ADC FlexWave nano Manual
Confidential 8/11/2008
Mobile Network Solutions
FlexWave™ BSS
FlexWave™ nano Hardware Installation
AGCP
ADCP 75-313 •Issue 2
•
07/2008
D-620056-0-20,
R
ev A
© 2008 ADC Telecommunications, Inc. Page 1
8/11/2008
REVISION HISTORY
ISSUE DATE
1 06/2007 Original
2 07/2008 Update for Release 3.2
LIST OF CHANGES
The technical changes incorporated into this issue are listed below.
LIST OF CHANGES
All New publication
Generic Revisions for 3.2 software
COPYRIGHT
© 2008, ADC Telecommunications, Inc. All Rights Reserved. Neither this document, nor any
part may be copied, reproduced, modified, transmitted in any form or by any means,
electronically or mechanically, nor shall any derivative works be created without the
express prior written consent of ADC Telecommunications Inc.
TRADEMARK INFORMATION
ADC is a registered trademark and InterReach, InterReach Unison, InterReach Fusion,
WAVEXchange, FlexWave are registered trademarks and trademarks of ADC
Telecommunications, Inc. or LGC Wireless, Inc. a wholly owned subsidiary of ADC. All other
products, company names, service marks, and trademarks mentioned in this document or
website are used for identification purposes only and may be owned by other companies.
DISCLAIMER OF LIABILITY
Contents herein are current as of the date of publication. ADC reserves the right to change
the contents without prior notice. In no event shall ADC be liable for any damages
resulting from loss of data, loss of use, or loss of profits and ADC further disclaims
any and all liability for indirect, incidental, special, consequential or other similar
damages. This disclaimer of liability applies to all products, publications and
services during and after the warranty period.
This publication may be verified at any time by contacting ADC’s Technical Assistance
Center at 1-800-366-3891, extension 73476 (in U.S.A. or Canada) or 952-917-3476
© 2008 ADC Telecommunications, Inc.
Confidential 8/11/2008
DISPOSAL OF ELECTRONIC AND ELECTRICAL WASTE
Pursuant to the WEEE EU Directive electronic and electrical
waste must not be disposed of with unsorted waste. Please
contact your local recycling authority for disposal of this
product.
© 2008 ADC Telecommunications, Inc. Page 3
Confidential 8/11/2008
Table of Contents
1Introduction............................................................................................ 5
1.1 Purpose and Scope................................................................................5
2Warnings................................................................................................ 6
3Regulatory Information ............................................................................ 7
4Unpacking .............................................................................................. 8
5Fitting the External Antenna Kit (optional)................................................... 9
5.1 139/140 Hardware ................................................................................9
5.2 165 Hardware.................................................................................... 10
6Cabling the FlexWave™ nano ...................................................................12
6.1 139/140 Hardware .............................................................................. 12
6.2 165 Hardware.................................................................................... 12
6.3 Ethernet .......................................................................................... 13
6.4 Timing Interface Bus (TIB) – Multi-TRX only ................................................ 13
6.5 Chassis Bond Strap – Multi-TRX only.......................................................... 14
7Mounting the FlexWave™ nano.................................................................16
7.1 Mounting Multi-TRX FlexWave™ nano ........................................................ 18
7.2 Mounting Multi-TRX 165 FlexWave™ nano................................................... 18
8Initial Frequency Calibration.....................................................................19
9LED Status Indicators..............................................................................20
10 Annex A – Drawing 165#018 ...................................................................22
© 2008 ADC Telecommunications, Inc. Page 4
Confidential 8/11/2008
1Introduction
1.1 Purpose and Scope
This document describes the procedure used to install the FlexWave™ nano
hardware and physical connections together with applying the base software
configuration.
© 2008 ADC Telecommunications, Inc. Page 5
Confidential 8/11/2008
2Warnings
Please refer to the appropriate section of ADCP-75-311 [1].
© 2008 ADC Telecommunications, Inc. Page 6
Confidential 8/11/2008
3Regulatory Information
For all regulatory information please see ADCP-75-311 [1].
© 2008 ADC Telecommunications, Inc. Page 7
Confidential 8/11/2008
4Unpacking
Unpack FlexWave™ nano and check to see that the unit has not been damaged in
transit. Any damaged units should be returned to your supplier.
Figure 1 - Unpacking the FlexWave™ nano
© 2008 ADC Telecommunications, Inc. Page 8
Confidential 8/11/2008
5Fitting the External Antenna Kit
(optional)
5.1 139/140 Hardware
NOTE: When looking at the FlexWave™ nano with the connections facing down and
the LED visible the antenna on the left is the Transmit antenna and the antenna on
the right hand side is the Receive antenna.
NOTE: The RF feeder cable must not be bent sharply as this may result in a
degraded performance.
Remove the plastic covers by removing the top and bottom plates from both ends of
the FlexWave™ nano . Lever gently apart with screwdriver in notch.
Antenna Cover
Top
Antenna Cover
Bottom
Notch to aid
removal of
cover
Antenna Cover
Body
Figure 2 - Removal of antenna covers
Remove the antenna cover body, by unscrewing the two Torx T20 screws retaining
© 2008 ADC Telecommunications, Inc. Page 9
Confidential 8/11/2008
Remove Torx Screws
Figure 3 - Removal of antenna cover body
Fit the replacement antenna cover body ensuring that the feeder cable connector fits
into the antenna. Note that one cover only fits the receiver whilst the other fits the
transmitter.
Fit the clamp as shown below and second Torx screw, then replace top and bottom
covers.
Clamp plate
Compression
Spring
Figure 4 - Fit clamp plate
Repeat the process for the other end of FlexWave™ nano.
5.2 165 Hardware
NOTE: When looking at the front of 165 FlexWave™ nano with the Ethernet and TIB
connectors facing downwards, the TX antenna is bottom left, the RX antenna is
bottom right and the Network Listen (NWL) antenna is top right.
To fit external antennas, remove the plastic cover from the unit and unscrew the the
antennas to expose the SMA connectors. Connect directly to these connectors.
© 2008 ADC Telecommunications, Inc Page 10
Tabla de contenidos
Otros manuales de Accesorios de ADC
