ADJ SWEEPER BEAM QUAD LED Manual de usuario
User Manual
SWEEPER BEAM
QUAD LED
Rev. 01/2021
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 2
Unpacking: Thank you for purchasing the Sweeper Beam Quad LED by ADJ Products, LLC. Every
Sweeper Beam Quad LED has been thoroughly tested and has been shipped in perfect operating
condition. Carefully check the shipping carton for damage that may have occurred during shipping. If
the carton appears to be damaged, carefully inspect your xture for any damage and be sure all equip-
ment necessary to operate the unit has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not
return this unit to your dealer without contacting customer support rst.
Introduction: The Sweeper Beam Quad LED is an intelligent, multi-LED scanner. The Sweeper Beam
Quad LED can operate as a stand alone xture or in a Primary/Secondary conguration. The Sweeper
Beam Quad LED has three operating modes: sound active mode, show mode, and DMX control. This
xture is suitable for theaters, studios, retail stores, and other similar locations. For best results use
fog or special eects smoke to enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide help and
to answer any questions that may arise during your set up or initial operation. You may also visit us on
the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday
8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
Warning! This unit can cause severe eye damage! Never look directly into the light source!
Sweeper Beam Quad LED General Information
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 3
Sweeper Beam Quad LED General Instructions
To optimize the performance of this product, please read these operating instructions carefully to
familiarize yourself with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit, for
future reference.
• DMX-512 Protocol
• 4 DMX Channel Modes (1 Channel Mode, 6 Channel Mode, 35 Channel Mode, & 39 Channel
Mode)
• 3 Operating Modes - Sound Active, Show Mode, and DMX Control
• Internal Microphone
• Digital Display for Address and Function Setting
• UC3 Controller
The Sweeper Beam Quad LED carries a 3 year (1095 day) limited warranty. Please fill out the
enclosed warranty card to validate your purchase and warranty. You may also register your product
online at www.adj.com. All returned service items, whether under warranty or not, must be freight pre-
paid and accompanied by a return authorization (R.A.) number. If the unit is under warranty, you must
provide a copy of your proof of purchase invoice. Please contact ADJ Products, LLC customer sup-
port for an R.A. number.
Sweeper Beam Quad LED Warranty Registration
Sweeper Beam Quad LED Features
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-obser-
vance of this manual or any unauthorized modifications to this unit.
Sweeper Beam Quad LED Handling Precautions
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 4
Sweeper Beam Quad LED Safety Precautions
For Your Own Personal Safety, Please Read and Understand This Manual Completely Before
You Attempt To Install Or Operate This Unit!
• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required voltage for your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken.
• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is
used to reduce the risk of electrical shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit with its cover removed.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
• Do not attempt to operate this unit if it has been damaged in any way.
• This unit is intended for indoor use only, use of this product outdoors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. Pay particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the device.
• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the
Cleaning section of this manual for detailed information.
• Heat - This fixture should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into, the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a marked change in perfor-
mance.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 5
Sweeper Beam Quad LED Handling Precautions
Fixture installation must always be secured with a secondary safety attachment, such as an appropri-
ately rated safety cable.
Regardless of the rigging option you choose for your Sweeper Beam Quad LED, always be sure to
secure your fixture with a safety cable (not included).
Caution: For added protection mount the fixtures in areas outside of walking paths, seating areas, or
areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a minimum
point load of 10 times the device’s weight.
To avoid injury, never stand directly below the device when mounting, removing, or servicing the fix-
ture.
Always use and install a safety cable (not included) as a safety measure to prevent accidental damage
and/or injury in the event the clamp fails.
Be sure to complete all rigging and installation procedures before connecting the main power cord to
the appropriate wall outlet.
Sweeper Beam Quad LED Set Up
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 6
Power Supply: The ADJ Sweeper Beam Quad LED contains an automatic voltage switch, which will
auto sense the voltage when it is plugged into the power source. With this switch there is no need to
worry about the correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and
controller manufacturers as a form of communication between intelligent xtures and controllers. A
DMX controller sends DMX data instructions from the controller to the xture. DMX data is sent as
serial data that travels from xture to xture via the DATA “IN” and DATA “OUT” XLR terminals locat-
ed on all DMX xtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufacturers to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX xtures try to use
the shortest cable path possible. The order in which xtures are connected in a DMX line does not
inuence the DMX addressing. For example, a xture assigned a DMX address of 1 may be placed
anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a xture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Primary/Secondary Operation): The
Sweeper Beam Quad LED can be controlled via DMX-512 protocol. The Sweeper Beam Quad LED
has 4 DMX Channel Modes. The DMX address is set electronically using the controls on the rear
panel of the unit. Your unit and your DMX controller require an approved DMX-512 110 Ohm Data
cable for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard 110-120 Ohm shielded cable (this cable may be
purchased at almost all professional sound and lighting stores). Your cables should be made with a
male and female XLR connector on either end of the cable. Also remember that DMX cable must be
daisy chained and cannot be split.
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 7
Sweeper Beam Quad LED Set Up
Notice: Be sure to follow gures two and three when making your own cables. Do not use the
ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug
or allow the shield conductor to come in contact with the XLR cable’s outer casing. Grounding the
shield could cause a short circuit and erratic behavior.
Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-
nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which
is connected between pins 2 and 3 of a male XLR connector (DATA+ and DATA-). This unit is inserted
in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.
5-Pin XLR DMX Connectors. This unit use 5-pin DMX-512 data cables for DATA transmission. 5-pin
DMX xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in
to a 3-pin line, a cable adaptor must be used. These adaptors are readily available at most electron-
ics stores. The chart below details a proper cable conversion.
