Abelko IMSE UltraBase40 Manual de usuario
www.abelko.se
IMSE
UltraBase40
Welcome to Ultra!
All users of this product must carefully read the manual and take
necessary safety precautions.
Safety instructions
If the product is not used as intended its protection and safety functions may
not work.
Installation
The unit is to be mounted on a DIN rail in a locked cabinet. Installation is
carried out by a qualied electrician. Cables must be fastened and secured so
that no risk for injury or re exists. Ventilation openings in the devise housing
may not be covered.
A circuit breaker shall be installed close to the unit and its power supply.
Function and position shall be clearly labelled. External voltage source
connected to DIGITAL OUT must be limited to a maximum of 0.5 A.
The equipment must be unplugged from the mains and other possibly
dangerous voltage sources during installation and service.
Quick start guide
www.abelko.se
Power supply
UltraBase40 can be powered in several ways. Requirements and characteristics
of the unit’s inputs and outputs can be found in the table below.
Port Supply
Supply expansion
module
(port Ex)
24 V out
(port Out)
(out +12V)
(in +12V**) 12 VDC* (>300 mA) No No Not
available
VDC 24 VDC* (>300 mA) 24 VDC, 1A 24 VDC,
100 mA
12 VDC,
100 mA
24V
24 VAC (>300 mA) No No 12 VDC,
100 mA
24 VDC* (>300 mA) No No 12 VDC,
100 mA
* Stabilized DC voltage.
** Use GND from the port Out.
The Power LED lights up when the device is energized and the Status LED
lights up when the device has started up and is working.
Safety instructions
All external equipment connected to the device must have double or
enhanced isolation (class II) from power mains or other dangerous
voltage source (>50 VAC or > 75 VDC).
Note that all cables used must be approved for at least 50 °C ambient
temperature.
At high ambient temperatures there is a risk for burning injuries. Wait
for the equipment to cool down, and use protective gloves.
Network connection
The unit is connected to a permanent network by the Ethernet port. The
factory default IP address is 10.0.48.94.
Local PC is used only to connect the unit directly to a PC. It has IP address
192.168.142.1, and can be used to congure the regular network connection
in the UltraBase40.
When you use the Local PC port, the computer should be congured for DHCP
(which it usually is).
1. Open a web browser and enter the IP address https://192.168.142.1 in
the address bar. This will take you to the login page.
User name and password the rst time you log in:
www.abelko.se
User name: cong
Password: ef56
2. Go to the menu Communication and Network, and set the IP
address and netmask, in order to congure the settings for the port
marked Ethernet.
You can also use DHCP, the unit will then automatically get network
settings. After a while, you can see which IP address it received. You
can use this IP address to access the device from a PC, connected to the
same network.
HTTPS
The rst time that you log in to an Ultra, you will be warned that the
connection is not private, secure, or similar. This is because the system uses
HTTPS for a secure and encrypted connection. The security is guaranteed by a
certicate that is issued for a specic address. Since the address is adjustable,
there is only a self-signed certicate for the unit.
You need to accept and add this exception. The procedure diers depending on
which browser you are currently using. The communication is still encrypted, so
no-one can see, for example, which passwords are being used.
Graphical programming
Graphical programming is available as an installable program. Download it at
www.abelko.se.
There is also a link to the program in your units user interface under
Conguration and Graphical programming.
Analog outputs
There are eight analog outputs for 0-10 V, marked
AO.
The gure to the rigth is an example on how you
can connect an AC-powered valve controller.
Digital outputs
There are eight digital outputs marked DO. These are open drain outputs with
breaking capacity 0,5 A and 24 VDC at resistive load.
Temperature sensor inputs
There are eight inputs for resistive temperature sensors marked with T. They
have a measurement range 800 till 1580 Ohm and works for example with
PT1000 sensors (approximately -50ºC till 150ºC) and Ni1000 sensors.
www.abelko.se
Analog inputs
There are eight analog inputs marked AI. Input 1-4 can measure 0-10 V. Input
5-8 can measure 0-20 mA.
Digital inputs
There are eight digital inputs marked DI. Digital inputs can be used for
digital status. In addition to this, inputs 1-4 can be used as counters and for
frequency measurement.
Cleaning
The housing is cleaned from dust and dirt using a dry cloth. Do not use
chemicals.
Recycling
UltraBase40 should be recycled as electronics.
Repair and service
Reparation and service shall always be performed by Abelko Innovation.
Contact your distributor rst if the need arises.
Manuals, updates and other information are available at
www.abelko.se.
Active 1-10 V sensor
4-20 mA sensor
Tabla de contenidos
