4CR ECO IR 1 Manual de usuario
car refinish
6.9752.0001
ECO IR 1
Infrared dryer
Content
1. Precaution 1
2. Technical specifications 2
3. Installation 3
4. Operation 4
5. Trouble shooting 5
6. Light tube exchange 6
7. Circuit diagran 7
1. Precaution
1. Read this manual carefully before installing or using the device.
2.
Before first use, check / unscrew connections of the fluorescent tubes. If
the screw connection is too strong, the arc tube will break due to
temperature induced expansion.
3.
Attention! Device becomes hot, risk of injury and fire!
4.
This device is intended for paint drying applications. Set the correct
temperature and keep the minimum safe distance from the heat source during
operation. Improper use can lead to surface damage.
5. Installation and maintenance must be performed by a qualified installer
or service company.
6.
The system is designed for easy installation, low operating costs and
minimal maintenance. The warranty does not cover damage to the
fluorescent tube caused by incorrect handling or incorrect operation.
7.
The warranty does not cover damage caused by improper use.
8.
Disconnect the power source when the unit is not going to be used for a
long time.
9. The tubes should not be perpendicular to the ground when the device is
turned on. Otherwise, the life of the arc tube is shortened.
10.
Before use, make sure the cartridge connector is firmly connected.
1
2. Technical specifications
Model
ECO IRE1
Input voltage
230V 50/60Hz Single phase
Total power
1100W
Curing area
800x500mm
Temperature
40°C - 75°C adjustable
Timer
0 Min – 60 Min adjustable
Light intensity
100%
2
Attention!
Check if the
plugs are
connected
1. Power switch
2. Control
3. Cassette
4. Lamp bracket
5. Column
6. Substructur
7. Column base
8. Roll / brakes
3. Installation
1. Installation of the substructure:
a. Remove the substructure from the packaging.
b. Place the substructure on the ground.
c. Attach the four wheels to the base and tighten the screws.
d. Make sure the rollers with brakes are mounted on the back of the substructure.
2. Installation of the column:
a. Remove the column from the packaging.
b. Place the column vertically on the base and screw it together.
Installation of the lamp bracket:
a. Remove the lamp bracket from the packaging.
b. Connect the lamp bracket to the column and screw it tight.
c. Connect the control cables and adjust the angle of the lamp bracket.
Further information can be found on page 2.
3
4. Operation
1. Connect the electricity. The supply cable must be at least 4mm² at 230V.
Make sure the supply
voltage and frequency are as specified correspond to the type
plate of the device.
2. Set the distance between the device and the workpiece. Usually a distance of 30 – 60
cm is to be kept.
3. Switch on the device with the ON / OFF switch. Set time and temperature according
to the manufacturer’s specifications of the applied materials to achieve the desired
result.
4. After the timer has elapsed, switch OFF the device with the ON / OFF switch.
5. After use, disconnect the device from the power supply and store it in a safe place to
Prevent improper handling and damage to the device and the fluorescent tube.
Watch out! Device heats up during use. Injury and fire hazard!
Switch off the appliance after use. Store the device in a safe place to avoid
damage.
ON/OFF TIMER
4
5. Trouble shooting
Error
Reason
Solution
Light tube doesn‘ work
1. Light tube defective
2. Not connected
1. Check the light tube / if
necessary exchange*
2. Check connectionss
Device can not be
switched on/off
1. Malfunction main
switch
2. Malfunction timer
1. Check main switch,
replace if necessary*
2. Check timer, if necessary
exchange*
*Exchange may only be carried out by qualified and trained service personnel.
5
6. Light tubes exchange
1. Remove cassette for tube replacement
2. Remove protective grille
3. Remove both holder plates from the sides of the
cassette
4. Remove the fixed plates from both ends of the
cassette
5. Disconnect cable connections and screws.
Subsequently the arc tube can be exchanged
6. Follow the reverse order of assembling the
cassette
6
7. Circuit diagram
7
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Secadora de 4CR
Manuales populares de Secadora de otras marcas
Indesit
Indesit IDV 75 Manual de usuario
Infiniton
Infiniton SD-DG85C Manual de usuario
BOMANN
BOMANN WT 5019 Manual de usuario
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Manual de usuario
Asko
Asko T793C Manual de usuario
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario