Advanced Wireless Communications AWR-CB2100 Manual de usuario

AWR-CB2100 UHF One-way Call box

Operator Manual

Built in Mount

Reset Button

LED

MIcrophone

Activator

Speaker

Reset Button

Battery Drawer

Built-in Mounting

Screw

(3) D-Cell Battery

Battery Drawer

AWR-CB2100 UHF One-way Call box Features:

• 450MHz to 470MHz Frequency Band of Operaon - Analog

• .5W or 2W transmit power level

• Water resistant (IP67)

• Companding on/o

• Oponal customized call box labels (front / two sides)(Special order)

• Baery Operated (3 D-cell)

• Easy baery replacement

• Very low current consumpon when in ‘Sleep Mode’

• Low baery monitoring / low baery alert to radio channel users

• Obvious Acvaon buon

• Less obvious reset buon

• Local audio greeng message upon acvaon

• LED indicator when call box is acve (awake)

• Busy channel monitor before transmit

• Available transmit message alert tone, 9 to choose from

• Programmable ‘alert message repeat’ transmission me interval

• Locally recorded or pre-recorded .wav le audio messages

• Selectable ‘Sleep Mode’ delay mer. Automacally enters ‘Sleep Mode’ with inacvity.

• Adjustable local speaker volume

• Local audio to acknowledge call box clear

• Radio transmied clear message available

• Two call box back covers are available

1. Flat surface for wall mount or custom bracket applicaons (Standard)

2. Built in counter-top stand or square pole strap mounng (Special order)

Specicaons:

• UHF, 450MHz – 470MHz

• Power output, .5/2W

• Baery power – three D cell

• Water Resistant (IP67)

• Size: H 8.1875” x W 5.1” x D 2.75”

• Weight: 2.25lbs.

• Operang Temperature range: -25C to +55

AWR-CB2100 One-way Call box Operaon:

The AWR-CB2100 call box is congured for operaon by your radio dealer. Proper frequency informaon

and operang characteriscs are congured using programming soware. Your dealer will need to gather

operaonal informaon from you before the call box can be deployed. Once congured, the AWR-CB2100

will operate in the following manner:

• The AWR-CB2100 will be in ‘Sleep Mode’ (o) the majority of the me. During ‘Sleep Mode’, very

lile current is being consumed allowing for extended baery life.

• A press of the ‘Acvate’ buon will cause the call box to ‘wake-up’ and perform it’s programmed

dues.

1. A short beep will be heard when the acvate buon is inially pressed.

2. The ‘Speaker Message on Acvaon’ greeng message will be heard on the local call box speaker.

3. If the radio channel is not busy, the call box alert tone (if programmed) followed by the ‘Message

on Acvaon’ will be transmied to the associated two-way radios. The status LED will be red

when the call box is transming.

4. When ‘Awake’, the status LED will ash green when the call box is not transming or receiving to

indicate that the call box is acve.

5. If the call box reset buon is ‘NOT’ pressed, and if the call box is programmed for repeat messages

at a designated me period, the call box will transmit its rst repeat message to the associated

two-way radios. This process will connue for the programmed message delay me period and

the number of alert message repeats. If the call box is allowed to progress though all of the

programmed repeats, without being reset, the call box will automacally me-out and re-enter

Sleep Mode.

6. If the Reset buon is pressed, while the call box is acve, the alert message process is terminated.

7. The call box ‘Speaker Message on Clear’ (if programmed) will be played to the local speaker.

8. The call box ‘Message on Clear’ (if programmed) will be transmied to the associated two-way

radios.

9. When the call box ‘Message on Clear’ message transmission is complete, the AWR-CB2100 One-

way call box will re-enter ‘Sleep Mode”.

• Low Baery alert

Each me the AWR-CB2100 call box is acvated, the baery level is measured. If the baery level has

dropped to a low baery level condion, the call box will process the ‘Low Baery Alert’ message at

the end of each radio alert transmission. The radio users will hear the low baery alert message. The

call box local speaker will not hear the low baery alert message.

