DISCONNECT THE POWERCORD BEFORE REPLACING LIGHTBULBS. Always , J//_.,.--- (Non-Dispenser Models Oz
use a40 watt, standard base,appliance type bulb when replacing a light.
DISPENSER LIGHT - DISPENSER MODELS ONLY. For replacement, use a 120V, This refrigerator may have been bui
7 watt bulb. Disconnect the power cord before replacing the light bulb. to the left. Referto the instructio
Tools Required
DISCONNECT POWER CORD BEFORE CLEANING. Your refrigerator can be Phillips screwdriver He:
moved out for cleaning.If yourmodel has anautomatic ice maker, werecom- End wrench . 5/16" Put
mend that youturn the water supply off before moving the cabinet. T27 Torx Driver
After cleaning behind yourmodel, push it back and turnthe levelers clockwise
to lock cabinet in place.
Inside REMOVE To Change theDoors
Clean both compartments and inner door panels with mild soap and water.DO TAPPINGPLATE1.Turn the fresh food control to
NOT use an abrasive powder, solvent,pohsh cleaner or undiluted detergent. REMOVE_._", food fromthe interior.
Use bakingsoda and warm water only on interior compartmentsand interior SCREW 2.Removethe handles fromthe q
door linen. Rinse with clearwater. Donot wash interior partsin yourdishwasher.
Be sure to wring out excess water fromthe sponge or cloth when cleaning in that youare goingto installthe
thearea of controls,lightsorelectrical parts, plugs with a putty knife and p
of the doors.
Youmay notice a slight discoloration appearing at thetop and near thecenter3.Using a socket screwdriver or
of the back wall of the fresh food compartment.This isno causefor alarm, butper hinge. Carefully lift thedog
it should be cleaned off periodically, and place it on a padded surl
Glass shelves can be removed and completely immersed in warm water. AL- spacer that was between the
LOW GLASS TO WARM TO ROOM TEMPERATURE BEFORE IMMERSING. HINGE SiDE4. Using a putty knife, pry the p]
REMOVE TAPPING PLATE the top of the door.Save the
Outside5. Lift the upper hinge and the s!
Keep the finish clean. Wipe with a clean, soft cloth lightly dampened with kitch-
en appliance wax or mild liquid dishwashing detergent. Dry and polish with INSTALL at the opposite corner.
-TAPPING PLATE6. Position the plug button cover
a clean,soft cloth. Do not wipe the refrigerator with a soiled dishwashing cloth
or wet towel. These may leave residue that can erode the paint. Do not use scour-_"_NSTALL ing and press it into place.
ing pads, powdered cleansers,bleach or cleaners containing bleach because 7. Pry out the three plastic plug 1
these products can scratch and weaken the paint finish, into the opposite corner.
Protect the paint finish. The finish on the outside of the refrigerator is a high-8. Unscrewthe hinge pin out of t
quality,baked-on paint finish. With proper care, it will stay new-looking and Carefullylift the lower door o:
rust-free for years. _surface• If the metalhinge pin
You door gaskets are vinyl. They may be cleaned with a baking soda solution, is removed, pull it out of the d
soap and water or with a mild scouring powder• 9. Remove the center hinge and
OPPOSITE SIDE screws from the left end of the
Removing Base Grills INSTALL TAPPING PLATEhinge and spacer on the left (
Grasp the base grille at both ends and pull straight out. To replace the base grille, installed on the right end.Ti!
then turn them one-half turn
align ths spring clips with the square openingsin the cabinet and push each end |SUPPORTRAILS 10. Pry the plugcover from the p
inuntil thegrinslocks into place.
tI/DEFROSTPAN _ and press into the plastic bu_
Defrost Pen _ 1 _--- 11. Remove the base grille by gras
Defrost water drains into a shallow pan beneath the cabinet and evaporates. 12. Remove the hinge cover by s¢
During periods of high humidity, water could remain in the pan. This pan should L models, remove the cover scre
be cleaned once a month with a strong solution of soap and water. 13. Use a5/16 socket and ratchet
To remove the defrost pan, remove the base grille and slide the pan out from , ,, . hinge. Save the spacer•
underneath the cabinet. To replace the defrost pan, position the side flanges I,i__-_ I 14.Using aT27 socket wrench,re]
to fit over slide rails end push it in until it stops. Replace the base grille, side of the refrigerator. Insl_
spacerto the left legof the cat
Condenser
The area around the condenser should be cleaned once a year for efficient oper- 15. Pull the metal hinge pin from
ation. It can be adequately cleaned through the right front of the base open-_• 0_,, including the spacerwasher, h
ings.Unplug the refrigerator and remove the base grille.Reach through the base_ _-,16.Pry out the two screwhole plt
opening with your vacuum cleaner attachment to clean the front and open end _
,,_ _ door and lowerdoor• Onsome
of the condenser,on the bottom of each dooran(
6plug buttons in the holes on
