Advanced BMW OBDII Manual de usuario

BMW OBDII Key programmer ADVANCED

Now works with K-Line and D-CAN bus

BMW OBD Key programmer ADVANCED is designed to program new original

key or PCF7936 chip.

Key programming takes only 10-15 seconds (for CAS sw. versions before

ISTA-P-41) and only 8-11 minutes for CAS with new firmware (sw. version ISTA-

P-41 and higher).

Newer sw. version CAS (ISTA-P-41 and up) will only take longer time the first

time you program the key. If you ever programmed this car –all next attempts

will be fast within 10 seconds.

Also, the device turns off the factory security alarm (for the time of

programming) and erases the memory of diagnostic faults via OBDII.

The ADVANCED kit also includes the HT Pro device and two HTspy keys for

BMW and MINI Cooper.

Supported models

BMW 1' E88 (11/2006 —10/2013)

BMW 1' E82 (11/2006 —10/2013)

BMW 3' E90 (02/2004 —08/2008)

BMW 3' E90 LCI (07/2007 —12/2011)

BMW 3' E91 (02/2004 —08/2008)

BMW 3' E91 LCI (07/2007 —05/2012)

BMW 3' E92 (05/2005 —02/2010)

BMW 3' E92 LCI (11/2008 —06/2013)

BMW 3' E93 (09/2005 —02/2010)

BMW 3' E93 LCI (11/2008 —10/2013)

BMW 5' E60 (05/2003 —12/2009)

BMW 5' E60 LCI (10/2005 —12/2009)

BMW 5' E61 LCI (11/2005 —05/2010)

BMW 6' E63 (05/2002 —07/2010)

BMW 6' E63 LCI (04/2006 —07/2010)

BMW 6' E64 (09/2002 —07/2010)

BMW 6' E64 LCI

BMW X1 E84

BMW X5 E70

BMW Z4 E89

(04/2006 —07/2010)

(04/2009 —06/2015)

(01/2007 — 12/2013)

(01/2008 —08/2016)

MINI R56 (11/2005 —07/2010)

MINI R56 LCI (04/2009 —11/2013)

MINI Clubman R55 (10/2006 —07/2010)

MINI Clubman R55 LCI (03/2009 —06/2014)

MINI Cabrio R57 (11/2007 —07/2010)

MINI Cabrio R57 LCI (04/2009 —06/2015)

MINI Coupé R58 (01/2011 —05/2015)

MINI Roadster R59 (01/2011 —04/2015)

MINI Countryman R60 (01/2010 —10/2016)

MINI Paceman R61 (03/2012 —09/2016)

Device description

The programmer has two diodes D, K, Ready and a sound buzzer.

LED features:

D LED indicates diagnostic status.

K LED shows the status of the data for key generation.

Ready LED

D- flashesgreen after establishing communication with the car. Light is

always on: green on successful completion, red on failure.

K- green if the device has found all the data for the key. Flashing red if

the data from DDE / DME is not read.

Red light is always on: it is possible to program only the “service key”

Sound signals:

1) Rising sound - from low to high - successful programming

2) Long constant sound - only “Service key” is possible.

Reconnect the OBDII and repeat again.

3) Lowering sound - from high to low - unsuccessful shutdown

4) Short double beep - insert the key into the ignition slot and turn on the ignition.

If the programmer LEDs blink red and a constant beep is heard immediately it

means a programmer malfunction. Mail or call us to arrange the device

repairing.

If your security alarm is off or you do not have security alarm at all then you

do not need to do these operations. You can continue to the key

programming procedures.

Make sure that the option switch is switched to the "Alarm Off" position.

Make sure that the car battery status shows 11 or higher voltage.

Connect the programmer to the car OBDII. (wake up the car’s CAN bus: unlock

the car door with a mechanical key or press the START/STOP button).

The LEDs on the programmer will blink

K – green

D - red

You will hear a beep and the LEDs will stop blinking

within 5-10 seconds. The alarm will turn off.

Don’t try to start a car before programming is complete!

After completion, you will hear a beep and the LEDs will show the device

status (see the device description - LED features).

