Advanced AxisAX AX-PENN Manual de usuario

www.advancedco.com

AX-PENN & AX-PENN/ST7

Peripheral Expansion Network Node

Installation & Operation Manual

www.advancedco.com

Table of Contents Page

1INTRODUCTION / OVERVIEW ................................................................................................................................. 3

1.1PRODUCT DESCRIPTION ....................................................................................................................................... 3

2INSTALLATION ......................................................................................................................................................... 4

2.1MOUNTING .......................................................................................................................................................... 4

2.2DIMENSIONS ........................................................................................................................................................ 4

2.3WIRING ............................................................................................................................................................... 5

2.3.124VDC Power Supply ................................................................................................................................... 6

2.3.1.1Power Supply Monitoring ..................................................................................................................................... 6

2.3.1.2Intelligent Power Supply Monitoring .................................................................................................................... 6

2.3.2Ad-NeT-PluS Network Connection ............................................................................................................... 7

2.3.2.1AX-PENN (Class B) Ad-NeT-PluS Network Wiring .............................................................................................. 8

2.3.2.1.1Class B Ad-NeT-PluS Network ....................................................................................................................... 8

2.3.2.2AX-PENN/ST7 (Class X) Ad-NeT-PluS Network Wiring ...................................................................................... 8

2.3.2.2.1Class X Ad-NeT-PluS Network ....................................................................................................................... 9

2.3.3Peripheral Bus (P-BUS) ................................................................................................................................ 9

2.3.3.1Wiring ................................................................................................................................................................ 10

2.3.4Optional AX-DSP Keyboard Display ........................................................................................................... 10

2.3.5USB Port ..................................................................................................................................................... 11

2.3.6RS-232 Port ................................................................................................................................................ 11

3AX-PENN (/ST7) PC-NET PROGRAMMING .......................................................................................................... 12

3.1ADDING AN AX-PENN (/ST7) NETWORK NODE .................................................................................................. 12

3.1.1Panel Details Programming ........................................................................................................................ 13

3.1.2On-Board Programming .............................................................................................................................. 14

3.1.3User Interface Programming ....................................................................................................................... 14

3.1.4Peripheral Bus Programming ...................................................................................................................... 15

3.2UPLOADING, DOWNLOADING AND FIRMWARE FLASHING ...................................................................................... 15

3.2.1Uploading and Downloading Procedure ..................................................................................................... 16

3.2.2Firmware Updating Procedure .................................................................................................................... 16

4AXISAX WIRING GUIDE ........................................................................................................................................... 17

5AX-PENN (/ST7) STATUS LEDS ............................................................................................................................ 20

www.advancedco.com

1 Introduction / Overview

1.1 Product Description

This manual covers the installation and operation of an Axis AX-PENN and AX-PENN/ST7 Peripheral Expansion

Network Node module for use on Advanced Ad-NeT-PluS networks. The AX-PENN is a Class B network interface

module, while the AX-PENN/ST7 is a Class X (A/Style 7) network interface module.

AX-PENN (/ST7) peripheral expansion network node modules provide an on-board Axis AX peripheral bus (PBUS)

allowing for the connection of any Advanced peripheral bus module remotely from the Axis AX fire alarm control panel

(i.e.: switch LED modules, audio amplifier modules, relays, etc.).

Each AX-PENN or AX-PENN/ST7 peripheral expansion network node module can support an optional AX-DSP

graphical keyboard display for localized network monitoring and control.

This equipment is constructed with static sensitive components. Observe anti-static precautions at all

times when handling printed circuit boards. Wear an anti-static ground strap connected to panel

enclosure earth ground.

CAUTION: Before installing or removing any printed circuit boards remove all sources of power (AC and

battery).

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

SENSITIVE DEVICES

www.advancedco.com

2 Installation

2.1 Mounting

The AX-PENN (/ST7) is designed for mounting within any Advanced enclosure. The module mounts wherever an

Advanced peripheral bus module can be mounted. In addition, the module can be mounted to a single aperture plate

for single aperture opening installation (see figure 1 mounting locations).

To ensure EMC immunity to fast transient and surges the AX-PENN (/ST7) must be connected to an earth ground.

Each installation screw of the AX-PENN (/ST7) module provides a ground connection to its associated mounting plate

for eventual earth ground connection via the mounting plate/enclosure.

Failure to tighten screws will defeat the protection circuitry designed to protect the card from damage due to

lightning and static electricity.

2.2 Dimensions

Below are the dimensions of the AX-PENN (/ST7) peripheral expansion network node module.

SCR

OUT

SCR

NETWORK RS485

PERIPHERAL RS485

OUT

PROGRAM

COMMISION

REBOOT

PSU_TX

PSU_RX

HEARTBEAT

USB/232RX

USB/232TX

DISPLAY ONLY

PWR FLT

USB

GNDRXTX

RS232 FEED 1 FEED 2

NET TX

NET RX

NET485

EOL

24V

OUT

24V

OUT

24V

OUT

24V

OUT

FTNET HB

MEM

LOCK

P485 TX

P485 RX

4.5"

2.7"

I/P

Figure 1 - AX-PENN (ST/7) Mounting Locations and Dimensions

www.advancedco.com

2.3 Wiring

The AX-PENN (/ST7) peripheral expansion network node module is designed to be easy to install and wire. Pluggable

terminal blocks are provided for all wiring which can accommodate up to 14 AWG wire. Confirm wiring sizes are

adequate to deliver the required load current and maintain compatibility with the device voltages.

Note: Disconnect all sources of power (AC and battery) before installing components or servicing the module.

All wiring must comply with local, state and authority having jurisdiction requirements, in addition to Article

760 of the National Electrical Code (NEC).

Refer to Axis AX Wiring Guide Section 4.

SCR

OUT

SCR

NETWORK RS485

PERIPHERAL RS485

OUT

PROGRAM

COMMISION

REBOOT

PSU_TX

PSU_RX

HEARTBEAT

USB/232RX

USB/232TX

DISPLAY ONLY

PWR FLT

USB

GNDRXTX

RS232 FEED 1 FEED 2

NET TX

NET RX

NET485

EOL

OUT IN

24V

OUT

24V

OUT

24V

OUT

24V

OUT

FTNET HB

MEM

LOCK

P485 TX

P485 RX

+ -

24VDC

OUT

Class B

PBUS

Class A

PBUS

Return

Ad-NeT-PluS

Network In To Next Network Node or if

Class B Network, EOL Jumper

Optional AX-DSP

Keyboard Display

Power Supply/Charger

Monitoring Input

N/O Contact

I/P

Figure 2 – AX-PENN (/ST7) Input/Output Wiring

www.advancedco.com

2.3.1 24VDC Power Supply

The AX-PENN (/ST7) module must be powered from an ANSI/UL listed 24VDC fire alarm power supply/charger (i.e.

AX-PSU-6). Wire the 24VDC supply to the FEED 1 24V and 0V IN terminals (see figure 3). If utilizing the supply

voltage for other power requirements, wire the 24V and 0V OUT terminals to the other 24VDC device.

2.3.1.1 Power Supply Monitoring

If the AX-PENN (/ST7) is powered from an external listed power supply/charger, the power supply/charger must be

monitored for trouble conditions. To monitor the external power supply/charger, wire the AX-PENN (/ST7) terminals I/P

SW+ and SW- terminals to a “normally open” failsafe trouble contact of the power supply/charge and terminate with the

supplied 3.3K end of line resistor (see figure 4). If monitoring an intelligent internal power supply/charger (i.e. AX-PSU-

6) place the supplied 3.3K end of line resistor across the I/P SW+ and SW- terminals.

2.3.1.2 Intelligent Power Supply Monitoring

If the AX-PENN (/ST7) is powered internally by an Advanced AX-PSU-6 power supply charger, connect the supplied 4

pin connecter to the PL2 plug-in connector on the AX-PSU-6; connect the other end of the supplied 4 pin connector to

the PSU COM (PL3) plug-in connector on the AX-PENN (/ST7) [see figure 5]. In addition, within the PC-NeT

programming tool, under Panel Details, Trouble Notification; program the AX-PENN (/ST7) for intelligent power supply

monitoring by placing a check in the associated box (see figure 6).

PERIPH

DISPLAY ONLY

P485 TX

P485 RX

3.3K

I/P

Figure 3 – AX-PENN (/ST7) 24VDC Wiring

Figure 4 – External Power Supply Monitoring Wiring

www.advancedco.com

2.3.2 Ad-NeT-PluS Network Connection

Based on the installation’s Ad-NeT-PluS network, Class X (A/Style 7) or Class B, the correct AX-PENN (/ST7) module

[AX-PENN (Class B) or AX-PENN/ST7 (Class X)] must be installed.

