Absco PPCK Guía de instalación
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
EXTERNAL BASE DIMENSIONS: 1520mm x 1520mm
EXTERNAL REAR WALL HEIGHT: 1490mm
EXTERNAL FRONT WALL HEIGHT: 1220mm
RECOMMENDED CONCRETE
SLAB SIZE: 1620mm x 1620mm x
100mm THICK
We thank you for choosing an Australian made
shed. For further assistance please visit our detailed
instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be
number ONE, so please let us know what you think
of our instructions. Feedback makes us better.
CONCRETE
REBATED EDGE
BOTTOM CHANNEL
CONCRETE SLAB
75mm WIDE REBATE
100mm
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEP
AROUND THE PERIMETER
THIS WILL HELP WATER EGRESS
FROM THE BASE OF THE SHED
Absco Industries
Pool Pump Cover: PPCK
PAGE 01
GENERAL INSTRUCTIONS
A NOTE ON SAFETY
·The site for the shed must be level. An uneven surface may result in misalignment of
parts.
·It is recommended that the shed be set on a 100mm concrete slab and anchored down
appropriately (refer to last page for details).
·Anchor sets are not supplied as standard items with this product as some customers
wish to use their own anchoring systems.
·Before commencing any assembly, read through these instructions in
detail to gain a thorough understanding of assembly methods and
associated details.
·Unpack the carton and carefully identify and check off all the parts
against the parts described and illustrated on pages three and four.
·Some parts may have sharp edges. It is advisable to wear gloves when
handling these items and safety glasses if drilling holes. Sensible shoes
are highly recommended.
·Do not erect your shed in windy conditions, ensure that the shed is
securely anchored to a solid foundation immediately after construction is
completed.
·It is highly recommended to erect the shed with two or more people.
TOOLS REQUIRED
SITE PREPARATION
TOOLS OPTIONAL
10mm
(Steel)
10mm
(Masonary)
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 02
COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS
2
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY QTY
PPB
1
1
1
1
2
1
1
PPG
1
2
2
4
1
1
PPA
PPC
57A
CHANNEL
L = 1513mm
53B
CHANNEL
L = 1513mm
81N
CHANNEL
L = 1528mm
79C
CHANNEL
L = 783mm
64C
STEEL SHEET
1460mm X 773mm
STEEL SHEET
1330mm X 773mm
STEEL SHEET
1460mm X 773mm
STEEL SHEET
1460mm X 773mm
STEEL SHEET
1330mm X 773mm
STEEL SHEET
1622mm X 773mm
PPL
PPD
PPR
STEEL SHEET
1140mm X 773mm
64A
64B
81F
CHANNEL
L = 1513mm
CHANNEL
L = 1513mm
81E
CHANNEL
L = 1200mm
1
1
CHANNEL
L = 1140mm
CHANNEL
L = 1140mm
1PPF
STEEL SHEET
1203mm X 711mm
1
58C
CHANNEL
L = 773mm
2
91A
JAMB L= 1120mm
57A
53B
58C
64B
64A
64C
79C
81E
1
JAMB L= 1100mm
94C
81N
81F
Part No. Here
Part No. Here
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 03
30 CSK SCREW & NUTS
3mm POP RIVETS
1ASSEMBLY
INSTRUCTIONS
COMPONENT
DESCRIPTION
PART
No. CHECK COMPONENT
DESCRIPTION
PART
No. CHECK
QTY QTY
INSTRUCTIONS & FITTINGS PACKET
12A
1
DOOR
STRAP
L: 165mm
1
1
1
2
2
4
JAMB L= 783mm
JAMB L= 1203mm
JAMB L= 1203mm
JAMB L= 1480mm
90C
94A
94B
94D
88C
LIP TRIM L= 1622mm
88D
LIP TRIM L= 230mm
8Gx20mm
SELF TAPPING
SCREWS
5
30
BUTT
HINGES
5
122C
PRE-PUNCHED
PADBOLT
SUPPORT PLATE
88C
88D
Part No. Here
Part No. Here
Part No. Here Part No. Here
1PSTKDBL
DOUBLE DOOR
FITTINGS PACK
DOOR
PADBOLT
HASP
2
3
SELF TAPPING SCREWS
PACKET CONTAINING 220
1
DOOR
PADBOLT
3/16 COUNTERSUNK
SCREWS & NUTS
12
3/16 ROUND HEAD
BOLTS & NYLOCK NUTS
83.2 x 8mm
BLIND POP RIVETS12
PSTKDBL - DOUBLE DOOR FITTINGS PACK
PACK12P - SCREW PACK 12
PACK12P
SCREW PACK 12
1
PHILLIPS DRIVER BIT
3mm DRILL BIT
1 1
DRILL FAST038
FAST007FAST006
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 04
NOTE: YOU WILL FIND THAT MOST HOLES
REQUIRED HAVE BEEN PRE-PUNCHED.
