Advanced Mxp-007 Manual de usuario

www.advancedco.com

Relay Output Cards

Features

The Mxp-007 and Mxp-008 are internal peripherals for use with the MxPro 4 panels. The units connect

directly to the panel’s motherboard and provide either 2 or 8 individually programmable 1-Amp rated, volt free,

clean contact outputs.

Each output can be individually assigned to an output group to provide full support for the MxPro 4 system’s

DynamiX zoning facilities. In addition, each output has a number of programmable operational parameters

including fail-safe, can-silence, allow walk test and delayed operation.

These features not only aid commissioning and cut down on expensive ancillary hardware but also allow the

system to be easily configured to provide full support for the more complex cause and effect configurations

using standard products.

www.advancedco.com

Specifications & Ordering:

Models, Sales Order Parts:

Mxp-007: 2 Way Relay Output Card

Mxp-007F: 2 Way Relay Output Card fitted within an Mx4100/L, Mx4200, Mx4400 or Mx-4800 control panel

Mxp-008: 8 Way Relay Output Card

Mxp-008F: 8 Way Relay Output Card fitted within an Mx4200, Mx4400 or Mx-4800 control panel

Applications / Limitations:

Ideal for any application where a number of programmable outputs are required at the panel. E.g. Landlord /

Tennant interfaces.

Each output can be assigned to an individual output group and is fully programmable for any output function

allowed within the MxPro configuration program.

Only one 2 Way Relay Output Card can be fitted to an Mx-4100/L control panel.

Only one 2 Way or 8 Way Relay Output Card can be fitted to an Mx-4200 or Mx-4400 control panel.

Up to two 2 Way or 8 Way Relay Output Cards can be fitted to an Mx-4800 control panel.

Compatibility:

The Mxp-007 is fully compatible with the Mx-4100, Mx-4200, Mx-4400 and Mx-4800 Fire Alarm Control Panels.

The Mxp-008 is fully compatible with the Mx-4200, Mx-4400 & Mx-4800 Fire Alarm Control Panels.

Mounting pillars are provided to mount these cards as follows:

Mx-4200, Mx-4400 & Mx-4800 on the panel chassis.

Mx-4100/L on the rear face of the back box.

Item

Specification Details

Mxp-007

Mxp-008

Relay Outputs

2 Volt Free Contacts

(2 x changeover)

8 Volt Free Contacts

(2 x changeover+ 6 x normally open which can

be inverted)

Contact Rating

1 Amp 30V DC/AC max

Power Supply

24V DC (Derived from the panel’s motherboard)

Supply Current

(All relays energised)

17mA maximum

65mA maximum

Dimensions

(H x W x D)

70mm x 105mm x 18mm

As our policy is one of constant product improvement the right is therefore reserved to modify product specifications without prior notice

www.advancedco.com

Table of Contents Page

1INSTALLATION...................................................................................................................................................4

1.1 INSTALLING THE MXP-007 IN THE MX-4100/L.................................................................................................4

1.1.1 Mounting the Card...................................................................................................................................4

1.1.2 Internal Wiring.........................................................................................................................................4

1.2 INSTALLING THE MXP-007 IN THE MX-4200/MX-4400/MX-4800......................................................................4

1.2.1 Mounting the Card...................................................................................................................................4

1.2.2 Internal Wiring.........................................................................................................................................4

1.3 INSTALLING THE MXP-008 IN THE MX-4200/MX-4400/MX-4800......................................................................5

1.3.1 Mounting the Card...................................................................................................................................5

1.3.2 Internal Wiring.........................................................................................................................................5

1.4 EXTERNAL WIRING ........................................................................................................................................5

2PROGRAM THE RELAY OUTPUTS...................................................................................................................6

2.1 MAY SILENCE:...............................................................................................................................................7

2.2 INVERTED OUTPUT: .......................................................................................................................................7

2.3 MAY WALK TEST:..........................................................................................................................................7

2.4 INVESTIGATION:.............................................................................................................................................7

www.advancedco.com

1 Installation

1.1 Installing the Mxp-007 in the Mx-4100/L

1.1.1 Mounting the Card

Mxp-007

Base Card

Cable

M3 Fixing Points (x4)

TB2

TB6

TB1

TB5

PL1

The card mounts on 4 pillars in the rear of the enclosure. See

diagram opposite.

Screw in the four spacers supplied into the threaded inserts in the

back box. Use the four M3 screws supplied to securely affix the

card to the spacers.

1.1.2 Internal Wiring

Use the supplied 4-way single in line ribbon cable to connect the

relay card, via the latched header –PL2, to the 4-way latched

header on the base card.

1.2 Installing the Mxp-007 in the Mx-4200/Mx-4400/Mx-4800

1.2.1 Mounting the Card

Base Card

M3 Fixing

Screws

TB3

Mxp-007

The card mounts on 4 pillars in the top left hand corner of the

control panel chassis adjacent to the Mx4200/Mx 4400 base card.

See diagram opposite.

Use the four M3 screws supplied to securely affix the card to the

chassis.

It is not possible to install the Mxp-007 in this position if either the

Mxp-021 Sounder Splitter or the Mxp-028 Modem is already

installed.

