A-iPower AP170F Manual de usuario
Operating Manual
CUSTOMER SERVICE
SERVICE CLIENTELE
SERVICIO AL CLIENTE
1-855-888-3598
SAVE THIS MANUAL FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTIONS ARE INCLUDED IN THIS MANUAL
A-iPOWER Corp.
1477 E. Cedar St. #B,
Ontario, CA 91761
U.S.A.
www.a-ipower.com
Actual product may differ
from image shown.
2
LIMITED WARRANTY
YEAR
7. STORAGE OF ENGINE………………………………………………
8. TROUBLE SHOOTING………………………………………………
9. ELECTRIC DIAGRAM………………………………………………
10. EXPLODED PARTS DIAGRAM AND PARTS LIST……………
11. WARRANTY ……………………..………........................................
6. INSPECTION AND MAINTENANCE………………………………
4. PRE-OPERATION INSPECTION…………………………………..
5. STARTINGAND STOPPING THE ENGINE………………………
1. SAFETY TIPS…………………………………………………………
2. SPECIFICATIONS AND PARTS DESCRIPTION…………………
3. FUELAND ENGINE OIL……………………………………………
CONTENTS
1
1
This engine is designed to operate in temperature between -10℃to +40℃.
Thank you for purchasing this general purpose engine.
This Operation Manual tells you how to operate and service your gasoline engine. Please read
it before using the engine to ensure proper handling and operating. Follow the instructions
carefully to keep your engine in the best running condition.
This Operation Manual deals with the main operating points of the engine. If you have any
questions concerning this manual or any suggestions, please call 1.855.888.3598 or email
Warning
This general purpose gasoline engine is designed to provide safe and dependable service
provided that it is operated according to the Operation Manual.
Read and understand the Operation Manual before operating the engine as failure to do so
could result in personal injury or equipment damage
1. SAFETY TIPS
WARNING:
These items are very important for safety. Please be sure to obey them.
•Do not allow people who do not understand this OPERATION MANUAL to operate the engine.
•Do not run the engine indoors or where ventilation is poor.
•Keep explosives and flammables at least 1m (3ft) away from the engine.
•Do not smoke when adding fuel.
•Do not run the engine when gasoline has overflowed, clean the overflowed fuel and fuel spillage.
•Do not remove the fuel tank cap or add fuel while the engine is running or hot. (Add fuel after the engine has
cooled by waiting 2 or more minutes after engine has stopped.)
•Do not remove or run the engine without-muffler or air cleaner.
•Do not touch the muffler, muffler cover or engine body while the engine is running or hot.
2. SPECIFICATIONS AND PARTS DESCRIPTION
2-1. Specifications
2-2. Parts Description
2
2
Model AP168FB AP170F AP188F AP192FBD
Engine Type Single Cylinder,
4.Stroke,Forced Coolling
OHV
Single Cylinder,
4.Stroke,Forced Coolling
OHV
Single Cylinder,
4.Stroke,Forced Coolling
OHV
Single Cylinder,
4.Stroke,Forced Coolling
OHV
Bore And Stroke(mm×mm
）
68×54 70×56 88×64 92×69
Displacement 196cc 208cc 390cc 459cc
Compression 8.5:1 8.5:1 8.5:1 8.5:1
Starting Method Recoil Start Recoil Start Recoil Start Electric Start
Ignition Method Transistorized Ignition Transistorized Ignition Transistorized Ignition Transistorized Ignition
Lubrication Method Pressure And Splash Pressure And Splash Pressure And Splash Pressure And Splash
Rated Output(Kw-r/min）3.8/3600 4.0/3600 7.6/3600 9.2/3600
Max Torque（N.m-r/min）10.7/2500 11.7/2500 22/2500 29/2800
Min.fuel
Consumption(g/Kw.h
）≤375 ≤375 ≤375 ≤375
shaft Rotation Anticlockwise Anticlockwise Anticlockwise Anticlockwise
Air Cleaner Type Filter Paper and
Foamed Plastic
Filter Paper and
Foamed Plastic
Filter Paper and
Foamed Plastic
Filter Paper and
Foamed Plastic
Dimension
（mm×mm×mm) 376×312×335 376×320×340 455×405×445 455×405×445
Net Weight
（
Kg
）
16 17 33 33
3. FUEL AND ENGINE OIL
3-1. Fuel
·
Use clean, fresh, unleaded gasoline.
·
Do not mix oil into the gasoline.
·
Do not overfill the gasoline when filling the fuel tank.
WARNING:
·
Flame and heat can cause gasoline to explode. Be careful of flame and heat when handling gasoline.
