ADJ UB 6H Manual de usuario

User Manual

UB 6HUB 6H

Rev 03/2021

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be trade-

marks or registered trademarks of their respective companies and are hereby acknowledged. All

non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 2

DOCUMENT VERSION

Please check www.adj.com for the latest revision/update of this document.

Date Document

Version

Software

Version >

DMX Channel

Mode

Notes

08/04/17 1 1.01 6/10/12/18 Initial Release

03/12/21 2 1.03 N/C Update for Primary/Secondary Mode

UB 6H Introduction

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 3

Unpacking: Thank you for purchasing the UB 6H by ADJ Products, LLC. Every UB 6H has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

have arrived intact. In the event that damage has been found or parts are missing, please contact our

toll free customer support number for further instructions. Do not return this unit to your dealer without

rst contacting customer support.

Introduction: The ADJ UB 6H is a DMX intelligent, LED bar xture. This xture can be used in a stand

alone set up or connected in a Primary/Secondary set up. This xture has six operating modes: Sound

Active mode, Auto Run mode, Static Color mode, RGBWA+UV Dimmer mode, Built-In Program mode,

and DMX control mode.

Customer Support: ADJ Products, LLC provides a customer support line, to provide set up help and

to answer any questions that may arise during initial set up or operation. You may also visit us on the

web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday

8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as

doing so will void your manufacturer’s warranty. In the unlikely event that your unit requires service,

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 4

UB 6H Features

• Multi-Colors

• Six Operating Modes

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• 3-Pin DMX Connection

• 4 DMX Modes: 6 Channel Mode, 10 Channel Mode, 12 Channel Mode, & 18 Channel Mode.

• Magnetic Quick Align (See the Magnetic Quick Align section of this manual)

• ADJ UC IR compatible and Airstream IR compatible

• Multiple Unit Power Linking Capability (See the Multiple Unit Power Linking section of this man-

ual for details)

UB 6H Warranty Registration

The UB 6H carries a 2 year limited warranty. Please fill out the enclosed warranty card to validate your

purchase. All returned service items, whether under warranty or not, must be freight pre-paid and

accompanied by a return authorization (R.A.) number. The R.A. number must be clearly written on the

outside of the return package. A brief description of the problem as well as the R.A. number must also

be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you

must provide a copy of your proof of purchase invoice. You may obtain an R.A. number by contact-

ing our customer support team on our customer support number. All packages returned to the service

department not displaying an R.A. number on the outside of the package will be returned to the ship-

per.

UB 6H Installation

The unit should be mounted using a mounting clamp (not provided), which should be attached to the

mounting bracket that is provided with the unit. Always ensure that the unit is firmly fixed to avoid

vibration and slipping while operating. Always ensure that the structure to which you are attaching

the unit is secure and is able to support at least 10 times the unit’s weight. Also, always use a safety

cable that can hold at least 12 times the weight of the unit.

The equipment must be installed by a professional, and it must be installed in a place where it is out

of the reach of people’s grasp.

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 5

UB 6H Safety Precautions

• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord is frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover for any reason. There are no user serviceable parts inside.

• Never operate this unit with the cover removed.

• Never plug this unit in to a dimmer pack.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit if it has been damanged in any way.

• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit from the power outlet.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point at which they exit from

the unit.

• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the

Cleaning section of this manual for cleaning details.

• Heat - The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen onto, or liquid has been spilled into, the fixture.

C. The fixture has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a marked change in performance.

UB 6H Safety Precautions

RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!

FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT AT A WAVELENGTH OF 390NM -

410NM.

WEAR PROPER EYE AND SKIN PROTECTION.

AVOID PROLONGED PERIODS OF EXPOSURE.

AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.

AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES OF LESS THAN 11 feet (3.3m).

DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER PROTECTIVE

LENS.

DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH

OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.

INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE

DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION MAY EXPERIENCE

DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 6

UB 6H DMX Set Up

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 7

Power Supply: The ADJ UB 6H contains an automatic voltage switch, which will automatically sense

the voltage when it is plugged into the power source. With this switch, there is no need to worry about

the correct power voltage, and this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol that is used as a form

of communication between intelligent fixtures and controllers. A DMX controller sends DMX data

instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture

to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most control-

lers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be

linked together and operate from a single controller, as long as all fixtures and the controller are DMX

compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible

when linking several DMX fixtures. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The UB 6H can be controlled via

DMX-512 protocol. The UB 6H has 4 DMX channel modes; please see the Channel Mode sections of

this manual for the different modes. Your unit and your DMX controller require a standard 3-pin XLR

connector for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you

are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may

be purchased at almost all pro lighting stores). Your cables should be made with a male XLR connec-

tor at one end of the cable and a female XLR connector at the other. Also remember that DMX cable

must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 8

Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come into contact with the XLR cable’s outer casing. Grounding the shield could

cause a short circuit and result in erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter-

minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor

which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is

inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a

cable terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-

mission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When insert-

ing standard 5-pin data cables into a 3-pin line, a cable adaptor must be used. These adaptors are

readily available at most electronics stores. The chart below details a proper cable conversion.

UB 6H DMX Set Up

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 9

UB 6H Operating Instructions

LED Display On/Off:

To set the LED display to turn off after 10 seconds of inactivity, press the MODE button until “don” is

displayed, then press the UP button until “doff” is displayed on the screen. Now the display will turn

off after 10s. Press any button to turn the display on again.

LED Display Inversion:

Follow these instructions to flip the display 180° so that the display can be read when the unit is

mounted upside down.

1. Plug the fixture in and press the MODE button until “dXX” is displayed. “XX” represents either

“on” or “oFF”.

2. Press the SET UP button until “Stnd” is displayed.

3. Press the UP or DOWN buttons to “flip” the display 180°.

Operating Modes:

The UB 6H has six operating modes:

• Static Color Mode - There are 63 colors to choose from.

• RGBWA+UV Dimmer Mode - Choose one of the 6 colors to remain static, or adjust the intensity

of each color to create a custom color.

• Built-In Program - There are 22 built-in programs to choose from with multiple adjustments.

• Auto Run - An auto program will run with adjustable fade speed and strobe.

• Sound-Active mode - The unit will react to sound, chasing through the built in programs.

• DMX control mode - This function will allow you to control each DMX trait with a standard DMX

512 controller.

Static Color Mode:

1. Plug the fixture in and press the MODE button until “CLXX” is displayed.

2. There are 63 colors to choose from. Select your desired color by pressing the UP and DOWN

buttons. After you have selected your desired color you can activate strobing by pressing the

SET UP button to enter the Flash (strobe) mode.

3. “FS.XX” will now be displayed, indicating that the device is now in Flash mode. The Flash can be

adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

ADJ Products, LLC - www.adj.com - UB 6H User Manual Page 10

UB 6H Operating Instructions

RGBWA & UV Dimmer Mode:

1. Plug the fixture in and press the MODE button until “r.XXX” is displayed. You are in Red dimming

mode.

2. Press the UP and DOWN buttons to adjust intensity. After you have finished adjusting the inten-

sity, or if you would like to skip to the next color, press the SET UP button.

3. When “G.XXX” is displayed you are in Green dimming mode. Press the UP and DOWN buttons to

adjust intensity.

4. When “b.XXX” is displayed you are in Blue dimming mode. Press the UP and DOWN buttons to

adjust intensity.

5. When “U.XXX” is displayed you are in White dimming mode. Press the UP and DOWN buttons to

adjust intensity.

6. When “A.XXX” is displayed you are in Amber dimming mode. Press the UP and DOWN buttons to

adjust intensity.

7. When “u.XXX” is displayed you are in UV dimming mode. Press the UP and DOWN buttons to

adjust intensity.

8. After you have adjusted the colors to make your desired color you can then activate strobing by

pressing the SET UP button to enter the strobe mode.

9. “FSXX” will be displayed, indicating that the device is now in strobe mode. The strobe can be

adjusted between “00” (flash off) to “15” (fastest flash).

Auto Run Mode:

In this mode the fixture will run an auto program.

1. Plug the fixture in and press the MODE button until “AUTO” is displayed.

2. After you have activated Auto Run mode, press the SET UP button to adjust the fade time.

3. Once you press SET UP “Fd.XX” should be displayed. Use the UP or DOWN buttons to set the

fade speed to either “Fd.00” (fade off) or between “Fd.01” (fastest speed) and “Fd.99” (slowest

speed). After adjusting the fade speed, press SET UP if you wish to activate the Flash mode.

4. “FS.XX” will now be displayed, indicating that the device is now in Flash mode. The Flash can be

adjusted between “FS.00” (flash off) to “FS.15” (fastest flash).

Tabla de contenidos

Otros manuales de Equipo de iluminación de ADJ

ADJ

ADJ VIZI WASH Z19 Manual de usuario

ADJ

ADJ INNO POCKET Z4 Manual de usuario

ADJ

ADJ Flat Par Tri18 Manual de usuario

ADJ

ADJ Double Phase LED Manual de usuario

ADJ

ADJ Micro Royal Galaxian Manual de usuario

ADJ

ADJ SPS-2B Manual de usuario

ADJ

ADJ Royal Sky Manual de usuario

ADJ

ADJ Jelly Par Profile System Manual de usuario

ADJ

ADJ Revo Burst Manual de usuario

ADJ

ADJ LED UV GO Manual de usuario

ADJ

ADJ 1227000010 Manual de usuario

ADJ

ADJ WiFly Bar RGBA Manual de usuario

ADJ

ADJ VIZI WASH Z37 Manual de usuario

ADJ

ADJ FOCUS FLEX L19 Manual de usuario

ADJ

ADJ COLOR STRAND LED Manual de usuario

ADJ

ADJ COB CANNON WASH Manual de usuario

ADJ

ADJ SWEEPER BEAM QUAD LED Manual de usuario

ADJ

ADJ ELE600 Manual de usuario

ADJ

ADJ COB CANNON WASH ST DW Manual de usuario

ADJ

ADJ MEGA GO FLOOD BAR Manual de usuario

ADJ

ADJ 12PX HEX PEARL Manual de usuario

ADJ

ADJ ULTRA HEX BAR 12 Manual de usuario

ADJ

ADJ ACCU-STAND LTS2 AS Manual de usuario

ADJ

ADJ 12P HEX IP Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario