ABB Relion 615 series Hoja de datos
Relion® 615 series
Motor Protection and Control
REM615 ANSI
DNP3 Point List Manual
Document ID: 1MAC254287-MB
Issued: 01/20/2010
Revision: A
Product version: 2.0
© Copyright 2010 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third party,
nor used for any unauthorized purpose.
The software or hardware described in this document is furnished under a license and
may be used, copied, or disclosed only in accordance with the terms of such license.
Trademarks
ABB and Relion are registered trademarks of ABB Group. All other brand or product
names mentioned in this document may be trademarks or registered trademarks of their
respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
ABB Inc.
Distribution Automation
4300 Coral Ridge Drive
Coral Springs, FL 33065, USA
Toll-free: 1 (800) 523-2620
Phone: +1 954-752-6700
Fax: +1 954 345-5329
http://www.abb.com/substationautomation
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or
product description and are not to be deemed as a statement of guaranteed properties.
All persons responsible for applying the equipment addressed in this manual must
satisfy themselves that each intended application is suitable and acceptable, including
that any applicable safety or other operational requirements are complied with. In
particular, any risks in applications where a system failure and/or product failure would
create a risk for harm to property or persons (including but not limited to personal
injuries or death) shall be the sole responsibility of the person or entity applying the
equipment, and those so responsible are hereby requested to ensure that all measures
are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested to
notify the manufacturer. Other than under explicit contractual commitments, in no
event shall ABB be responsible or liable for any loss or damage resulting from the use
of this manual or the application of the equipment.
Conformity
This product complies with the directive of the Council of the European Communities
on the approximation of the laws of the Member States relating to electromagnetic
compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for
use within specified voltage limits (Low-voltage directive 2006/95/EC). This
conformity is the result of tests conducted by ABB in accordance with the product
standards EN 50263 and EN 60255-26 for the EMC directive, and with the product
standards EN 60255-6 and EN 60255-27 for the low voltage directive. The IED is
designed in accordance with the international standards of the IEC 60255 series and
ANSI C37.90. The DNP protocol implementation in the IED conforms to "DNP3
Intelligent Electronic Device (IED) Certification Procedure Subset Level 2", available
at www.dnp.org .
Table of contents
Section 1 Introduction............................................................................3
This manual..............................................................................................3
Intended audience....................................................................................3
Product documentation.............................................................................4
Product documentation set..................................................................4
Document revision history...................................................................5
Related documentation........................................................................6
Symbols and conventions.........................................................................6
Safety indication symbols....................................................................6
Manual conventions.............................................................................6
Functions, codes and symbols............................................................7
Section 2 DNP3 data mappings............................................................9
Overview...................................................................................................9
Point list for REM615 Ver. 2.0 ANSI.........................................................9
Section 3 DNP3 protocol implementation............................................21
DNP3 device profile................................................................................21
DNP3 implementation table....................................................................23
Section 4 Glossary..............................................................................27
Table of contents
REM615 ANSI 1
Point List Manual
2
Section 1 Introduction
1.1 This manual
The point list manual describes the outlook and properties of the data points specific to
the IED. The manual should be used in conjunction with the corresponding
communication protocol manual.
1.2 Intended audience
This manual addresses the communication system engineer or system integrator
responsible for pre-engineering and engineering for communication setup in a
substation from an IED perspective.
The system engineer or system integrator must have a basic knowledge of
communication in protection and control systems and thorough knowledge of the
specific communication protocol.
1MAC254287-MB A Section 1
Introduction
REM615 ANSI 3
Point List Manual
1.3 Product documentation
1.3.1 Product documentation set
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Application manual
Operation manual
Installation manual
Service manual
Engineering manual
Commissioning manual
Communication protocol
manual
Technical manual
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Application manualApplication manual
Operation manualOperation manual
Installation manualInstallation manual
Service manualService manual
Engineering manualEngineering manual
Commissioning manualCommissioning manual
Communication protocol
manual
Communication protocol
manual
Technical manualTechnical manual
en07000220.vsd
IEC07000220 V1 EN
Figure 1: The intended use of manuals in different lifecycles
The engineering manual contains instructions on how to engineer the IEDs using the
different tools in PCM600. The manual provides instructions on how to set up a
PCM600 project and insert IEDs to the project structure. The manual also recommends
a sequence for engineering of protection and control functions, LHMI functions as well
as communication engineering for IEC 61850 and DNP3.
The installation manual contains instructions on how to install the IED. The manual
provides procedures for mechanical and electrical installation. The chapters are
organized in chronological order in which the IED should be installed.
The commissioning manual contains instructions on how to commission the IED. The
manual can also be used by system engineers and maintenance personnel for assistance
Section 1 1MAC254287-MB A
Introduction
4REM615 ANSI
Point List Manual
Otros manuales para Relion 615 series
41
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de control de ABB
ABB
ABB Ability 800xA Series Manual de instrucciones
ABB
ABB MOD 30ML Manual de usuario
ABB
ABB Relion 620 Series Manual de usuario
ABB
ABB Advant AC500 Manual de usuario
ABB
ABB MicroSCADA Pro SYS 600C 2.93 Manual de usuario
ABB
ABB REC670 2.1 IEC Manual de usuario
ABB
ABB MNS iS Hoja de especificaciones
ABB
ABB Relion REC670 Manual de usuario
ABB
ABB Ability 800xA Series Manual de usuario
ABB
ABB LVS Digital FC610 Manual de usuario
ABB
ABB Relion REC670 Manual de usuario
ABB
ABB Relion 670 series Guía del usuario
ABB
ABB Relion 615 series Manual de usuario
ABB
ABB 620 Series ANSI Manual de usuario
ABB
ABB ACSM1 Series Manual de usuario
ABB
ABB C581 Manual de usuario
ABB
ABB Ability 800xA Series Manual de instrucciones
ABB
ABB AC500 Series Instrucciones de instalación
ABB
ABB SafeGear MCC Manual de usuario
ABB
ABB ACS800-02 Manual de usuario
