abem Terrameter LS Manual de usuario
User Manual
Terrameter LS Toolbox
ABEM Product Number 33 3100 08
ABEM 2016-12-07, based on release 2.0.1 of Terrameter LS Toolbox
ABEM Terrameter LS Toolbox
ABEM Terrameter LS Toolbox
Thank you for choosing ABEM Terrameter LS Toolbox
Trademarks
Microsoft®and Windows®are registered trademarks of Microsoft Corporation.
All other trademarks belong to their respective holder.
General information
Information in this manual is subject to change without notice and constitutes no commitment
by ABEM Instrument AB.
ABEM Instrument AB takes no responsibility for errors in this manual or problems that may
arise from the use of this material.
In general, e-mail correspondence gives the fastest response.
In view of our policy of progressive development, we reserve the right to alter specifications
without prior notice.
ABEM will be pleased to receive occasional reports from you concerning the use and
experience of the equipment and software. We also welcome your comments on the contents
and usefulness of this manual. In all communication with ABEM be sure to include the
instrument types and serial numbers and software versions.
Contact details:
Address:
ABEM Instrument AB
Löfströms Allé 6A
SE-17266 Sundbyberg
Sweden
Phone:
+46 8 564 88 300
Web site:
www.guidelinegeo.com
Email:
© Copyright 2016 ABEM Instrument AB. All rights reserved.
ABEM Terrameter LS Toolbox
i
ABEM Terrameter LS Toolbox
ii
Table of Contents
Section Page
1Introduction..........................................................................................................1
2Installation............................................................................................................2
3Overview...............................................................................................................6
4Instrument Communication and Management.................................................8
Initiating Communication..............................................................................8
Importing Data.............................................................................................10
Spread and Protocol Transfer.......................................................................11
Firmware Update .........................................................................................14
4.4.1 Updating the application software ...........................................................14
4.4.2 Updating the current transmitter firmware ..............................................15
Setting Timezone and Time.........................................................................17
5Data Management and Post-Processing...........................................................20
Project Management ....................................................................................20
Task Data Post-Processing...........................................................................22
5.2.1 Table ........................................................................................................24
5.2.2 Export.......................................................................................................26
5.2.3 View Electrode Contact Test ...................................................................26
5.2.4 Show on Map...........................................................................................27
5.2.5 View Pseudosection.................................................................................28
5.2.6 Full Waveform.........................................................................................31
5.2.7 View IP Decay Curves.............................................................................33
5.2.8 Edit Electrode Coordinates ......................................................................34
6Main Menu .........................................................................................................36
Conversion of ADR to XML Spread File....................................................37
Conversion of ORG to XML Protocol file ..................................................39
View Spread and Protocol ...........................Error! Bookmark not defined.
Windows Display.........................................................................................41
ABEM Terrameter LS Toolbox
iii
ABEM Terrameter LS Toolbox
1
1 Introduction
Terrameter LS Toolbox is a revised replacement for the Terrameter LS Utility
Software. The Terrameter LS Toolbox can be found and downloaded from
www.guidelinegeo.com .
The following functions are included:
Transfer of data files Terrameter LS => PC
Viewing, culling and export of data file contents via table
Listing contents of project data base files
Export of data files in different formats
Plotting of electrode contact resistances
Viewing the location of the survey on map
Plotting data as pseudo sections
Plotting of IP decay curves
Plotting of full waveform data sweeps
Export of full waveform data to TXT files
Transfer of spread and protocol files PC <=> Terrameter LS
Conversion of address files from the SAS4000 system into XML format
Conversion of protocol files from the SAS4000 system into XML format
Update of instrument software
Essentially everything is based around the tree structure on the left side and the
functions are accessed via a popup menu that appears when right clicking on an item.
ABEM Terrameter LS Toolbox
2
2 Installation
Note! Operating systems such as Windows 7, 8, 8.1 and 10 might have
limited access and permission to the “C:\Program Files” and “C:\Program Files
(x86)” folders, which might cause errors. To avoid issues it could be recommended
to install the Terrameter LS Toolbox in another folder, e.g. “C:\ABEM\Terrameter\”
The Terrameter LS Toolbox installer is available for download from www.abem.se.
The installation process is a matter of following a few simple steps.
When the installation program is run, the following dialog first appears:
Click Next.
The default installation folder can be accepted or changed. To change click Browse…
or type directly in the text field.
Click Next.
ABEM Terrameter LS Toolbox
3
The default Start Menu shortcut can be accepted or changed. To change click
Browse… or type directly in the text field.
Click Next.
Choose if a desktop icon shall be created or not.
Click Next.
ABEM Terrameter LS Toolbox
4
The installation process is now ready to start.
Click Install.
The installation is executed.
Otros manuales para Terrameter LS
1
Tabla de contenidos
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