A 3mm DRILL BIT IS SUPPLIED FOR DRILLING
HOLES WHERE PRE-PUNCHING WAS NOT
POSSIBLE.
LEFT
SIDE
PANEL
RIGHT
SIDE
PANEL
22A
22C
81E
88C
PPA
PPA
94D
94D
88D
81E
PPG
81E
64C
PPL
90C
PPD
PPR
94A
22A
PPB
88C
94C
PPB
81F
81N
PPF
81N
94B
79C
53B
91A
12A 58C
64A
81E
58C
64B
PPC
57A
81F
VIEW OF ROOF AND WALL COMPONENTS
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 05
ABSCO ASSEMBLY INTRODUCTION
FASTENING SYMBOLS
The snaptite assembly system locks most perimeter channels to all roof and wall
sheets without the need for tools and fasteners.
To pre-assemble the four wall panels
and two roof panels, the perimeter
channels are secured to the top and
bottom of each panel using the
snaptite system, as detailed on the
following pages wherever you see
the symbol.
Position sheets on timbers,
trestles or partly over edge of
concrete slab.
Each perimeter channel must finish flush with the
edges of the sheets.The snaptite system allows
adjustment for this process by simply tapping the
channel along the sheets until each end is neatly
flush. If you need to remove channels from the
panels, pull the channel along the panel from
opposing ends. You may need someone to help
with this.
Join components together with one screw at this
location only, as some channel sections have extra
holes that are not required for this model of garden
shed
Do not join components together at this location yet,
as the screw may obstruct further assembly of other
components
4mm NUT & BOLT SET
3mm POP RIVETS
PUSH
PUSH
HIGH SIDE
HIGH SIDE
PUSH
HIGH SIDE
HIGH SIDE
After joining sheets together, position channel over one end of the sheets, gently
tapping it over the snaptite lugs, working along the sheets to the other end.
HIGH SIDE
SNAP
T TE
i
SNAP
T TE
i
SNAP
T TE
i
Join components together by pre-drilling the holes
first. Use one component as a template to mark where
the holes are. Drill with 3mm drill bit.
D
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 06
SNAP
T TE
i
SNAP
T TE
i
81F
81F
PPB
PPB
1. REAR PANEL ASSEMBLY NOTE: JOIN TOGETHER AT
PRE-PUNCHED LOCATIONS
AS SHOWN.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 07
2. LEFT PANEL ASSEMBLY NOTE: JOIN ALL FIVE COMPONENTS TOGETHER
AT PRE-PUNCHED LOCATIONS AS SHOWN.
1460
1330
1200
SNAP
T TE
i
SNAP
T TE
i
81N
PPG
PPL
81E
64C
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 08
SNAP
T TE
i
SNAP
T TE
i
PPR
PPD
81E
81N
1460
1200
1330
3. RIGHT PANEL ASSEMBLY NOTE: JOIN TOGETHER AT
PRE-PUNCHED LOCATIONS
AS SHOWN.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 09
4. LID PANEL ASSEMBLY
NOTE: PART 88C
IS A PIECE OF
ANGLE FLASHING
1622mm LONG.
PPA
PPA
81E
88C
88C
81E
SNAP
T TE
i
SNAP
T TE
i
NOTE: JOIN TOGETHER AT
PRE-PUNCHED LOCATIONS
AS SHOWN.
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: PPCK 22-11-2017
Absco Industries
Pool Pump Cover: PPCK
PAGE 10
Tabla de contenidos
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
