A/DA PLATINUM II Manual de usuario
OWNER’S MANUAL
PLATINUM II
ZONE CONTROL SYSTEM
PLATINUM II
TABLE OF CONTENTS
1.QuickStartGuide 2
2.ProductDescription 3
3.Precautions 3
4.SystemOperation 4
5.ChangingZoneSettings 5
6.ChangingZoneNames 8
7.SavingZoneSettingsasFavourites 10
8.Favourites 13
9.ChangingFavouriteNames 14
10.BoostFunction 15
11.ReliefZones 16
12.EnergySavingMode 17
13.Faults 17
14.TurningSystemOff 21
15.Warranty 22
16.Troubleshooting 23
1
PLATINUM II
TABLE OF CONTENTS
1.QuickStartGuide 2
2.ProductDescription 3
3.Precautions 3
4.SystemOperation 4
5.ChangingZoneSettings 5
6.ChangingZoneNames 8
7.SavingZoneSettingsasFavourites 10
8.Favourites 13
9.ChangingFavouriteNames 14
10.BoostFunction 15
11.ReliefZones 16
12.EnergySavingMode 17
13.Faults 17
14.TurningSystemOff 21
15.Warranty 22
16.Troubleshooting 23
1
PLATINUM II
QUICK START GUIDE
OWNER’S MANUAL
2
3
1. Quick Start Guide
1. OFF
2. FAVOURITES – use to select Favourite setting
3. SAVE – save settings to a particular Favourite
4. UP/DOWN – use to scroll Zones up or down
5. ZONE – select to modify Zone settings, indicates current Zone setting. Hold
for 2 seconds to change Zone Name
6. FAVOURITE NAME – shows current Favourite setting. Hold for 2 seconds to
rename Favourite
7. SYSTEM SET UP – access System Setup functions
8. LEFT/RIGHT – use to adjust Zone setting of currently highlighted Zone
9. BOOST – fully opens selected Zones temporarily to condition the airspace as
quickly as possible
10. AUTO/MANUAL – select Auto or Manual function for selected Zone
7
8
6
5
42 1
PLATINUM II
2. Product Description
The Platinum II Zone Control System controls the airflow to each room or Zone
within the building. The ultimate temperature of the building is controlled by
the air conditioner thermostat, whilst the Platinum II system will maximise the
effectiveness of the air distribution. The system controls the Zone Dampers to
accurately manage the airflow to each Zone, maximizing occupant comfort.
Zones can be closed off completely if not in use. Using optional wireless Zone
Sensors that can monitor a rooms temperature, the system can be programmed
to adjust automatically. Used properly, the system can reduce energy
consumption – it is designed to optimize the use of heating and cooling within
the building.
The system can control up to 8 Zones with a single Control Box, or 16 Zones by
linking two Control Boxes. Both configurations can be managed by either one or
two Touch Screens.
Each Zone can be named for ease of recognition.
The Platinum II system can be programmed with up to 8 different Favourite
settings. A Favourite is the name given to a programmed set of Zones. The name
can be descriptive to communicate the purpose of the programmed settings, eg.
Casual Living, Bedrooms Off, Night Settings, etc.
3. Precautions
This appliance is not to be used by persons, including children with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction.
3
PRODUCT DESCRIPTION
9
10
Auto System only
QUICK START GUIDE
OWNER’S MANUAL
2
3
1. Quick Start Guide
1. OFF
2. FAVOURITES – use to select Favourite setting
3. SAVE – save settings to a particular Favourite
4. UP/DOWN – use to scroll Zones up or down
5. ZONE – select to modify Zone settings, indicates current Zone setting. Hold
for 2 seconds to change Zone Name
6. FAVOURITE NAME – shows current Favourite setting. Hold for 2 seconds to
rename Favourite
7. SYSTEM SET UP – access System Setup functions
8. LEFT/RIGHT – use to adjust Zone setting of currently highlighted Zone
9. BOOST – fully opens selected Zones temporarily to condition the airspace as
quickly as possible
10. AUTO/MANUAL – select Auto or Manual function for selected Zone
7
8
6
5
42 1
PLATINUM II
2. Product Description
The Platinum II Zone Control System controls the airflow to each room or Zone
within the building. The ultimate temperature of the building is controlled by
the air conditioner thermostat, whilst the Platinum II system will maximise the
effectiveness of the air distribution. The system controls the Zone Dampers to
accurately manage the airflow to each Zone, maximizing occupant comfort.
Zones can be closed off completely if not in use. Using optional wireless Zone
Sensors that can monitor a rooms temperature, the system can be programmed
to adjust automatically. Used properly, the system can reduce energy
consumption – it is designed to optimize the use of heating and cooling within
the building.
The system can control up to 8 Zones with a single Control Box, or 16 Zones by
linking two Control Boxes. Both configurations can be managed by either one or
two Touch Screens.
Each Zone can be named for ease of recognition.
The Platinum II system can be programmed with up to 8 different Favourite
settings. A Favourite is the name given to a programmed set of Zones. The name
can be descriptive to communicate the purpose of the programmed settings, eg.
Casual Living, Bedrooms Off, Night Settings, etc.
3. Precautions
This appliance is not to be used by persons, including children with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction.
3
PRODUCT DESCRIPTION
9
10
Auto System only
4. System Operation
If the installer has left the
system in an off state, press
'ON' to initialize the system.
The system will check the
installed components during
the initialization process. (This
will also occur following a
power interruption.)
Once the initialization process
is complete, the Base Screen is
displayed. If the installer has
programmed Zone names and
Favourites, the Base Screen
may look like this:
USER GUIDE
OWNER’S MANUAL
45
If it is an Auto system, the Base
Screen may look like this:
5. Changing Zone Settings
Select Zone.
Use arrows to change
percentage to desired comfort
level or ‘Off’.
If the Zone being changed has
been set as a Relief Zone and
becomes active, the Relief
function will operate in
preference to the user setting.
Refer to Relief Zone section for
more information.
USER GUIDE
PLATINUM II
4. System Operation
If the installer has left the
system in an off state, press
'ON' to initialize the system.
The system will check the
installed components during
the initialization process. (This
will also occur following a
power interruption.)
Once the initialization process
is complete, the Base Screen is
displayed. If the installer has
programmed Zone names and
Favourites, the Base Screen
may look like this:
USER GUIDE
OWNER’S MANUAL
45
If it is an Auto system, the Base
Screen may look like this:
5. Changing Zone Settings
Select Zone.
Use arrows to change
percentage to desired comfort
level or ‘Off’.
If the Zone being changed has
been set as a Relief Zone and
becomes active, the Relief
function will operate in
preference to the user setting.
Refer to Relief Zone section for
more information.
USER GUIDE
PLATINUM II
USER GUIDE
OWNER’S MANUAL
67
USER GUIDE
PLATINUM II
For an Auto system, the default
setting for each Zone is Auto
mode.
An offset temperature can be
set in Auto mode to increase or
decrease airflow to the Zone,
raising or lowering the
temperature relative to Zones
with no offset.
The system can automatically
detect whether the air
conditioner is heating or
cooling. The colour of the
offset bar will indicate whether
the system is in heating or
cooling mode.
Alternatively an individual
Zone can be set to Manual
mode and operated as
previously described.
Manual mode is ideal when
one Zone requires a minimal
amount of air or is not being
used and can be turned off.
USER GUIDE
OWNER’S MANUAL
67
USER GUIDE
PLATINUM II
For an Auto system, the default
setting for each Zone is Auto
mode.
An offset temperature can be
set in Auto mode to increase or
decrease airflow to the Zone,
raising or lowering the
temperature relative to Zones
with no offset.
The system can automatically
detect whether the air
conditioner is heating or
cooling. The colour of the
offset bar will indicate whether
the system is in heating or
cooling mode.
Alternatively an individual
Zone can be set to Manual
mode and operated as
previously described.
Manual mode is ideal when
one Zone requires a minimal
amount of air or is not being
used and can be turned off.
USER GUIDE
OWNER’S MANUAL
USER GUIDE
PLATINUM II
89
6. Changing Zone Names
Hold for 1 second. Alternatively for a custom
name:
Otros manuales para PLATINUM II
2
Tabla de contenidos
Otros manuales de Sistema de control de A/DA
