Acer AT350 F3 Manual de usuario
AT350 F3
User Guide
System setup
System notes
Thank you for purchasing your Acer server. This user guide is intended as a reference for
experienced server technicians and helps detail many of the features available in Acer
servers. For more detailed information about any particular component or software solution,
you may consult the technical specifications or the user manuel for that application.
Note: Before opening or removing any components
please contact your local certified Acer service
representative
Warning: Any parts or components damaged
during replacement by a non-certified technician
are not covered by the warranty. For details,
please consult the warranty guide from your system.
System component identification
Front View:
Rear View
Rear I/O Panel
System controls and indicators
Front panel controls
Function
Description
Power On/Off Button
This is the main power button, which is used to apply
or turn off the main system power. Turning off system
power with this button removes the main power but
keeps standby power supplied to the system.
System Reset Button
Use the reset button to reboot the system.
Power LED
Indicates power is being supplied to the system's
power supply. This LED should normally be on when
the system is operating.
HDD Activity LED
Indicates hard disk drive activity when flashing.
LAN1 Network Activity
LED
Indicates network activity on LAN1 when flashing.
LAN2 Network Activity
LED
Indicates network activity on LAN2 when flashing.
Information LED
Power Fail
This LED functions only when two power supply
modules have been installed in the system and
indicates a power supply module has failed (when
illuminated).
Setting up the system
Pre-installation requirements
Selecting a site
Before unpacking and installing the system, select a suitable site for the system for
maximum efficiency. Consider the following factors when choosing a site for the system:
⚫Near a grounded power outlet.
⚫Clean and dust-free
⚫Stable surface free from vibration.
⚫Well-ventilated and away from sources of heat.
⚫Secluded from electromagnetic fields produced by electrical devices such as air
conditioners, radio and TV transmitters, etc.
Checking the package contents
Check the following items from the package:
⚫System unit
⚫Accessory box
If any of the above items is damaged or missing, contact your dealer immediately.
Save the boxes and packing materials for future use.
Turning on the system
After making sure that you have properly set up the system, applied power and connected
all the necessary peripherals, you can now power on the system. Follow the procedure
below.
Press the power button 。
The system starts up and displays a welcome message on the monitor. After that, a series
of power-on self-test (POST) messages appears. The POST messages indicate if the
system is running well or not.
Note: If the system does not turn on or boot after
pressing the power button, go to the next section
for the possible causes of the boot failure
Aside from the POST messages, you can determine if the system is in good condition by
checking if the following occurred.
⚫The power status indicator on the front panel lights up blue.
⚫The Num Lock, Caps Lock and Scroll Lock indicators on the keyboard light up.
Power-on problems
If the system fails to boot after you have applied power, check the following factors that
might have caused the boot failure.
⚫The external power cord may be loosely connected.
⚫Check the power cord connection from the power outlet to the power cord socket on
the rear panel. Make sure that the cord is properly connected to the power outlet and to
the power cord socket.
No power comes from the grounded power outlet. Have an electrician check your
power outlet.
⚫Loose or improperly connected internal power cables.
Check the internal cable connections. If you are not confident to perform this step, ask
a qualified technician to assist you.
Warning! Make sure all power cords are
disconnected from the electrical outlet before
performing this task.
Note: If you have gone through the preceding
actions and the system still fails to boot, ask your
dealer or a qualified technician for assistance.
Turning off the system
There are two ways to turn off the server—via software or via hardware. The software
procedure below applies to a system running on a Windows OS. For other shutdown
procedures, refer to the related user documentation.
To turn off the system via software:
1. Press <Ctrl> + <Alt> + <Delete> on the attached keyboard or click Start on the
Windows taskbar.
2. Select Shut Down.
3. Select Shut Down from the drop-down menu, then click OK.
To turn off the system via hardware
If you cannot shut down the server via software, press the power button for at least four
seconds. Quickly pressing the button may put the server in a Suspend mode only.
System troubleshooting
Resetting the system
Before going through in-depth troubleshooting, attempt first to reset the system using one
of the methods below.
Perform
Purpose
To do this
Soft boot
To clear the system memory and
reload the operating system.
Press <Ctrl> + <Alt> + <Del>
Cold boot
To clear the system memory, restart
POST, and reload the operating
system. This will halt power to all
peripherals.
Turn the system off and then on
again.
Initial system startup problems
Problems that occur at initial system startup are usually caused by an incorrect installation
or configuration. Hardware failure is a less possible cause. If the problem you are
experiencing is with a specific application.
Initial troubleshooting checklist
⚫AC power is available at the wall outlet?
⚫Is the power supply module properly installed?
⚫Is the system power cord properly plugged into the power supply module socket? and
connected to a NEMA 5-15R outlet for 100-120 V or a NEMA 6-15R outlet for 200-240
V?
⚫Are all peripheral cables correctly connected and secured?
⚫Did you press the system power button to turn the server on (power on indicator should
be lit green)?
⚫Are all device drivers properly installed?
⚫Are hard disk drive(s) properly formatted and configured?
⚫Are the BIOS configuration settings in the BIOS Setup Utility correct?
⚫Is the operating system properly loaded?
Refer to the operating system documentation.
⚫Are all hardware components compliant with the tested components
⚫lists?
⚫Are all internal cables correctly connected and secured?
⚫Is the processor properly seated in its mainboard socket?
⚫Are all standoffs in the proper location and not touching any components, causing a
potential short?
⚫Are all add-in expansion cards fully seated in their mainboard slots?
⚫Are all system jumpers correctly set?
⚫Are all switch settings on add-in boards and peripheral devices correct?
To check these settings, refer to the manufacturer’s documentation that comes with
them. If applicable, ensure that there are no conflicts (e.g., two add-in boards sharing
the same interrupt).
Tabla de contenidos
Otros manuales de Servidor de Acer
Acer
Acer Altos R720 Series Manual de usuario
Acer
Acer AR160 F1 Series Manual de usuario
Acer
Acer Altos R920 Series Manual de usuario
Acer
Acer Altos R720 Series Manual de usuario
Acer
Acer AR320 F2 Manual de usuario
Acer
Acer AC100 Manual de usuario
Acer
Acer Veriton 9100 Manual de usuario
Acer
Acer Altos R480 F4 Manual de usuario
Acer
Acer Altos R510 Manual de usuario
Acer
Acer Altos R920 Series Manual de usuario
Acer
Acer ALTOS R910 Series Manual de usuario
Acer
Acer Altos R310 Manual de usuario
Acer
Acer Extensa 500 Manual de lista de piezas
Acer
Acer AR320 Manual de usuario
Acer
Acer Altos G710 Manual de usuario
Acer
Acer AT150 F1 Series Manual de usuario
Acer
Acer HDS AMS200 Manual de usuario
Acer
Acer Altos R710 Manual de usuario
Acer
Acer AC100 Manual de usuario
Acer
Acer Altos G700 series Manual de usuario
