ABB OHDI-01 Manual de usuario

DriveIT Low Voltage AC Drives

User’s Manual

115/230 V Digital Input Module

OHDI-01

OHD4

2 115/230 V Digital Input Module – OHDI-01

Safety

WARNING! All electrical installation and maintenance work on the

drive should be carried out by qualified electricians only.

WARNING! The drive and adjoining equipment must be properly

grounded.

WARNING! Do not attempt any work on a powered drive. After

switching off the mains, always allow the intermediate circuit

capacitors 5 minutes to discharge before working on the drive, the

motor or the motor cable. It is good practice to check (with a

voltage indicating instrument) that the drive is in fact discharged

before beginning work.

WARNING! The motor cable terminals of the drive are at a

dangerously high voltage when mains power is applied,

regardless of motor operation.

WARNING! There can be dangerous voltages inside the drive from

external control circuits even when the drive mains power is shut

off. Exercise appropriate care when working on the unit.

Neglecting these instructions can cause physical injury or death.

Use of Warnings and Notes

There are two types of safety instructions throughout this manual:

• Notes draw attention to a particular condition or fact, or give

information on a subject.

• Warnings caution you about conditions which can result in serious

injury or death and/or damage to the equipment. They also tell you

how to avoid the danger. The warning symbols are used as follows:

Dangerous voltage warning warns of high voltage which can

cause physical injury and/or damage to the equipment.

115/230 V Digital Input Module – OHDI-01 3

Table of Contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Use of Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installing the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 115/230 V Digital Input Module – OHDI-01

Installation

Preparing for Installation

The OHDI-01 Module

The 115/230 V Digital Input module (OHDI) is an interface for

connecting six high voltage digital inputs to an ACS550 or ACH550

drive. The OHDI accepts 115 or 230Volt inputs andconvertsthem to 24

VDC for the drive. The input can be either of the following:

• Up to six 115 Volt inputs

• Up to three 230 Volt inputs

Module Layout

Compatibility

The OHDI-01 is compatible with all ACS550, ACH550 and ACS800

drives.

24 VDC 115/230

OHD4

Outputs (6) Digital Inputs

High Side

Low Side

115/230 V Digital Input Module – OHDI-01 5

Installation

Installing the Module

Delivery Check

The option package contains:

• OHDI-01 module

• two mounting screws

• This manual

Mounting

WARNING! Follow the safety instructions given in this guide and in the

drive manual: ACS800 Hardware Manual, ACS550 User’s Manual or

ACH550 User’s Manual.

To mount the OHDI-01

module:

1. If not already off,

remove mains power

from the drive.

2. Remove the drive

cover. (See

instructions in the

drive User’s Manual.)

3. Position the OHDI-01

module on the front of

the drive:

• ACS800: at

Optional Module 1

or Optional

Module 2.

• ACS550/ACH550:

at SLOT 2.

4. Attach using the two mounting screws provided.

Screws

OHD

6 115/230 V Digital Input Module – OHDI-01

Installation

Wiring

Connect 115/230V inputs to the OHDI inputs and connect OHDI 24V

outputs to the drive digital inputs.

For wiring, use:

• Appropriate voltage rated wiring (115 or 230 V) for the inputs to the

high side.

• 0.5 to 1.5 mm2(20 to 16 AWG) cable with 24 V rating for connections

between the low side and the drive terminals.

To determine the proper routing for wiring, refer to the following

sources:

• The "TerminalDesignations" section below forthe OHDI-01 module’s

terminal designations.

• The drive’s terminal designations in the appropriate manual:

- ACS550 User’s Manual

- ACH550 User’s Manual

- ACS800 Hardware Manual

• The table below for alternatives.

• The diagram below for an overview of the connections.

• The illustrations below for a view of typical wiring connections.

Alternatives:

Situation Wiring

All digital inputs are from 115 or

230 V sources. Connect inputs according to the above

diagram. Use as many as required (up to 3

230V inputs or up to 6 115V inputs).

Digitalinputsare from a mixture of

low voltage (10 to 24 VDC)

sources and high voltage (115 or

230 V) sources.

Route high voltage digital inputs through OHDI

module.

Route low voltage digital inputs directly to X1

on the drive.

115/230 V Digital Input Module – OHDI-01 7

Installation

Connections overview:

The following illustration shows a sample of typical wiring.

