AEG X-SLIM 35 EC Manual de usuario
OPERATION AND
INSTALLATION INSTRUCTIONS
SHOWER
WATER HEATER
MODEL X-SLIM 35 EC / X-SLIM 45 EC
2
3
General information
The chapter Operation is intended
for users and qualied installer.
The chapter Installation is intended
for qualied installer.
Please read carefully
Read these instruction
carefully before using the appliance
and retain them for future reference.
If the appliance is passed on to a third
party please hand these instructions to
the new user.
- This appliance is not
intended for use by persons
(including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be
supervised to ensure that
they do not play with the appliance.
4
1
2
216 mm.
342 mm.
73 mm.
100 mm.
Fig 1
Fig 2
Dimension
Wall Mounting
Fig 3
Fig 4
Cable
Wiring diagram
220-240 VAC. ONLY
Flow SW.
A
B
C
D
E
A - Heating Element
B - X-Slim-PC Front PCB
C - ELCB
D - X-Slim-PC Control
PCB
E - Thermal Cut-Out
3
Installation Instruction for the qualied installer
Fig 5
a
b
d
c
Shower head level must not be higher than the unit.
5
1. Operation and installation
instruction
1.1 Description of the unit.
The X-SLIM is a slim and pressure-
less instantaneous water heater that
gives you the ultimate shower
experience.
The heating of the water is electronically
controlled and the ow is switched
on and o by using the water valve.
Once the ow volume is sucient,
the “Power” light will indicate that
the unit is switched on.
For safety the unit is tted with an
overheating protection device.
1.2 The essentials - in brief
a. Water valve
b. Rotary control for
temperature adjustment
c. “Power” light
d. Shower accessories
Installation Instruction for the user and the qualied installer
6
Fig 6
E
F
E
F
Push
1.3 Important information
The unit must not be put
under pressure. The outlet
of the unit is also used as a vent.
A periodical scale removal is essential
for the function of the shower head.
1.3.1. The unit is equipped with
an ELCB. It is recommended
to test the ELCB once a
month.
Before using this unit, switch on the
electrical supply then press the
Reset Button (E).
How to test :
When the ELCB test button (F) is
pressed the ELCB Reset (E) Button
will drop. When the reset button (E)
is pressed the unit will be ready to
operate again.
Warning !
If the unit does not operate,
even when pressing the Reset
button, contact service center for
a check and repair.
1.3.2. The unit is equipped with a
Double action thermostat.
In case of permanent
thermostat cut o, contact
services center.
Installation Instruction for the user and the qualied installer
Pic 8
Fig 7
17
5
6
7
8
9
10
11
12
13
14
15
16
19
18
20
21
Cover Base
7
1.4 Detailed description
1. Uper xing hole (Fig 1)
2. Lower xing hole (Fig 1)
3. Depth for mounting screw(Fig 2)
4. Connection cable (Fig 3)
5. Double action thermostat
6. Cable entry with seal
7. Terminal block for earth wire
8. ELCB
9. Connector to PCB control
(Base)
10. Reed switch
11. ELCB reset button
12. ELCB test button
13. Cold water connection
14. Hot water connection for
shower hose
15. X-SLIM tank base
16. Tank cap
17.Filter
18.Rubber seal
19. Water Valve
20. Power Light
21. Connector to PCB Control
(Cover)
Installation Instruction for the user and the qualied installer
8
Fig 8
Fig 9
Fig 10
Fig 11
1.5 Installation Instruction
Switch o main breaker
for water heater.
- Determine the position of the
drillholes by installation
template and drill the holes.
- Release cover securing screw.
- Open and remove cover.
- Insert the wall plugs and screw
make sure insertion depth is
correct (Fig 2 number 3).
- Ensure that the ELCB is switched
o.
- Feed the connection cable seal
in the rear wall.
Installation Instruction for the user and the qualied installer
Fig 12 Fig 14
Fig 15
Fig 13
Earth wire L wire
N wire
9
- The unit must be installed with
a circuit breaker
(see recommended circuit
breaker size in technical data
table).
- Guide the unit over the wall
securing screws and slide it
downwards.
- Fit a secure connection cable
ensure dimensions are correct.
The unit must be earthed
properly (see circuit diagram
(Fig 4)).
(See recommended cable size in
technical data table)
Installation Instruction for the user and the qualied installer
10
Fig 16 Fig 18
Fig 19Fig 17
- Straighten the unit and tighten
the screws.
- Connect the electrical supply
from cover into the PCB control.
- Fit the cover and secure with
the screw.
Installation Instruction for the user and the qualied installer
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Calentador de agua de AEG
AEG
AEG MP 8 Manual de usuario
AEG
AEG EWH-basis Manual de usuario
AEG
AEG MTE 350 Manual de instrucciones
AEG
AEG Huz 5 OKO Comfort Manual de usuario
AEG
AEG Huz 5 OKO Comfort Manual de instrucciones
AEG
AEG BMU 60 Manual de usuario
AEG
AEG DDLE OKO TD 18 Manual de instrucciones
AEG
AEG EWH 15 mini Manual de instrucciones
AEG
AEG MTH 350 Manual de instrucciones
AEG
AEG EWH Basis Series Manual de usuario
AEG
AEG DDLE LCD 18 Manual de usuario
AEG
AEG MTH 350 Manual de usuario
AEG
AEG E Guía de inicio rápido
AEG
AEG U5 Manual de instrucciones
AEG
AEG GYB00416DT Manual de usuario
AEG
AEG DDLE Basis 11 Manual de instrucciones
AEG
AEG DDLT PinControl 13 Manual de instrucciones
AEG
AEG DDLE LCD 18 Manual de usuario
AEG
AEG GYB 00816UT Manual de usuario
AEG
AEG DDLE Basis 11 Manual de usuario
