AEG 125 D Suplemento

125 D

ExtractorHood

InstallationandOperatingInstructions

All manuals and user guides at all-guides.com

all-guides.com

Contents

Introduction 3

Extraction mode 3

Recirculation mode 4

Electrical connection for UK 5

Technical details 6

Installation 7

Safety warnings for kitchen unit installer 7

Wall mounting 9

Hood operation 11

Safety warnings for user 12

Maintenance and care 13

Opening the grid 13

Grease filter 13

Carbon filter 14

Changing the light bulb 15

Cleaning 15

Accessories 16

Something not working 17

Service & Spare Parts 18

Printed on recycled paper.

AEG  putting words into action.

All manuals and user guides at all-guides.com

Introduction

Extraction mode

●The hood is supplied as an extractor unit and can also be used as a

filtered function (recirculation) by fitting activated carbon filters

(available as an accessory).

●The unit features two outlet holes, one of which Ais located on the

top of the unit while the other Bis located on the rear.

●To connect up the hose, you should first fit the bayonet-mounting

flange C(Ø 100-120 mm) on the outlet required (if using the top

outlet, fix the flange in place using the screw supplied as shown in

Fig. 1).

Close off the unused hole using the bayonet fitting caps D.

●Important! To use the back hole B, remove switch Ffrom the

top hole.  Fig 2.

All manuals and user guides at all-guides.com

●Move the lever Lto position A Fig. 3.

●When connecting the hood using a telescopic wall pipe,

you should use a non-inflammable outlet hose ABS 120

(120 mm Ø)

E-Nr. 942 118 611 from our range of special accessories.

Recirculation mode

●The air is filtered and recirculated through the front grid.

●Move the lever Lto position F  Fig. 3.

You will need an original KFF activated carbon filter. (See

accessories).

Summer/Winter Hood Conversion

●To avoid excessive heat loss during the winter months, we

recommend that the hood be converted from extraction mode

to recirculation.

●In order to convert the hood, a charcoal filter (available as an

accessory) is required. Follow the instructions for operating the

hood to recycle air.

●When the temperature outdoors becomes more mild (spring),

the filter can be removed and the hood converted once again to

extraction. Please consult the assembly instructions for operating

the hood in extraction mode.

All manuals and user guides at all-guides.com

Electrical connection for the UK

Appliances with 2 wires

WARNING: DOUBLE INSULATED - DO NOT EARTH

The appliance must be connected to fixed wiring with a double

pole switched fused spur outlet with or without pilot lamp.

We strongly recommend the appliance to be connected only by a

qualified electrician who is a member of the NICEIC who will

comply with the IEE and any local regulations.

NOTE:

The terminology DOUBLE POLE means that both the live and the

neutral supplies are switched and disconnected at the same time.

The terminations labelled SUPPLY are for the connection for the

internal house wiring and the terminations labelled LOAD are for the

appliance.

IMPORTANT

The wires of the mains lead supplied with this appliance are

coloured in accordance with the following code:

Blue-Neutral

Brown-Live

As the colours of the flexible cord of this appliance may not

correspond with the coloured markings identifying the termi-

nals in the plug, proceed as follows: The wire which is coloured

brown must be connected to the terminal which is marked

with the letter L or coloured red.

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured black.

LOAD

SUPPLY

LOAD

SUPPLY

DP 13A, 250V

BLUE

(NEUTRAL) BROWN

(LIVE)

FUSE ON

All manuals and user guides at all-guides.com

Technical details

Dimensions

Height x Width x Depth (in cm) 69-113 x 59.9 x 51

Weight

Net: 11,5 kg

Gross: 12,6 kg

Maximum absorbed power: 205 W

Motor absorption 1 x 125 W

Lighting: 2 x 40 W

Length of the cable: 110 cm

Fan powers (speed), speed in compliance with DIN 44971

Extraction mode

1 115 m3/h

2 152 m3/h

3 210 m3/h

Recirculation mode

1 110 m3/h

2 129 m3/h

3 145 m3/h

Flange:100-120 mm Ø

All manuals and user guides at all-guides.com

all-guides.com

Installation

Safety warnings for kitchen unit installer

●When used as an extractor unit, the hood must be fitted with a

100 or120mm diameter hose.

●If the fumes must be forced out through the wall, you must

obtain a MKZ sizable wall exhaust pipe (with external exhaust and

air intake), E-Nr.- 610 899 004 (Ø 120 mm) which is one of our

optional parts.

●When installing the hood, make sure you respect the fol-

lowing minimum distance from the top edge of the cooking

hob/ring surfaces:

Electrical 650 mm

Gas hob 700 mm

Electric cooker 685 mm

Gas cooker 787 mm

●The hood cannot be connected to flues of other appliances that

run on energy sources other than electricity.

●The air outlet must not be connected to chimney flues or com-

bustion gas ducts. The air outlet must under no circumstances be

connected to ventilation ducts for rooms in which fuel-burning

appliances are installed.

●It is advisable to apply for authorization from the relevant

controlling authority when connecting the outlet to an unused

chimney flue or combustion gas duct.

The air outlet installation must comply with the regulations laid

down by the relevant authorities.

●When the unit is used in its extractor version, a sufficiently large

ventilation hole must be provided, with dimensions that are

approximately the same as the outlet hole.

●National and regional building regulations impose a number of

restrictions on using hoods and fuel-burning appliances connected

to a chimney, such as coal or oil room-heaters and gas fires, in

the same room.

All manuals and user guides at all-guides.com

●Regulations on fuel-burning systems specify a maximum

depression of 0.04 bar in such rooms.

●Hoods can only be used safely with appliances connected to a

chimney if the room and/or flat (air/environment combination) is

ventilated from outside using a suitable ventilation hole approxi-

mately 500-600 cm2 to avoid the possibility of a depression

being created during operation of the hood.

If you have any doubts, contact the relevant controlling authority

or building inspectors office.

●Since the rule for rooms with fuel burning appliances is outlet

hole of the same size as the ventilation hole, a hole of 500-600

cm2, which is to say a larger hole, could reduce the performance

of the extractor hood.

●If the hood is used in its filtering function, it will operate simply

and safely in the above conditions without the need for any of the

aforementioned measures.

●When the hood is used in its extractor function, the following

rules must be followed to obtain optimal operation:

 short and straight outlet hose

 keep bends in outlet hose to a minimum

 never install the hoses with an acute angle, they must

always follow a gentle curve only

 keep the hose as large as possible (120 mm Ø min.).

●Failure to observe these basic rules will drastically reduce the

performance and increase the noise levels of the extractor hood.

All manuals and user guides at all-guides.com

Wall mounting

●Fix the drilling template to the wall.

●Make 3 Ø 8mm holes in the wall 2 at points I, 1 as desired at

points L.

●Insert the three Ø 8mm expansion plugs into the wall.

●Insert 2 5x45 screws at points Ibut do not tighten them

completely.

●Adjust the unit so that it is positioned at a right angle to the wall

by turning the two support screws G.

●Fit the hood into holes I, tighten the 2 screws.

●From inside the hood, insert the third 5x45 screw into hole L. 

Fig. 4.

●Measure the height between the upper side of the body of the

cooker hood and the ceiling (fig. 5).

All manuals and user guides at all-guides.com

●Set the chimney according to the measured height and stop its

run with the two fixing screws 2,9x6,5 mm supplied (fig. 6).

●Fix the chimney to the aesthetic top with two screws 2,9x6,5

mm supplied (fig. 7).

●From the inside of the hood, fix the aesthetic top with four screws

M3x6 supplied (Two each side)(fig. 8).

●Fix the upper bracket to the wall, close to the ceiling,

perpendicularly to the outlet hole of the hood with 2 screws

5x45 mm (fig. 8).

●Fix the chimney to the bracket with two screws 2,9x6,5 mm

(fig. 8).

All manuals and user guides at all-guides.com

Otros manuales para 125 D

Tabla de contenidos

Otros manuales de Campana de ventilación de AEG

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

Smeg

Smeg KSEV97X Manual de usuario

Nibe

Nibe S Series Guía del usuario

Caple

Caple CCH100 Manual