Advance mobility Spirit Push Chair Manual de usuario
Read these
instructions carefully
before use and
keep them for
future reference.
Your passenger’s safety may
be affected if you do not
follow these instructions.
Assembly
Instructions
Spirit Push Chair
This product is CE approved.
A Division of The Baby Jogger Company
2
• WARNING: Prevent serious injury to your passenger by always using the
safety harness.
• WARNING: Any load attached to the handle affects the stability
of the push chair.
• WARNING: It may be dangerous to leave your passenger unattended.
• WARNING: Recommended weight for seat pocket is 2 pounds and basket
is 10 pounds. Excessive weight may cause a hazardous unstable
condition to exist.
• Accessories which are not approved by the manufacturer or distributor
should not be used.
• Always use your wrist strap – this push chair can really roll, and the
wrist strap gives you control if you should slip or fall down.
• The passenger should remain seated (no standing in push chair).
• Watch out for cars – never assume that a driver can see you.
• Intended for children aged 6 months and up.
• Total weight load recommended for this push chair is 75 lbs. (34 kg.)
(combined passenger and baggage weight.)
• This push chair seats one passenger.
• It may be unsafe to use replacement parts other than those supplied or
approved by the manufacturer.
• Do not run/jog with a baby under 6 months of age.
For the sake of your precious cargo, please read
these warnings before using your brand new
Spirit Push Chair.
EC-REP: European Device Solutions • Contact: [email protected]
1
Frame
1 Unpack the push chair from the box and set
wheels and footplate aside. 2 Unfold the push chair by lifting the
front fork away from the handlebar
until it clicks into place.
3 Turn stroller
over to upright
position.
EC-REP: European Device Solutions • Contact: [email protected]
2
Footplate
1 Insert the
footplate tab
into the footplate
holder slot.
2 Press down on
footplate until it
slides into place.
1 Using the two Velcro straps,
secure the front end of the under
seat basket to the frame just
above the footplate holder slot.
2 Snap the rear basket straps
around the frame.
Under Seat Basket
3
1 To install, squeeze the two brake
calipers together and push the
black lever backwards to open
brake pads. Release calipers so
that they spring open.
2 Insert the front wheel into the fork
tips by aligning the axle flats with
the fork tip flats.
Front Wheel
3 Tighten by turning the
wheel lever clockwise while
holding the opposite side.
4 Close the wheel lever by
pushing it flush against
the tubing. Be sure not
to over tighten – light
pressure is needed to
close the wheel lever. You
should not strain to close.
5 Squeeze the two brake
calipers together against
the metal rim of the front
wheel and flip the black
lever forwards to close
brake pads.
WARNING: Engage parking
brake before loading and
unloading passenger.
Rear Brake
1 Press down on
the brake pedal to
engage rear wheel
parking brake.
2 To release, flip the
lever upwards.
4
Rear Wheels
1 To install, slide the axle peg of the rear wheel
into the axle until you hear it click into place.
Complete on both sides.
2 To remove, push the round button on the
rear axle while pulling out the wheel.
5
Seat
2 At knee area of the seat, secure the seat to
the frame by threading one side of the Velcro
straps through the D-ring on the other.
1. Start with snapping seat
to upper frame and work
your way down frame.
3 Tighten and secure the Velcro together. 4 At foot area of the seat, secure the seat
to the frame by threading one side of
the Velcro straps through the D-ring on
the other.
6
6 Snap the seat strap around the support bar on the frame.
NOTE: The seat of your jogger can be
removed for washing. Unsnap the fabric
from the frame and undo any Velcro straps.
See page 15 for washing instructions.
5 Tighten and secure around the frame.
7
1 Un-clip top of shoulder strap from the seat
and re-clip on the pair of seat loops closest
to the child’s shoulder height.
3 Buckle harness by sliding harness pegs into
the buckle on the crotch strap until it locks
into place.
2 Adjust the strap length by moving the plastic
guide up or down to lengthen or shorten.
4 To unbuckle, squeeze the sides of the buckle
while pulling the two harness pegs out of
the buckle.
Safety Harness
8
Reclining Seat
2 Pull on strap when you want to return the
seat to its upright position.
1 Simply adjust seat straps to desired degree of
recline by releasing the length of the strap.
Tabla de contenidos
Otros manuales de Paseante de Advance mobility
