ABB SPACOM 300 Manual de usuario

Tabla de contenidos

Otros manuales de Relé de ABB

Manuales populares de Relé de otras marcas

Shelly

Shelly Pro Series Manual de usuario

GE

GE MVAX 11 Manual de usuario

Pilz

Pilz PNOZ X10 Manual del propietario

Kemo Electronic

Kemo Electronic B197 Manual de usuario

Seg

Seg MRM3 Manual de usuario

Basler

Basler BE1-700C Manual de usuario

CD Automation

CD Automation REVEX 2PH 280A Manual de usuario

Ruelco

Ruelco 1S04 Manual de usuario

Basler

Basler V3E Z1P B2C1F Manual de usuario

Doepke

Doepke Dupline DSM 2 Manual de usuario

Siemens

Siemens SIRIUS 3RT1966-4D Manual de usuario

GE

GE DGP Manual de usuario

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Manual de usuario

Siemens

Siemens SIPROTEC 4 Manual de usuario

Siemens

Siemens BD2-AK03X/FS Series Manual de usuario

Leuze

Leuze MSI-SR5B Manual de usuario

Littelfuse

Littelfuse SE-330AU Manual de usuario

EVA Logik

EVA Logik ZW12 Manual de usuario

—

Relay Retrofit Program

Cutting Tool

Operating Guide SPACOM 300

2RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300

—

Table of contents

03 1. Preparations

03 2. Cutting cycle

04– 05 3. Operating the cutting tool on

a horizontal edge

06 4. Install the cover plate

06 5. Finishing your work

RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300 3

—

1. Preparations

Remove the existing relay.

Ensure that there is enough space to operate

the cutting tool in all intended directions.

Check the space required by the replacement

IED and its wiring.

Place the cover plate in its intended location.

Mark the outline for the opening and the fixing screw

locations in each corner of the cover plate.

Drill the holes for fixing screws using a drill bit

of 4.5 mm in diameter.

1.1

1.2

—

2. Cutting cycle

Horizontal: 1, 4, 3 and 2.

Min. 171

214

139

4RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300

—

3. Operating the cutting tool on a horizontal edge

Ensure that the cutting head is set in the correct

position. The text HORIZONTAL Up and Down must

point in the direction you are cutting.

Make four punches, side by side.

Ensure that you use the correct guiding,

before each cutting cycle.

After each cutting cycle, ensure that thecutting head

is clear of offcut!

3.1

3.2

3.3

RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300 5

Push the vent lever to release the punch

after each cutting cycle.

For your safety, keep your hands on the power unit,

never on the cutting head.

Beware of the sharp edges!

Note the cutting order. Cut the parts next to

the edges first and the middle part last.

3.4

3.5

3.6

6RELAY RETROFIT PROGRAM CUTTING TOOL OPERATING GUIDE SPACOM 300

—

5. Finishing your work

Finish your work and install the new IED.

Clean the offcuts from the floors.

5.1

—

4. Install the cover plate

Close the door and install the cover plate.

Use the self-tapping screws supplied with

the cover plate.

4.1

7

—

Notes

1MRS757999 REV C EN 3-2019

© Copyright 2019 ABB. All rights reserved.

Specifications subject to change without notice.

Additional information

We reserve the right to make technical changes or

modify the contents of this document without prior

notice. With regard to purchase orders, the agreed

particulars shall prevail. ABB does not accept any

responsibility whatsoever for potential errors or

possible lack of information in this document.

We reserve all rights in this document and in the

subject matter and illustrations contained therein.

Any reproduction, disclosure to third parties or

utilization of its contents – in whole or in parts – is

forbidden without prior written consent of ABB.

—

For more information, please contact

E-Mail: af[email protected]

abb.com/service

abb.com/mediumvoltage