1.2.2 Internal Wiring

Use the supplied 4-way single in line ribbon cable to connect the

relay card, via the latched header –PL2, to the adjacent 4-way

latched header on the base card.

www.advancedco.com

1.3 Installing the Mxp-008 in the Mx-4200/Mx-4400/Mx-4800

1.3.1 Mounting the Card

Base Card

M3 Fixing

Screws

TB3

Mxp-008

The card mounts on 4 pillars in the top left hand corner of the

control panel chassis adjacent to the Mx4200/Mx 4400 base card.

See diagram opposite.

Use the four M3 screws supplied to securely affix the card to the

chassis.

It is not possible to install the Mxp-008 in this position if either the

Mxp-021 Sounder Splitter or the Mxp-028 Modem is already

installed.

1.3.2 Internal Wiring

Use the supplied 10-way single in line ribbon cable to connect the

relay card, via the latched header –PL1, to the adjacent 10-way

latched header on the base card.

1.4 External Wiring

The picture below shows the terminal block

positions for each relay output.

Relay positions 1 and 2 provide NO / NC

changeover contacts. Relay positions 3 –8

provide NO contacts only (Mxp-008 Only).

Install cables suitable for the application and

degree of fire protection required. These circuits

are SELV type.

If additional knockouts are required on the Mx-

4200 or Mx-4400 then use the deeper back box

(Mxm-020) or use the Termination Enclosures

(Mxm-028 or Mxm-029) as appropriate.

RELAY

COM

All electrical wiring installation work should be carried out in

accordance with the code of practice applicable in the

country of installation.

To maintain electrical integrity of the SELV wiring on the

output lines all SELV wiring should be segregated from the

LV mains wiring and be wired using cable with insulation

suitable for the application.

To minimise the effects of EMC interference all data wiring

circuits should be wired with a twisted pair of conductors with

a cross sectional area suitable for the loading conditions.

In areas where cabling may come into contact with high

frequency interference, such as portable radio transceivers

etc. the output wiring cable should be of a twisted pair

construction within an overall screen. The screen should be

terminated to one of the dedicated earth studs available in

the panel (refer to panel manual for positions).

NB: Minimum / Maximum cable size for all connections is

limited to 0.35mm² / 2.5mm² (22-14AWG).

www.advancedco.com

2 Program the Relay Outputs.

Each relay output can be independently programmed in the same way as other outputs on the panel.

On the PC configuration software the outputs are under the “On-board” devices and shown as “Panel O/C-1”

through to “Panel O/C-8”.

O/C-1 and O/C-2 only for the Mxp-007

O/C-1 to O/C-8 for the Mxp-008

By default, the relays are all in the same Output Group, 199, but this can be changed as required. In the example

below, the relays have been assigned to groups 180 to 187. These output groups can be programmed as required.

For a more detailed explanation of assigning output groups refer to PC Net manual, see document reference 680-

021.

The properties that can be assigned to each relay output are depicted in the boxes on the “Point Details” section.

By ticking the appropriate box, the relay will take on those assigned properties.

www.advancedco.com

2.1 May Silence:

If this parameter is ticked, the relay will behave in a similar manner to a sounder circuit output. It will energise as

defined by their “Output Group” setting and de-energise when the “Silence” key is pressed.

2.2 Inverted Output:

If this parameter is ticked, the relay will behave in a manner similar to a “Fault” relay output and will be normally

energised in its quiescent state and de-energised when its “Output Group” setting is activated.

2.3 May Walk Test:

If this parameter is ticked, the relays assigned with this parameter will be allowed to energise when a “Walk Test”

with ring bells option is enabled.

The relay will energise for a short time, along with the bells / sounders, when a walk test alarm is generated.

2.4 Investigation:

If this parameter is ticked, the relay will follow the programmed output stage 1 delay timer and delay its operation

while the cause of the alarm is investigated.

www.advancedco.com

This page is intentionally left blank.

www.advancedco.com

USER NOTES

www.advancedco.com

Advanced Electronics Ltd

Moorland Way, Cramlington, Northumberland, NE23 1WE UK

Tel: +44 (0)1670 707 111 Fax: +44 (0)1670 707 222

Email: sales@advancedco.com Web: www.advancedco.com

Doc Number: 680-028

Revision: 03A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Relé de Advanced

Advanced

Advanced MxPro Series Manual de usuario

Manuales populares de Relé de otras marcas

Shelly

Shelly Pro Series Manual de usuario

GE MVAX 11 Manual de usuario

ABB

ABB RELION REF615R Manual de usuario

Pilz

Pilz PNOZ X10 Manual del propietario

ABB

ABB SPAJ 142 C Manual de lista de piezas

Kemo Electronic

Kemo Electronic B197 Manual de usuario

Seg

Seg MRM3 Manual de usuario

Basler

Basler BE1-700C Manual de usuario

CD Automation

CD Automation REVEX 2PH 280A Manual de usuario

Ruelco

Ruelco 1S04 Manual de usuario

Basler

Basler V3E Z1P B2C1F Manual de usuario

Doepke

Doepke Dupline DSM 2 Manual de usuario

Siemens

Siemens SIRIUS 3RT1966-4D Manual de usuario

GE DGP Manual de usuario

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Manual de usuario

Siemens

Siemens SIPROTEC 4 Manual de usuario

Siemens

Siemens BD2-AK03X/FS Series Manual de usuario

Leuze

Leuze MSI-SR5B Manual de usuario