• Status LED

1. Call box is acve (awake) LED is ashing green

3. Call box is transming LED is steady red

4. Call box is in Sleep Mode LED is o

Advanced Operaonal Funconality:

• Recording audio messages using the on-board call box microphone. The call box MUST be in ‘Sleep

Mode’ when the following steps are started:

1. Press the ‘Acvate’ and ‘Reset’ buons simultaneously unl the status LED ashes two mes.

2. Press the ‘Acvate’ buon one me. A beep will be heard from the local speaker.

3. Addional presses of the acvate buon will step through the available message numbers, 1

through 16. (See default message list in “Notes” below)

4. Press the ‘Acvate’ buon unl the desired message number has been selected.

5. Press the reset buon to start recording.

• Speak clearly into the call box microphone.

• When the message is complete, press the reset buon again to stop recording.

NOTE: Pressing the reset buon a second me at this point will enter local speaker ‘Volume Set’

mode. See “Adjusng the Volume Level …” below for volume set details.

6. Press the ‘Acvate’ buon to remain in record mode. A beep will be heard.

7. Press the Acvate buon to select the next audio message number to record.

8. Repeat step 5 through 7 above for all desired audio messages.

9. To exit audio recording mode, press and hold the reset buon unl the status LED ashes red one

me.

10. The call box enters “sleep mode”.

Notes: When recording messages, speak clearly at approximately 6 to 12 inches from the call box

microphone.

A slight pause aer pressing the reset buon to start the recording is recommended.

Default message numbers:

Message 1 – Speaker message on acvaon

Message 2 – Transmit message on acvaon

Message 3 – Speaker message on clear

Message 4 – Transmit message on clear

Message 5 – Low baery alert

• Adjusng the volume level of the call box local speaker. The call box MUST be in ‘Sleep Mode’ when

the following steps are started:

1. Press the ‘Acvate’ and ‘Reset’ buons simultaneously unl the status LED ashes two mes.

2. Press the reset buon one me. A beep will be heard from the local speaker.

3. Addional reset buon presses will increment the volume level up, acvate buon presses will

increment the volume level down.

Note: There are 16 volume levels. 1 is the lowest, 16 is the highest.

4. To exit volume adjust mode, press and hold the Reset buon unl the status LED ashes red one

me.

5. The call box enters “Sleep Mode”.

• Test the One-way call box. Press the Acvate buon to conrm desired audio messages and local

speaker volume. Press the Reset buon to conrm desired audio messages.

THIS PAGE WAS LEFT INTENTIONALLY BLANK

All other trademarks are property of their respective owners.

20809 Kensington Blvd. Lakeville, MN 55044-8353

(800) 475-5852 www.advancedwireless.com

501044

Tabla de contenidos

Manuales populares de Sistema de intercomunicación de otras marcas

Bticino

Bticino LINEA 3000 Manual de usuario

MSI

MSI MSI-140 Manual de usuario

golmar

golmar Stadio Plus Manual de usuario

CyberData

CyberData 011211 series Manual

Vidos

Vidos duo M1021 Manual de usuario

Vimar

Vimar ELVOX 7539/E Manual de usuario

SSS Siedle

SSS Siedle BTSV 850-03 Manual de usuario

Dahua

Dahua VTO Series Manual de usuario

Elvox

Elvox 5651 Manual de usuario

Videx

Videx VIDEOKIT Series Manual de usuario

Rocom

Rocom Doortello Business FW T2.05W2.04 Manual de usuario

Viking

Viking E-35-EWP Manual de usuario

Safeguard Supply

Safeguard Supply LRA-EX1000 Manual de usuario

SSS Siedle

SSS Siedle BFCV 850 Series Manual de usuario

GRD

GRD MAX V2 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Aiphone

Aiphone IE-8MD Manual de usuario

Perel

Perel EDB4 Manual de usuario