Errors:

•The programmer LEDs quickly blink red for a long time (more than 20 seconds)

or do not light up at all –car communication error.

•Make sure the car is not in sleep mode (press the car's START/STOP button).

•If the START/STOP button light is on and the device cannot do operations - it is

probably an additional non OEM security system installed.

Alarm disabling

Key programming

The car should not be in sleep mode! The car’s START/STOP button light

should be on,

if not - press START/STOP button or press the central locking button (for the

old E60).

Make sure that the option switch is switched to the "Key Programming"

position.

Make sure that the car battery status shows 11 or higher voltage.

1..Connect the device to the OBDII.

The LEDs will blink:

K–green

D- red or green

Wait for the Ready LED to blink.

On a car with an old CAS version (up to ISTA-P-41) or if the CAS was already

programmed with this device:

the K LED will slowly blink green in 5-10 seconds.

On a car with the new CAS version (ISTA-P-41 and up), when you connect to

this car first time:

Programming will start automatically and it will not be possible to start the car

until its completion! CAS programming takes about 8-11 minutes.

Upon completion of programming, All of the LEDs will turn green.

2. Put the key in the device coil and hold it in this position until the work is completed.

If all of the three LED diodes (D, K and Ready) light up (not blinking) green and you

can hear one beep signal then the key/transponder is programmed.

A) If the D, K and Ready LEDs are light up green and you heard rising beep, the

car is ready to start.

B) If you hear short multiple beeps,insert the just programmed key into the ignition

coil, turn on the ignition/press START/STOP button and wait until programming is

done (it can take from 10 to 60 seconds). Do not disconnect the device until the

procedure is done. Wait until D and K LEDs constantly light up green and you can

hear a rising beep sound.

C) If the LED Dlights up green, Klights up red and you can hear a constant beep it

means that only the “service key” is programmed (read more about Service key

option below).

D) If the LED Dis red + lowering the sound signal an error has occurred (see errors).

Note: The device stores codes of all programmed keys –that’s why you can

reprogram those keys to other vehicles.

You can watch the full process of programming new key here:

https://youtu.be/mHrudo-lnl0

Key programming

               



     

 

  



  

   



. .

   

 

  



   

       



     

+48 517 443 433

+48 22 724 99 96

[email protected]



 

B) If LED Dis red and you can hear alowering beep - it is a CAS error. Repeat

several times starting from step 1 and if the error is repeated, then programming

with thecar is not possible.

C) If the device's LEDsare off for a long time (for longer than 20 seconds) or quickly blink

yellow - there is acommunication error with the car. Make sure the car is not in sleep

mode (Press the car's START/STOP button). If the START/STOP button light is on, the

device operation is not possible (probably there is an additional (after factory) security

system of the car installed).

Errors:

A) If the device LED flashes green / red alternately - writing key error.

Repeat everything from step 1 and if the error has been repeated, replace

the key.

Troubleshooting

Service Key

This key allows you to unlock and lock a car central lock with the remote

control but does not allow starting the engine!

In case if all the data necessary for key programming was not read,the device can

program the key only with the RF function.

If you program spare key ask the customer to start the car with original key, then

open the car with the remote control of the service key and write it again according to

“Key Programming” –it should takes 10-15 seconds.

A service key like any other key can be re-programmed to other cars.

Diagnostic fault codes and steering lock fault

erasing.

Vehicle ignition is On.

Connect the device to the car. LED Don the programmer will turn green + beep.

Errors:

Programmer LED blinks red or does not light - communication error with the car

(probably an additional security system (after factory) of the car is installed).

HTPro / HTspy key

The ADVANCED kit includes HTpro and HTspy keys for BMW and MINI.

With these devices, you are able to ensure that all modules in the car are fully

functional before programming a new key. This will allow you to avoid the situation

that after programming the transponder/key, it turns out that, for example, you need

to replace the CAS module and the programmed transponder in the new key,

unfortunately, must be thrown away. When you use these devices, you can save

information from the new key on your own computer and program another key to the

car in the future without need to have a car.

Tabla de contenidos

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario