© 2017 ABB SACE Emax 2 | I1SDH000999R0002 - ECN000058721 - Rev. B
Emax E1.2 circuit-breakers.......................................................... 4
1 - Contents .........................................................................4
Organization of this handbook .............................................. 4
Intended readership.............................................................. 4
Instructions........................................................................... 4
Integrated informations......................................................... 4
Warnings............................................................................... 5
Standards ............................................................................. 6
2 - Transport and checking on receipt..................................7
Introduction .......................................................................... 7
Weight of the circuit-breakers with packaging ...................... 7
Transport of the packaged circuit-breaker ........................... 7
Identification of packaging.................................................... 8
Packaging checks................................................................. 8
Damage and Discrepancy Report ......................................... 8
Storage method .................................................................... 9
3 - Unpacking and handling ...............................................10
Opening the packaging....................................................... 10
Weight of circuit-breakers without packaging ..................... 11
Disposal of packing materials ............................................. 11
4 - Description ...................................................................12
Description of circuit-breaker.............................................. 12
Description of the circuit-breaker front panel...................... 13
Description of electrical data plate IEC ............................... 13
Description of electrical data plate UL ................................ 14
Manual operations for opening and closing the circuit-
breaker ............................................................................... 15
Mechanical status indicators .............................................. 17
Circuit breaker racking-in/racking-out operations ............... 18
Mechanical position indicators ........................................... 20
5 - Environmental conditions..............................................21
Installation environment...................................................... 21
Temperatures of the installation environment...................... 21
Particular weather conditions.............................................. 21
Dusty environments ............................................................ 21
Vibration ............................................................................. 21
Altitude ............................................................................... 22
Electromagnetic compatibility............................................. 22
Storage Environment .......................................................... 22
6 - Installation ....................................................................23
Warnings and precautions before the installation................ 23
Mounting of the fixed circuit-breaker .................................. 23
Mounting anti-insertion locks.............................................. 23
Mounting the fixed part of the withdrawable circuit-breaker 24
Types of terminal................................................................. 24
Change of position of the vertical/horizontal terminals ....... 27
Connection to the power circuit.......................................... 28
Dimensions ......................................................................... 29
Positioning anchor plates ................................................... 30
Introduction to Ekip protection trip units.................................. 31
1 - Presentation..................................................................31
Families and functionality ................................................... 31
Protections ......................................................................... 32
Measurements .................................................................... 32
Integrated functions: Self-diagnosis, Test and Power
Controller............................................................................ 33
Accessorizing modules ....................................................... 33
Ekip Dip protection trip unit....................................................... 34
1 - Operator interface.........................................................34
Introduction ........................................................................ 34
Components of the interface............................................... 34
LEDs................................................................................... 35
Protections: thresholds ....................................................... 35
Protections: times............................................................... 35
Settings .............................................................................. 35
iTest pushbutton ................................................................. 36
Test connector .................................................................... 36
2 - Protections ...................................................................37
L Protection ........................................................................ 37
S Protection........................................................................ 38
I Protection ......................................................................... 39
G Protection ....................................................................... 40
Neutral and frequency......................................................... 41
Additional protections......................................................... 42
Summary table of protections............................................. 43
3 - Measurements ..............................................................44
Introduction Measurements ................................................ 44
Instantaneous currents ....................................................... 44
Maximum and minimum currents........................................ 44
Trips.................................................................................... 44
Contact Wear...................................................................... 44
Number of operations ......................................................... 44
4 - Test...............................................................................45
Presentation........................................................................ 45
LED test.............................................................................. 45
Battery test ......................................................................... 45
Protection test .................................................................... 45
Opening test ....................................................................... 45
5 - List of alarms and signals .............................................46
LED view............................................................................. 46
Summary table of LED signals ............................................ 47
6 - Ekip Dip: additional functions .......................................49
Maintenance ....................................................................... 49
Local Bus............................................................................ 49
Date and time ..................................................................... 49
Programmable States ......................................................... 49
Circuit-breaker label and user Data..................................... 49
Info Page ............................................................................ 49
Date of installation .............................................................. 49
Load Profile Timers............................................................. 49
Energy Store Time .............................................................. 50
Led Alive............................................................................. 50
Open/Close Remote Direct Command ................................ 50
Modules network settings retention .................................... 50
Wink ................................................................................... 50
Glitch .................................................................................. 50
7 - Operating features ........................................................51
Primary operating currents.................................................. 51
Auxiliary power supply........................................................ 51
8 - Default parameters .......................................................52
Ekip Dip default parameters................................................ 52
Accessories ................................................................................ 53
1 - Preliminary considerations............................................53
Introduction ........................................................................ 53
Accessory combination tables ............................................ 53
Circuit-breaker dismantling operations ............................... 55
2 - Circuit diagrams............................................................56
General wiring diagrams ..................................................... 56
Circuit-breaker terminal box ............................................... 57
Electronic accessories............................................................... 62
3 - Ekip Supply modules ....................................................62
Description ......................................................................... 62
Compatibility....................................................................... 62
Electrical characteristics..................................................... 62
Connections ....................................................................... 63
Signallings .......................................................................... 63
4 - Ekip Link module ..........................................................64