3-2. Engine oil
·
Use the engine oil as described in the table below.
Note: Recommended engine oil: SAE 10W-30
·
Do not add commercial additives to the oil.
·
Do not mix gasoline into the oil.
WARNING:
Engine is shipped without oil. Before starting, be sure to conduct an oil inspection
Oil gauge
by following the instructions:
①Place the engine on a level surface when adding oil or inspecting;
Check the oil level without the oil gauge screwed in;
Fill the oil up to level of oil gauge;
Before starting the engine, tightly screw in oil gauge.
3
3
4. PRE-OPERATION INSPECTION
4-1. Fuel Inspection
·Is there gasoline in the tank?
·Is old gasoline being used?
·Is the fuel tank cap closed correctly?
WARNING:
Be sufficiently careful of heat and flame when handling the fuel. Not doing so could cause fire or explosion.
4-2. Air-cleaner Inspection
·Is the air-cleaner element dirty?
·When the air-cleaner element is dirty, clean it.
4-3. Engine Oil Inspection
·Is the engine filled with the recommended engine oil, and is the oil dirty?
·If there is not enough oil, if it is dirty, or it has been used longer than the specified time,
add or change the engine oil.
4-4. Inspect the Tightness of all Fasteners or Screws
·Are all the screws tight?
·Be sure to check the screw used to fasten the muffler.
(Do this when the muffler is cold)
4-5. Fuel and Oil Leaks Inspection
·Are there any fuel or oil leaks? If any are found repair them.
4
4
5. STARTING AND STOPPING THE ENGINE
5-1. Starting the Engine
WARNING:
Before starting the engine, carefully read and understand the “SAFETY TIPS” and “PRE-OPERATION
INSPECTION” section of this OPERATION MANUAL.
①OPENthefuelvalve. ②Turn the engine switch to “ON” position.
Fuel valve
③Completely CLOSE the choke lever. ④Move the throttle lever toward.
Choke lever
OFF Throttle lever
⑤ Start the engine as follow:
a. Recoil start:
• Hold the starter handle and pull it slightly
Until the compression position is reached,
And then pull it swiftly from this position;
• Slowly return the starter handle to its original
position after the engine starts.
Starter handle
b. Electric starter
Turn the engine switch to “START” until the engine starts.
5
5
⑥
After the engine starts, gradually turn the choke lever to the full “OPEN”
position, and set the throttle lever in the Max. position. Before loading,
warm up the engine for about 3minutes.
5-2. Stopping the Engine
①Move the throttle lever to “CLOSE” position;
Fuel valve
Throttle lever
②Turn the engine switch to “OFF” position;
③Close the fuel valve.
NOTE:
•In emergency, turn the engine switch to “OFF” to stop the engine.
WARNING:
•Never stop the engine at high speed or under heavy load, otherwise, damage can result.
6
6
6. INSPECTION AND MAINTENANCE
6-1.Daily and Regular Inspection
WARNING:
Daily and regular inspections are important to assure safe, proper and long-term operation of the engine.
Refer to the regular inspection table when conducting inspections and maintenance.
Regular Inspection Table:
Every operation Every 25 hours Every 25 hours Every 100 hours
Inspection and tightening of bolts and nuts ○
Engine oil level check and add ○
Change engine oil ●
onlythefirsttime
○
Check for fuel and oil leaks ○
Check and clean the air cleaner ○
Check and clean spark plug ○
Check and clean fuel strainer ○
Remove carbon in combustion chamber ◎
Check and adjust valve clearance ◎
Replace the fuel lines 2 years (or when necessary)
Noted: Item marked with a ◎require advanced skill and tools, so they should be done by a qualified service person.
6-2. Parts Maintenance
①
Cleaning the air cleaner
Time
Item
•
Loosen the wing-
nut and remove the
air cleaner cap;
•
Loosen the wing-nut
and washer, remove
the element;
•
Separate the primary and
secondary element;
•
Tap the element or use
compressed air to blow
from
•
Reassemble the air cleaner;
Wet down
Kerosene
Wring
Squeeze
7
7
②Cleaning the spark plug
•
Remove the spark plug;
•
Polish the electrode with emery paper or wire brush;
•
Adjust the electrode gap.
③Cleaning the fuel filter
•
Remove the filter from fuel tank;
•
Clean it in solvent
•
Wipe off;
•
Replace the filter into fuel tank.
④Cleaning the deposit cup of the fuel valve
•
Remove the cup from fuel valve;
•
Clean the cup;
•
Replace the cup use a new O-ring.
8
8
Tabla de contenidos
Idiomas:
