ABB REB650 Manual de usuario
RELION® 650 SERIES
—
DNP, 650 series
Version 2.2
Point list manual
Document ID: 1MRK 511 419-UUS
Issued: October 2017
Revision: A
Product version: 2.2.1
© Copyright 2017 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third party,
nor used for any unauthorized purpose.
The software and hardware described in this document is furnished under a license and
may be used or disclosed only in accordance with the terms of such license.
This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/) This product includes cryptographic
software written/developed by: Eric Young ([email protected]) and Tim Hudson
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or
product description and are not to be deemed as a statement of guaranteed properties.
All persons responsible for applying the equipment addressed in this manual must
satisfy themselves that each intended application is suitable and acceptable, including
that any applicable safety or other operational requirements are complied with. In
particular, any risks in applications where a system failure and/or product failure would
create a risk for harm to property or persons (including but not limited to personal
injuries or death) shall be the sole responsibility of the person or entity applying the
equipment, and those so responsible are hereby requested to ensure that all measures
are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested to
notify the manufacturer. Other than under explicit contractual commitments, in no
event shall ABB be responsible or liable for any loss or damage resulting from the use
of this manual or the application of the equipment.
Conformity
This product complies with the directive of the Council of the European Communities
on the approximation of the laws of the Member States relating to electromagnetic
compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for
use within specified voltage limits (Low-voltage directive 2006/95/EC). This
conformity is the result of tests conducted by ABB in accordance with the product
standard EN 60255-26 for the EMC directive, and with the product standards EN
60255-1 and EN 60255-27 for the low voltage directive. The product is designed in
accordance with the international standards of the IEC 60255 series and ANSI C37.90.
The DNP protocol implementation in the IED conforms to "DNP3 Intelligent
Electronic Device (IED) Certification Procedure Subset Level 2", available at
www.dnp.org.
Table of contents
Section 1 Introduction............................................................................3
This manual.............................................................................................. 3
Intended audience.................................................................................... 3
Product documentation.............................................................................4
Product documentation set..................................................................4
Document revision history................................................................... 5
Related documents..............................................................................6
Document symbols and conventions........................................................ 7
Symbols...............................................................................................7
Document conventions........................................................................ 8
Section 2 DNP3 data mappings.......................................................... 11
Overview.................................................................................................11
Point list for the IEDs.............................................................................. 11
Section 3 DNP3 protocol implementation............................................27
DNP3 device profile................................................................................ 27
DNP3 implementation table.................................................................... 71
Section 4 Glossary.............................................................................. 79
Glossary..................................................................................................79
Table of contents
650 series 2.2 ANSI 1
Point list manual
2
Section 1 Introduction
1.1 This manual
GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v18
The point list manual describes the outlook and properties of the data points specific to
the IED. The manual should be used in conjunction with the corresponding
communication protocol manual.
1.2 Intended audience
GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v11
This manual is intended for the communication system engineer or system integrator
responsible for pre-engineering and engineering the communication setup in a
substation from an IED perspective.
The system engineer or system integrator must have a basic knowledge of
communication in protection and control systems and thorough knowledge of the
specific communication protocol.
1MRK 511 419-UUS A Section 1
Introduction
650 series 2.2 ANSI 3
Point list manual
1.3 Product documentation
1.3.1 Product documentation set GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v15
IEC07000220-4-en.vsd
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
Deinstalling & disposal
Application manual
Operation manual
Installation manual
Engineering manual
Communication
protocol manual
Cyber security
deployment guideline
Technical manual
Commissioning manual
IEC07000220 V4 EN-US
Figure 1: The intended use of manuals throughout the product lifecycle
The engineering manual contains instructions on how to engineer the IEDs using the
various tools available within the PCM600 software. The manual provides instructions
on how to set up a PCM600 project and insert IEDs to the project structure. The
manual also recommends a sequence for the engineering of protection and control
functions, LHMI functions as well as communication engineering for IEC
60870-5-103, IEC 61850, DNP3, LON and SPA.
The installation manual contains instructions on how to install the IED. The manual
provides procedures for mechanical and electrical installation. The chapters are
organized in the chronological order in which the IED should be installed.
Section 1 1MRK 511 419-UUS A
Introduction
4650 series 2.2 ANSI
Point list manual
Otros manuales para REB650
2
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Dispositivo de protección de ABB
ABB
ABB relion REF615 Manual de usuario
ABB
ABB REM 610 Manual del producto
ABB
ABB RELION RET670 Manual de usuario
ABB
ABB Relion 630 Series Instrucciones de uso
ABB
ABB REQ650 1.3 IEC Guía de inicio rápido
ABB
ABB Relion 670 series Instrucciones de uso
ABB
ABB RELION RET670 Instrucciones de uso
ABB
ABB REG316 4 Series Manual de usuario
ABB
ABB REM615 ANSI Manual de usuario
ABB
ABB Relion REB500 Manual de usuario
ABB
ABB Relion REB500 Manual de instalación y operación
ABB
ABB Relion 620 Series Instrucciones de uso
ABB
ABB REL650 series Manual de usuario
ABB
ABB REG650 ANSI Manual de usuario
ABB
ABB MDAR Manual de usuario
ABB
ABB Relion REB500 Manual de usuario
ABB
ABB REF601 Manual de usuario
ABB
ABB Relion 670 series Guía de inicio rápido
ABB
ABB Relion 650 Series REL650 Guía de inicio rápido
ABB
ABB REM615 ANSI Hoja de datos
