ABB FCNA-01 Manual de instalación
Options for ABB drives, converters and inverters
Quick installation and start-up guide
FCNA-01 ControlNet adapter module
Safety instructions
WARNING! Obey the safety instructions. If you ignore them, injury or death, or damage to the
equipment can occur. See the user’s manual.
Mechanical installation
Electrical installation
Layout of the module
1. Pull out the lock.
2. Install the module carefully to an option
module slot of the drive. See the drive
hardware manual.
3. Push in the lock.
4. Tighten the screw to torque 0.8 N·m using
a Torx TX10 screwdriver.
WARNING! Do not use excessive force,
or leave the screw too loose. Over-
tightening can damage the screw or
module. A loose screw decreases the EMC
performance, and can even cause an operation
failure.
13
4
No. Description
1Lock
2 Mounting and grounding screw
3 Bus connector line [A]
4 Network access port (NAP) for a temporary
connection of configuration tools
5 Bus connector line [B]
6 Diagnostic LEDs
7 Node ID address selection switches
6
3
2
5
1
4
7
Connection procedure
1. Connect the bus cable to the BNC connectors [A] and/or [B] on the module. Use both connectors in
redundant operation, otherwise use either connector [A] or [B].
2. Terminate the ControlNet bus line with a 75-ohm resistor.
Start-up
When the module is connected to the drive, the drive control program sets the applicable parameters.
See the appropriate drive manual.
Basic parameter settings
To take the settings into use, validate and refresh the parameters with parameter 51.27 FBA par refresh.
Set the node address of the device with the rotary switches on the module.
Further information
Index Name Value
20.01 Ext1 commands Fieldbus A
22.11 Speed ref1 source FBA A ref 1
28.11 Frequency ref1 source FBA A ref 1
50.01 FBA A enable Enable (or select the option slot in which the module is installed)
50.02 FBA A comm loss func Fault
51.02 Profile The ODVA AC/DC drive profile is the default value.
See the latest version of FCNA-01 ControlNet adapter
module user's manual (3AUA0000141650 [English]) in
ABB library (www.abb.com/drives/documents).
For more information on fieldbus options and protocols
provided by ABB Drives, see the fieldbus
communications web page
(new.abb.com/drives/connectivity/fieldbus-connectivity).
3AXD50000158201 Rev A (EN) 2017-11-23
FCNA-01 manual
Fieldbus communications web page
Otros manuales de Adaptador de ABB
ABB
ABB SPA-ZC 400 Guía
ABB
ABB FieldKey NHU200 Manual de usuario
ABB
ABB Tina 2A Manual de usuario
ABB
ABB FDNA-01 Manual de usuario
ABB
ABB 8209-101-500 Manual de usuario
ABB
ABB RETA-01 Manual de usuario
ABB
ABB RETA-01 Manual de usuario
ABB
ABB 2769522-C Manual del producto
ABB
ABB SPA-ZC 402 Guía
ABB
ABB JOKAB SAFETY Tina 6A Manual de usuario
ABB
ABB FEPL-02 Ethernet POWERLINK Manual de usuario
ABB
ABB SPA-ZC 402 Guía
ABB
ABB 520ADD02 Instrucciones de uso
ABB
ABB RS485 Modbus adapter Manual de instalación
ABB
ABB Tina 3A/Aps Manual de usuario
ABB
ABB FBIP-21 BACnet/IP Manual de instalación
ABB
ABB CEM 05100 Manual de usuario
ABB
ABB Tina 10B Manual de usuario
ABB
ABB CCA-01 Manual de usuario
ABB
ABB RECA-01 Manual de usuario