Sweeper Beam Quad LED System Menu
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 8
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 9
System Menu: When making adjustments press ENTER to conrm your setup and then press
and hold the MENU button for at least 3 seconds. To exit without making any adjustments
press the MENU button.
ADDR - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, and press ENTER.
2. The current address will now be displayed and ashing. Press the UP or DOWN buttons to nd
your desired address. Press ENTER and then press and hold the MENU button to set your de-
sired DMX address.
CHND - This will let select your desired DMX channel mode.
1. Press the either the MENU button until “CHND” is displayed, and press ENTER. Either “1CH”,
“6CH”, “35CH”, or “39CH” will be displayed.
2. Press the UP or DOWN buttons to choose your desired DMX mode and press ENTER to conm
and exit.
SCND - This will let you set unit as a primary or a secondary in a primary/secondary congu-
ration.
1. Press the MENU button until “SCND” is displayed, and press ENTER. Either “PRI,” “SEC1,” or
“SEC2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER and then
press and hold the MENU button to conm.
NOTE: In a Primary/Secondary conguration, setting the Secondary units to “SEC2” will cause the
primary and secondary units to have contrasting movements.
SET - This will set the Sweeper to a preset angle.
1. Press the either the MENU button until “SET” is displayed, and press ENTER. Either “150”, “120”,
or “90” will be displayed. These are the preset angles.
2. Press the UP or DOWN buttons to choose your desired angle and press ENTER to conm and
exit.
SHND: SH 0 - SH16 - Show modes 0-16 (Factory programs). Show mode can run with or with-
out sound active mode.
1. Press the MENU button until “SHND” is displayed, and press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between 0-16. Programs 1-16 are fac-
tory programs, while “Sh 0” is random mode. Press the UP or DOWN buttons to nd your desired
show.
3. When you have found your desired show press ENTER, then press and hold the MENU button for
at least 3 seconds to activate.
SOUN - Sound Active mode.
1. Press the MENU button until “SOUN” is displayed, and press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to
activate sound active mode, or “OFF” to deactivate sound active mode.
3. Press ENTER, and then press and hold the MENU button for at least 3 seconds to activate.
Sweeper Beam Quad LED System Menu
ADJ Products, LLC - www.adj.com - Sweeper Beam Quad LED User Manual Page 10
SENS - Sound sensitivity control.
1. Press the MENU button until “SENS” is displayed, and press ENTER.
2. The display will show a number between 0-100. Press the UP or DOWN buttons to adjust the
sound sensitivity. 0 is the least sensitive and 100 is the most sensitive.
3. Press the ENTER button to conrm.
DNST - This mode denes the behavior of the xture in the event that the DMX signal is lost
or interrupted. You can also set this as the operating mode you would like the unit to return to
when power is applied.
1. Press the MENU button until “DNST” is displayed, press ENTER.
2. Either “PRSE”, “BLND”, or “LAST” will be displayed. Choose an operating mode you would like
the unit to start up in when power is applied or the DMX signal is lost.
A. PRSE (Primary/Secondary) - If the DMX signal is lost or power is applied, the unit will auto-
matically go into Primary/Secondary mode.
B. BLND (Blackout) - If the DMX signal is lost or power is applied, the unit will automatically go
into stand by mode.
C. LAST (Last State) - If the DMX signal is lost the xture will stay in the last DMX set up. If
power is applied and this mode is set, the unit will automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
LED - With this function you can have the LED display turn o after 10 seconds.
1. Press the MENU button until “LED” is displayed, and press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to
keep the LED display on at all times, or “OFF” to switch to have the LED display switch o after
10 seconds. To make the display reappear, press and hold the MENU button for at least 5 secs.
3. Press ENTER to conrm. To make the display reappear, press and hold the MENU button for at
least 5 secs.
DISP - This will “ip” the LED display 180º.
1. Press the MENU button until “DISP” is displayed, and press ENTER.
2. Either “DISP” or “DSIP” will now be displayed. Press the ENTER button to “ip” the display.
TILT - This function activates tilt inversion.
1. Press the MENU button until “TILT” is displayed, and press ENTER.
2. The display will show either “YES” or “NO”. Press the UP or DOWN buttons to select “YES” to
activate tilt inversion, or “NO” to deactivate tilt inversion.
3. Press ENTER, and then press and hold the MENU button for at least 3 seconds to activate.
Sweeper Beam Quad LED System Menu
Otros manuales para SWEEPER BEAM QUAD LED
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipo de iluminación de ADJ
ADJ
ADJ WiFly Par QA5 WH Manual de usuario
ADJ
ADJ ikon profile ww Manual de usuario
ADJ
ADJ WiFly Bar RGBA Manual de usuario
ADJ
ADJ WiFlY EXR HEX PAR Manual de usuario
ADJ
ADJ JOLT PANEL FX Manual de usuario
ADJ
ADJ INNO POCKET SPOT TWINS Manual de usuario
ADJ
ADJ ENCORE FR PRO COLOR Manual de usuario
ADJ
ADJ HYDRO SPOT 2 Manual de usuario
ADJ
ADJ Ricochet Manual de usuario
ADJ
ADJ ULTRA HEX BAR 12 Manual de usuario
ADJ
ADJ Revo sweep Manual de usuario
ADJ
ADJ Mega QA Par38 Manual de usuario
ADJ
ADJ Ikon Profile Manual de usuario
ADJ
ADJ VIZI HEX WASH7 Manual de usuario
ADJ
ADJ Rainbow PP Manual de usuario
ADJ
ADJ DMX OPERATOR-I Manual de usuario
ADJ
ADJ ANI-MOTION Manual de usuario
ADJ
ADJ VBar Pak Manual de usuario
ADJ
ADJ WIFLY PAR QA5 Manual de usuario
ADJ
ADJ Starburst Instrucciones de instalación
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