SCR

OUT

SCR

NETWORK RS485

PERIPHERAL RS485

OUT

PROGRAM

COMMISION

REBOOT

PSU_TX

PSU_RX

HEARTBEAT

USB/232RX

USB/232TX

DISPLAY ONLY

PWR FLT

USB

GNDRXTX

RS232 FEED 1 FEED 2

NET TX

NET RX

NET485

EOL

24V

OUT

24V

OUT

24V

OUT

24V

OUT

FTNET HB

MEM

LOCK

P485 TX

P485 RX

I/P

Figure 6 – Intelligent Power Supply Monitor Programming

Figure 5 – Intelligent Power Supply Wiring

www.advancedco.com

2.3.2.1 AX-PENN (Class B) Ad-NeT-PluS Network Wiring

Wire the Ad-NeT-PluS network, A OUT, B OUT and SCN (shield) from the previous node to the A IN, B IN and SCN

(shield) terminals of the AX-PENN module (see figure 7). Wire the A OUT, B OUT and SCN (shield) of the AX-PENN

module to the next network node. If the AX-PENN module is the last node on the Ad-NeT-PluS network, place the NET

485 EOL (J2) jumper in the IN position (see figure 7).

2.3.2.1.1 Class B Ad-NeT-PluS Network

 32 Network Nodes (requires 150Ω filtering resistor at the beginning and at the end of the network)

 Maximum Overall Cable Length 5000ft

Cable wiring must be minimum twisted shielded pair 18AWG to 20AWG. Connect the shield to the designated shield

terminals only.

The “IN” terminals on the first node and the “OUT” terminals on the last node are not used. Connect an end of line

filtering resistor (150Ω) between A and B on the unused terminal blocks.

2.3.2.2 AX-PENN/ST7 (Class X) Ad-NeT-PluS Network Wiring

Wire the Ad-NeT-PluS network, A OUT, B OUT and SCN (shield) from the previous node to the A IN, B IN and SCN

(shield) terminals of the AX-PENN/ST7 module (see figure 8). Wire the A OUT, B OUT and SCN (shield) of the AX-

PENN/ST7 module to the next network node. If the AX-PENN/ST7 module is the last node on the Ad-NeT-PluS

network wire the A OUT, B OUT and SCN (shield) to the first Ad-NeT-PluS network node, terminals A IN, B IN and

SCN (shield) [see figure 8].

Figure 7 – AX-PENN (Class B) Ad-NeT-PluS Network Wiring

www.advancedco.com

2.3.2.2.1 Class X Ad-NeT-PluS Network

 200 Network Nodes

 Maximum Cable Length between Nodes 5000ft

 Maximum Overall Cable Length 66000ft

Cable wiring must be minimum twisted shielded pair 18AWG to 20AWG. Connect the shield to the designated shield

terminals only.

Wire from the last network node “OUT” terminals back to the first network node “IN” terminals to form a complete loop

“ring”.

2.3.3 Peripheral Bus (P-BUS)

The AX-PENN (/ST7) can support sixteen (16) of each type of Advanced peripheral bus modules. Peripheral bus

modules must be located within 20 feet of the AX-PENN (/ST7) module within the same room. Below is a list of

available peripheral bus modules:

Document

AX-ASW-16 Switch Module with 16 Switches and 48 LEDs 682-020

AX-ACM-6 Fan/Damper Module 682-079

AX-LED16 LED Annunciator Module, 16 Red and 16 Yellow 682-020

AX-LED32R LED Annunciator Module, 32 Red 682-020

AX-LED32Y LED Annunciator Module, 32 Yellow 682-020

AX-I/O-48 16 Switch Input and 48 LED Driver Outputs 682-020

Figure 8– AX-PENN/ST7 (Class X) Ad-NeT-PluS Network Wiring

www.advancedco.com

AV-AMP-80 Audio Amplifier Module 682-032

AX-RL4 Four Relay Output Module 682-026

AX-CZM Conventional Zone Module 682-040S/SA

2.3.3.1 Wiring

Wire the Peripheral RS485 terminals A OUT and B OUT to a peripheral bus module RS485 (PBUS) terminals A and B

(A to A, B to B) [see figure 9]. Place a 150 Ohm filtering end-of-line (EOL) resister on the last peripheral bus module.

Note: Though the AX-PENN (/ST7) can support Class A PBUS (peripheral bus) wiring, this feature is presently

not available, as existing peripheral bus modules do not support Class A communications.

2.3.4 Optional AX-DSP Keyboard Display

The AX-PENN (/ST7) can support a standard Advanced AX-DSP keyboard display, simply wire the keyboard display

cable to the AX serial port on the AX-PENN (/ST7) [see figure 10].

PE RI PHER AL RS4 85

OUT

DISP LAY ONLY

P485 TX

P485 RX

Class B

PBUS

Class A

PBUS

Return

I/P

PE RI PHER AL RS4 85

OUT

DISPLAY ONLY

PW R FLT

ME M

LOCK

P485 TX

P485 RX

Optional AX-DSP

Keyboard Display

I/P

Figure 9– AX-PENN (/ST7) Peripheral Bus Wiring

Figure 10 – AX-PENN (/ST7) Optional Keyboard Display Wiring

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario