ADJ Quad Phase HP Manual de usuario

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 1

User Instructions

QUAD PHASE HP

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 2

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product

names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes

all forms and matters of copyrightable materials and information now allowed by statutory or judicial

law or hereinafter granted. Product names used in this document may be trademarks or registered

trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC

brands and product names are trademarks or registered trademarks of their respective companies.

ADJ Products, LLC and all afliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as a

result of the improper, unsafe, insufcient and negligent assembly, installation, rigging, and operation

of this product.

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC warning

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the environment. Please turn off all electrical

products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

Quad Phase HP Introduction

Unpacking: Thank you for purchasing the Quad Phase HP by ADJ Products, LLC. Every

Quad Phase HP has been thoroughly tested and has been shipped in perfect operating

condition. Carefully check the shipping carton for damage that may have occurred during

shipping. If the carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has arrived intact.

In the event damage has been found or parts are missing, please contact our toll free

customer support number for further instructions. Please do not return this unit to your

dealer without contacting customer support rst.

Introduction: The Quad Phase HP is a four channel, DMX intelligent LED moonower

xture. The xture can operate in as a stand alone xture or in a Primary/Secondary

conguration. The Quad Phase HP has two operating modes; sound active and DMX

Control. For best results use fog or special effects smoke to enhance the beams

projections.

Customer Support: Contact ADJ Service for any product related service and support

needs. Also visit forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit http://parts.americandj.com

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-832-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET Voice: +31 45 546 85

60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | [email protected]

ADJ SUPPLY Europe B.V.

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit

to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself, doing so will void your manufactures warranty. In the unlikely event your unit

may require service please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 3

Quad Phase HP Features

• DMX-512 Protocol Compatible (Four DMX Channels)

• RGBW• Bright 32 Watt LED

• 2 Operating Modes - Sound Active & DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

• UC-IR Remote Included

• Power Cord Daisy Chain

Quad Phase HP Warranty Registration

The Quad Phase HP carries a 2 year (730 days) limited warranty. Please ll out the

enclosed warranty card to validate your purchase and warranty. You may also register

your product online at www.americandj.com. All returned service items whether under

warranty or not, must be freight pre-paid and accompany a return authorization (R.A.)

number. If the unit is under warranty you must provide a copy of your proof of purchase

invoice. Please contact ADJ customer support for a R.A. number.

Quad Phase HP Handling Precautions

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself, doing so will void your manufactures warranty. In the unlikely event your unit

may require service please contact ADJ Products, LLC.

During operation the housing may become extremely hot. Avoid touching the unit with

bare hands while in use.

ADJ Products, LLC will not accept any liability for any resulting damages caused by the

non-observance of this manual or any unauthorized modication to this unit.

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 4

Quad Phase HP Safety Precautions

For Your Own Personal Safety, Please Read and Understand This Manual

Completely Before You Attempt To Install Or Operate This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt- age for your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This

prong is used to reduce the risk of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts

inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow

about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to cords

at plugs, convenience receptacles, and the point where they exit from the appliance.

• Cleaning -The xture should be cleaned only as recommended by the manufacturer.

See page 16 for cleaning details.

• Heat -This xture should be situated away from heat sources such as radiators, heat

registers, stoves, or other appliances (including ampliers) that produce heat.

• The xture should be serviced by qualied service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits amarked change

in performance.

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 5

Quad Phase HP DMX Setup

Power Supply: The ADJ Quad Phase HP contains a automatic volt-age switch, which

will auto sense the voltage when it is plugged into the power source. With this switch

there is no need to worry about the correct power voltage, this unit can be plugged in

anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-tocol used by most

lighting and controller manufactures as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions from the controller

to the x- ture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers

only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufactures

to be linked together and operate from a sin- gle controller, as long as all xtures and

the controller are DMX com- pliant. To ensure proper DMX data transmission, when

using several DMX xtures try to use the shortest cable path possible. The order in

which xtures are connected in a DMX line does not inuence the DMX addressing. For

example; a xture assigned a DMX address of 1 may be placed anywhere in a DMX

line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned

a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to

that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Primary/SecondaryOperation):

The Quad Phase HP can bceontrolled via DMX-512 protocol. The Quad Phase HP is

a four channel DMX unit. The DMX address is

set electronically using the controls on the back

panel of the unit. Your unit and your DMXcontroller

require aapproved DMX-512 110 Ohm Data

cable for data input and data output (Figure

1). We recommend Accu-Cable DMX cables. If

you are making your own cables, besure to use

standard110-120 Ohm shielded cable (This cable

may bepurchased at almost all professional sound

and lighting stores). Your cables should be made

with a male and female XLR connector on either

end of the cable. Also remember that DMX cable

must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 6

Quad Phase HP DMX Setup

Notice: Be sure to follow gures two and three when making your own cables. Do not

use the ground lug on the XLR connector. Do not connect the cable’s shield conductor

to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need

to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120

ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector

(DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit

in your daisy chain to terminate the line. Using a cable terminator (ADJ part number

Z-DMX/T) will decrease the possibilities of erratic behavior.

1 Ground

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

DMX-512 OUT 3-PIN XLR

XLR Male Socket

2 Cold

DMX-512 IN 3-PIN XLR

COMMON

DMX +

DMX -

3 Hot

XLR Female Socket

1 Ground

3 Hot

2 Cold

Termination reduces signal errors and avoids signal

transmission problems and interference. It is always

advisable to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3

(DMX +) of the last xture.

5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-512 data cables for

DATA transmission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin

DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adapter

must be used, these adapters are readily available at most electric stores. The chart

below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 3-Pin XLR Female (Out) 5-Pin XLR Male (In)

Ground/Shield Pin 1 Pin 1

Data Compliment (- signal) Pin 2 Pin 2

Data True (+ signal) Pin 3 Pin 3

Not Used Do Not Use

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 7

Quad Phase HP Installation

The unit should be mounted using a mounting clamp (not provided), afxing it to the

mounting bracket that is provided with the unit. Always ensure that the unit is rmly

xed to avoid vibration and slipping while operating. Always ensure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times the

unit’s weight. Also, always use a safety cable that can hold 12 times the weight of the

unit when installing the xture. The equipment must be installed by a professional, and it

must be installed in a place where it is out of the reach of people’s grasp.

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 8

Quad Phase HP System Menu

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 9

Quad Phase HP System Menu

ADDR - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until "ADDR" is displayed, press

ENTER.

2. "1" will now be displayed and ashing. Press the UP or DOWN buttons to nd your

desired address. Press ENTER to set your desired OMX address.

SCnd - This will let you set unit as a Pri or Sec in a Primary/Secondry conguration.

1. Press the MENU button until "SCND" is displayed, then press ENTER. "PrI", "SEC1"

or "SEC2" will be displayed.

2. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to

conrm and exit.

SOUN - Sound Active mode.

1. Press the MENU button until "SOUN" is displayed, press ENTER.

2. The display will show either "ON" or "OFF". Press the UP or DOWN buttons to select

"ON" to activate sound active mode, or "OFF" to deactivate sound active mode.

3. Press ENTER to conrm.

SENS - Using this mode, you can set the sound sensitivity level. 0 for least sensitive, 100

for more sensitive.

1. Press the MENU button until "SENS" is displayed, press ENTER.

2. Using the UP or DOWN buttons adjust the sensivity level to your desire.

3. When you found your desired level, press the ENTER, and then press and hold the

MENU button for at least 3 seconds to conrm.

DNST - This mode can be used as a precaution mode, that in case the DMX signal

is lost, the operating mode chosen in the setup is the running mode the xture will

go into when the DMX signal is lost. You can also set this as the operat- ing mode

you would like the unit to return to when power is applied.

1. Press the MENU button until “DNST” is displayed press ENTER.

2. Either “Pr Se”, “BLND”, or “LAST” will be displayed. Choosean operating mode you

would like the unit to start up when power is applied or the DMX signal is lost.

• Pr Se (Primary/Secondry) - If the DMX signal is lost, or power is applied, the

unit will automatically go into Primary Secondry mode.

• BLND (Blackout) - If the DMX signal is lost or power is applied, the unit will

automatically go into stand by mode.

• LAST (Last State) - If the DMX signal is lost the xture will stay in the last DMX set

up. If power is applied and this mode is set, the unit will automatically go into the

last DMX set up.

3. Press ENTER to conrm your desired set up.

ADJ Products, LLC - www.adj.com - Quad Phase HP - User Manual - Page 10

Otros manuales para Quad Phase HP

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de ADJ

ADJ

ADJ Spherion WH LED Manual de usuario

ADJ

ADJ COLOR STRAND LED Manual de usuario

ADJ

ADJ Event Bar Q4 Manual de usuario

ADJ

ADJ WiFly Bar RGBA Manual de usuario

ADJ

ADJ FOCUS SPOT 7Z Manual de usuario

ADJ

ADJ SWEEPER BEAM QUAD LED Manual de usuario

ADJ

ADJ PINPOINT GO Manual de usuario

ADJ

ADJ HYDRO BEAM X12 Manual de usuario

ADJ

ADJ ENCORE BURST UV IP Manual de usuario

ADJ

ADJ RGB 3C Manual de usuario

ADJ

ADJ micro hypnotic Manual de usuario

ADJ

ADJ HEXCON Instrucciones de instalación

ADJ

ADJ MEGA GO FLOOD BAR Manual de usuario

ADJ

ADJ EVENT BAR PRO Manual de usuario

ADJ

ADJ Lightning COB Cannon Manual de usuario

ADJ

ADJ 3 SIXTY 2R Manual de usuario

ADJ

ADJ SDC24 Manual de usuario

ADJ

ADJ ACCU-STAND CSL100 Manual de usuario

ADJ

ADJ ENCORE LP7IP Manual de usuario

ADJ

ADJ Mega QA Go Manual de usuario

ADJ

ADJ InnoColor Beam12 Manual de usuario

ADJ

ADJ SP-1500 Manual de usuario

ADJ

ADJ ikon profile ww Manual de usuario

ADJ

ADJ UB 12H Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario