROLE_TYPE_SLAVE_SLEEPING_REPORTING (0x06)

Generic Device Type

GENERIC_TYPE_SENSOR_NOTIFICATION (0x07)

Specific Device Type

SPECIFIC_TYPE_NOTIFICATION_SENSOR (0x01)

AEOTEC Engineering Specification

Page 3

Security Class

Non-Security, S0, S2 Unauthenticated, and S2 Authenticated

SmartStart Compatible

Support. After powering on, SmartStart is auto activated if it’s out of the Z-Wave network.

Over The Air (OTA)

Support. Firmware can be updated via RF.

Multi Channel Device

Association

Support. Refer to Section 4.7 Association Group Info.

Factory Reset

Support. Refer to Section 3.6 How to factory reset.

Power-down Memory

Support. All command settings will stay unchanged even power down.

Timed battery report

Support. Refer to Configuration Parameter 101.

Low battery warning

Support. Refer to Configuration Parameter 90.

Sensor State Report

Support. When Magnet is away or near, send out notification via Group 1 .

Control other device

Support. When Magnet is away or near, control other Z -Wave device directly via Group 2.

AEOTEC Engineering Specification

Page 4

3PRODUCT QUICK START

3.1 Important safety information

Please read this Engineering Specification carefully for correct and effective use.

Failure to follow the recommendations set forth by AEOTEC Limited may be dangerous or cause a violation of the law.

The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting

from not following any instruction in this guide or in other materials.

Recessed Door Sensor 7 is intended for indoor use in dry locations only. Do not use in damp, moist, and /or wet

locations. Contains small parts; keep away from children.

3.2 Optimally placing the product

Recessed Door Sensor 7 has been designed to be installed within a door and its surrounding frame. To optimally install

it, please note the following.

Recessed Door Sensor 7 must be installed so that its two parts separate when the door it is installed within is opened.

Typically, the larger part is installed in the door itself, while the smaller part is installed in the surrounding frame. This is

not mandatory, however, and the installation can be reversed provided the drill hole instructions are suitably adapted.

As a magnetic sensor utilising wireless communication, Recessed Door Sensor 7 may not optimally work when mounted

on a metal frame or close to metal objects such as door locks. Test accordingly before mounting Recessed Door Sensor

7 with adhesive tape or screws.

To be installed, Recessed Door Sensor 7 requires a minimum spacing of around 1mm / 0.04inch between the door and

its frame when closed. The gap should be no larger than 12mm / 0.47inch.

When the door is closed and the sensor's two parts are installed, they should align.

Owing to both the magnet and the Z-Wave Plus antenna housed with Recessed Door Sensor 7, the two highlighted

areas in this diagram are generally considered optimal.

AEOTEC Engineering Specification

Page 5

3.3 How to install the product

The following extra things are needed for the installation: screwdriver, 19mm wide drill bit, drill driver, PVA glue, rubber

hammer.

1. Drill a hole 65mm / 2.56inch deep in your door at the selected location with a 19mm / 0.75inch wide drill bit.

2. Drill a hole 15mm / 0.59inch deep in your doorframe at the corresponding location with a 19mm / 0.75inch wide drill

bit.

3. Insert sensor into the hole you drilled in the door. If it requires force to push the sensor, expand the drill hole

accordingly. Secure the sensor with two of the provided screws.

4. Place a small amount of white PVA glue inside of the hole you drilled in the doorframe. Insert the magnet into the

hole. If it requires force to insert, it can typically be tapped into place with a rubber hammer.

3.4 How to add the product into Z-Wave network

The following will step you through connecting the product to your Z-Wave network.

Note: This product supports Security 2 Command Class. While a Security S2 enabled Controller is needed in order to

fully use the security feature. This product can be operated in any Z-Wave network with other Z-Wave certified

devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of

vendor to increase reliability of the network. QR Code and PIN are used for SmartStart inclusion. DSK Code can be

found on packaging. Do not remove or damage them.

1. Press the sensor latch with a slotting screwdriver to remove the lid of the sensor.

2. Squeeze the sides of the sensor casing to alleviate pressure on the chipboard; slide the chipboard out.

AEOTEC Engineering Specification

Page 6

3. Remove the Pull Tab to engage the pre-installed battery. LED will become slow fade-in fade-out Red color for a few

seconds which will indicate that its power is on.

4. Add Recessed Door Sensor 7 to your Z-Wave network;

A. If your Z-Wave gateway supports SmartStart, Recessed Door Sensor 7 is SmartStart enabled allowing you to connect

it to your Z-Wave gateway by scanning your device’s QR Code using your gateway's app. Once scanned, Recessed Door

Sensor 7 will join your Z-Wave network automatically within 10 minutes.

B. If your gateway supports the Z-Wave Device Specific Key (DSK) security protocol, enter the first 5 digits of your

device's DSK into your gateway's interface when prompted.

C. Else, set your Z-Wave gateway into its 'add device' mode. Refer to the gateway's manual if you are unsure of how to

perform this step. Then press Recessed Door Sensor 7's Action Button once, its red LED will flash Red color.

5. When Recessed Door Sensor 7 successfully joins your Z-Wave network its LED will turn solid red for 10 seconds. If LED

becomes slow fade-in fade-out Red color before turning off, it means the device is still unable to join your Z-Wave

network; repeat the above steps and please contact us for further support if needed.

6. Squeeze the sides of the sensor casing lightly again and re-insert the chipboard as it was. Re-attach the lid.

Recessed Door Sensor 7 is now a part of your Z-Wave home control system. You can configure it and its automations via

your Z-Wave system; please refer to your software's user guide for precise instructions.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de Aeotec

Aeotec

Aeotec Smart Switch 7 ZWA023 Manual de usuario

Aeotec

Aeotec Z-Wave MultiSensor 6 Manual de usuario

Aeotec

Aeotec ZWA005 Manual de usuario

Aeotec

Aeotec GP-AEOMPSEU Manual de usuario

Aeotec

Aeotec TriSensor Manual de usuario

Aeotec

Aeotec Z-Wave Multisensor DSB05-ZWEU Manual de usuario

Aeotec

Aeotec AEOEZW112 Manual de usuario

Aeotec

Aeotec ZW162 Manual de usuario

Aeotec

Aeotec Doorbell Gen5 Manual de usuario

Aeotec

Aeotec MULTISENSOR 6 Manual de usuario

Aeotec

Aeotec Siren 6 Manual de usuario

Aeotec

Aeotec MULTISENSOR 6 Manual de usuario

Aeotec

Aeotec AEO ZWA008-C Manual de usuario

Aeotec

Aeotec Door / Window Sensor 7 Manual de usuario

Aeotec

Aeotec Doorbell 6 Manual de usuario

Aeotec

Aeotec MultiSensor Manual de usuario

Aeotec

Aeotec Water Sensor 7 Pro Manual de usuario

Aeotec

Aeotec Button Manual de usuario

Aeotec

Aeotec Water Sensor 7 Pro Manual de usuario

Aeotec

Aeotec MultiSensor 7 Manual de usuario

Aeotec

Aeotec Door / Window Sensor 7 Manual de usuario

Aeotec

Aeotec ZW089 Manual de usuario

Aeotec

Aeotec ZW187 Manual de usuario

Aeotec

Aeotec MULTISENSOR 6 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario