ABB ACH580-01 Series Manual de usuario

—

ACH580-01 BxR, UL Type 1/12

Frame R1/R2

Base drive replacement instructions

Purpose or Scope

The following are the instructions for replacing an ACH580-01 UL Type 1 and 12 (Frames

R1 & R2) drive in BxR enclosures.

Equipment required*:

– Replacement drive (see note below)

– T20 bit

– T30 bit

– PZ2 bit

– PZ3 bit

– Torque wrench

– Zip ties

Basic overview of steps

– Back-up drive parameters (if you can)

– Remove power and verify after 5 minutes

– Open enclosure

– Disconnect all wiring

– Remove flange plate

– Remove drive

– Prepare replacement drive

– Remove conduit assembly

– Install in reverse order

– Check connections

– Power drive

– Reprogram and test

Notes and cautions

CAUTION! Review complete safety and electrical considerations prior

to replacing the drive. See ACH580 IOM (3AXD50000049127).

CAUTION! Two people are recommended for this job. The drive is

heavy and can fall, causing property damage and injury.

NOTE: UL Type 12 drives require a UL Type 12 replacement drive,

UL Type 1 drives are not allowed as substitutes for UL Type 12.

* Not all of these tools are needed for each frame size.

2REPLACEMENT INSTRUCTIONS | ACH580-01 BXR UL TYPE 1 & 12, R1/R2

Step Instruction Diagram

1 NOTE: If needed, back-up parameters prior to disconnecting power.

Turn off source power and wait 5 minutes for the DC bus capacitors

to discharge.

Turn handle to the off position.

2 Rotate latches clockwise and open the enclosure door.

3 Perform voltage check to confirm no voltage is present.

NOTE: If you have control wiring connected to the Control Unit,

disconnect at this time.

3REPLACEMENT INSTRUCTIONS | ACH580-01 BXR UL TYPE 1 & 12, R1/R2

Step Instruction Diagram

4 Cut zip tie Aand remove the CDPI Bfrom drive. Set aside.

Cut zip tie Cand disconnect the RS485 cable Dfrom the drive

by pulling out the terminal block.

NOTE: Remove any additional drive I/O wiring.

5 Using a PZ2 bit, loosen and remove wires from the Input Terminals

of the drive.

Using a PZ2 bit, loosen and remove wires from the Motor Terminals

of the drive.

6 Using a PZ3 bit, loosen and remove ground wire from the drive.

7 Using a T20 bit, loosen and remove six (6) screws securing the

flange plate A.

Save hardware.

4REPLACEMENT INSTRUCTIONS | ACH580-01 BXR UL TYPE 1 & 12, R1/R2

Step Instruction Diagram

8 Using a T30 bit, loosen the four (4) M6 screws securing the drive,

four (4) turns of the screw.

NOTE: Do not remove the screw completely. Only loosen enough to

be able to lift the drive off the screws.

Carefully push the drive up, lift the drive off of the screws and out

of enclosure.

9 Unpack the replacement drive.

UL Type 12: UL Type 12 drives require a UL Type 12 replacement

drive, UL Type 1 are not allowed as substitutes for UL Type 12.

Remove drive cover by pushing up on the sides as indicated by

arrow.

Recycle drive cover.

UL Type 12: Recycle the hood that was included in the box and the

drive cover that was removed.

5REPLACEMENT INSTRUCTIONS | ACH580-01 BXR UL TYPE 1 & 12, R1/R2

Step Instruction Diagram

10 Using a T20 bit, loosen and remove two (2) M4x8 screws. Remove

conduit assembly.

Recycle the conduit assembly and hardware.

11 CAUTION! Use two people to install the drive.

Slide the drive mounting holes over the four (4) screws and slide

drive in place.

Torque all four (4) mounting screws to 27 in-lb (3 Nm).

6REPLACEMENT INSTRUCTIONS | ACH580-01 BXR UL TYPE 1 & 12, R1/R2

Step Instruction Diagram

12 Place collar around drive. Using a T20 bit, secure the drive using the

six (6) M4x20 screws that were removed earlier.

Using a T20 bit, torque to 14 in-lb (1.5 Nm).

13 Secure the ground wire to the drive.

Using a PZ3 bit, torque to 14 in-lb (1.5 Nm).

7REPLACEMENT INSTRUCTIONS | ACH580-01 BXR UL TYPE 1 & 12, R1/R2

Step Instruction Diagram

14 Connect the input wires (from fuse block) to the Input Terminals of

the drive.

Yellow U1 to L1

Black V1 to L2

Red W1 to L3

R1 Frame: Using PZ2 bit, torque terminals to 5 in-lb (0.5 Nm).

R2 Frame: Using a PZ2 bit, torque terminals to 14 in-lb (1.5 Nm).

15 Connect the motor wires (from 1M contactor) to Motor Terminals of

the drive.

Yellow U2 to T1/U

Black V2 to T2/V

Red W2 to T3/W

R1 Frame: Using PZ2 bit, torque terminals to 5 in-lb (0.5 Nm).

R2 Frame: Using a PZ2 bit, torque terminals to 14 in-lb (1.5 Nm).

16 Re-install the CDPI Ainto control unit and secure with two

zip ties B.

Reconnect the RS485 terminal block Cto EFB on control unit and

secure with two zip ties D.

Reconnect any control wiring removed in steps 3 and 4.

WARNING! This configuration does not support Safe Torque Off (STO)

functionality in bypass mode.

17 Close the door and rotate latches counterclockwise.

8REPLACEMENT INSTRUCTIONS | ACH580-01 BXR UL TYPE 1 & 12, R1/R2

Step Instruction Diagram

18 Power and reprogram the drive.

19 Test and verify drive operation and motor direction.

20 Back-up and save parameters to the keypad prior to putting the drive

back into service.

Otros manuales para ACH580-01 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accionamiento de CC de ABB

ABB

ABB ACH580-01 Series Manual de instalación

ABB

ABB SMISSLINE F454 Manual de servicio

ABB

ABB ACH580-31 Manual de usuario

ABB

ABB HSCXT3A-6B Manual de usuario

ABB

ABB ACS880-07 Manual de usuario

ABB

ABB ACS880-01-046A-2 Manual de usuario

ABB

ABB IRC5 Compact Instrucciones de uso

ABB

ABB ACS580-07 Manual de usuario

ABB

ABB ACS880 PCP Manual de uso y cuidado

ABB

ABB ACH580 Series Guía de configuración

ABB

ABB ACS380 Series Manual de instalación

ABB

ABB ACS580-01 drives Manual del propietario

ABB

ABB ACH550-UH-011A-6 Manual de usuario

ABB

ABB ACH550 series Manual de usuario

ABB

ABB ACQ580-34 Manual de usuario

ABB

ABB ACx580-01 Series Manual de usuario

ABB

ABB ACS310 Manual de usuario

ABB

ABB ACS250 Manual del propietario

ABB

ABB ACS 580-OP Manual de usuario

ABB

ABB ACS880-01 Series Guía del usuario

ABB

ABB ACS560 Manual de instalación

ABB

ABB ACS560 Manual de uso y cuidado

ABB

ABB ACQ580-04 Manual de usuario

ABB

ABB ACS580-01 drives Manual de instalación

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

Danfoss

Danfoss VLT 2800 Series Hoja de especificaciones

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario

Beckhoff

Beckhoff AX8911 Manual del operador

Minarik

Minarik MM300 Series Manual de usuario