OHDI-01

Module

14 (L/N)

8 (HDI1)

9 (HDI2)

10 (HDI3)

11 (HDI4)

12 (HDI5)

13 (HDI6)

115/230V

Source

7 (LDI6)

1 (24V/GND)

2 (LDI1)

3 (LDI2)

4 (LDI3)

5 (LDI4)

6 (LDI5)

ACH550

11 (GND)

10 (+24V)

18 (DI6)

12 (DCOM)

13 (DI1)

14 (DI2)

15 (DI3)

16 (DI4)

17 (DI5)

Normal (Sourcing)

Configuration ACS800

X22

6 (DI6)

1 (DI1)

2 (DI2)

3 (DI3)

4 (DI4)

5 (DI5)

OHDI-01

Module

1 (24V/GND)

11 (GND)

10 (+24V)

12 (DCOM)

13 (DI1)

Alternate (Sinking)

Configuration

2 (H DI1)

7 (24V)

ACS550/

ACH550

ACS550/

15V only

Insert screwdriver in slot

above wire clip to open clip.

Drive

115V

Digita

Input

Digital

Inputs

24V wires

between

OHDI and

drive

OHD2

OHD3

8 115/230 V Digital Input Module – OHDI-01

Installation

Terminal Designations

Use the following table for reference when wiring terminals.

Replace Drive Cover

1. Refer to the drive’s User’s manual and replace the drive’s cover.

Apply Power

1. Turn on the mains power to the drive.

2. Refer to the Start-Up section in the drive’s User’s Manual for

configuration of digital inputs.

Identification Typical Connection

Low Side Digital Input Terminal

ACS550 / ACH550 ACS800

1 24 V / GND 10 (+24V) or 11 (GND) 7 (24V)

2LDI1 13 (DI1) 1 (DI1)

3LDI2 14 (DI2) 2 (DI2)

4LDI3 15 (DI3) 3 (DI3)

5LDI4 16 (DI4) 4 (DI4)

6LDI5 17 (DI5) 5 (DI5)

7LDI6 18 (DI6) 6 (DI6)

High Side External Digital Input Source

115V Source 230V Source

8HDI1

9HDI2

10 HDI3

11 HDI4

12 HDI5

13 HDI6

14 Line / Neutral 115

Source 230V

Source

115/230 V Digital Input Module – OHDI-01 9

Technical Data

Dimensions

Module dimensions

are:

Enclosure

Degree of Protection

The module is mounted inside the drive enclosure. Refer to the drive’s

rating.

Ambient Conditions

The module is mounted inside the drive enclosure. Refer to the drive’s

requirements.

Connectors

Connectors on the module:

• Low side: 6-pin, spring cage, non-detachable terminal block that

accepts wire connectors up to 1.5 mm2 (16 AWG).

• High side: 6-pin, spring cage, non-detachable terminal block that

accepts wire connectors up to 2.5 mm2 (14 AWG).

Ref. mm in

H35 1.4

L95 3.7

W62 2.4

OHD5

10 115/230 V Digital Input Module – OHDI-01

Technical Data

Specifications

Module Specifications

• Module is UL/CSA-approved.

• Module complies with EMC standards EN 50081-2 and EN 50082-2.

• Input voltage: 115 to 230 volts +10%

• Max. current leakage in digital off state: 2 mA.

• Isolation between low and high side terminals, test voltage: 2.5 kV

rms, 1 minute.

Otros manuales para OHDI-01

Tabla de contenidos

Manuales populares de Equipos industriales de otras marcas

Mark 7

Mark 7 Evolution Manual de usuario

Husky

Husky HyPET Manual de usuario

bora

bora PM-1800 Manual de usuario

Grizzly

Grizzly T32428 Manual de usuario

Siemens

Siemens 8MF1 Series Manual de usuario

Phoenix

Phoenix PHX-150 Manual de usuario

Rioned

Rioned UrbanJet Manual de usuario

Hermetica

Hermetica 10 Series Manual de usuario

HORNER

HORNER OEE Solution Manual de usuario

Hammerhead

Hammerhead HG375 Manual de usuario

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instrucciones de uso

Webasto

Webasto GSE CAN Manual de usuario

BAC

BAC BCP2D Manual de usuario

M&C

M&C SP Series Manual de usuario

Raven

Raven DCS 700 Manual

Maxcess

Maxcess FIFE D-MAXE 3 Manual de usuario

MachineryHouse

MachineryHouse SW4000 Manual de usuario

Dover

Dover Triton 9610 Manual de usuario