3SAE TECHNOLOGIES AS II Manual de usuario

AS II

User’s Guide

 
ASII Users Guide | 1/24/2019 
Safety Information & Precautions ____________________________________________________ 5 
Transportation & Storage ___________________________________________________________ 7 
Introduction to the AS II_____________________________________________________________ 8 
Operational Features_____________________________________________________________ 8 
Safety Features__________________________________________________________________ 9 
Unboxing the AS II________________________________________________________________ 10 
The AS II at a Glance____________________________________________________________ 11 
Accessories Included____________________________________________________________ 13 
Optional Accessories____________________________________________________________ 13 
Basics___________________________________________________________________________ 14 
AS II Firmware Compatibility _____________________________________________________ 14 
AS II Home Screen______________________________________________________________ 14 
AS II Buttons ___________________________________________________________________ 15 
AS II LEDs_____________________________________________________________________ 15 
Heater Lock____________________________________________________________________ 16 
Safety Shield___________________________________________________________________ 16 
Providing Air ___________________________________________________________________ 16 
Powering the AS II ______________________________________________________________ 17 
Setting Heater Temperature______________________________________________________ 17 
Zero Load Cell Response ________________________________________________________ 17 
Clamp Pressure ________________________________________________________________ 18 
General Use _____________________________________________________________________ 19 
Loading the fiber________________________________________________________________ 19 
Proof-Test Only_________________________________________________________________ 20 
Programs________________________________________________________________________ 21 
Selecting a Program_____________________________________________________________ 21 
Editing a Program_______________________________________________________________ 21 
Factory Program for SMF28______________________________________________________ 22 
Program Parameters ____________________________________________________________ 23 

ASII Users Guide | 1/24/2019

Global Parameters ______________________________________________________________ 27

Optimizing _______________________________________________________________________ 29

Introduction to Optimizing ________________________________________________________ 29

Optimizing a Fiber ______________________________________________________________ 29

Maintenance _____________________________________________________________________ 31

Replacing the Filter _____________________________________________________________ 31

Cleaning Linear Clamps _________________________________________________________ 33

Replacing Rubber Pads (optional)_________________________________________________ 35

Replacing Fuses________________________________________________________________ 37

AS II Errors ______________________________________________________________________ 38

Clamp Slipping _________________________________________________________________ 38

Fiber Too Tight _________________________________________________________________ 38

Broken Fiber ___________________________________________________________________ 38

PC Interface _____________________________________________________________________ 39

Tech Support_____________________________________________________________________ 40

ASII Users Guide | 1/24/2019

Reproduction of this manual in any form requires written permission from 3SAE Technologies,

Inc.

ASII Users Guide | 1/24/2019

Safety Information & Precautions

•The AS II must only be used for stripping optical fibers with a coating diameter up to

600um. Any attempts to use the device for any other purposes could cause injury to the

operator or impair the AS II

•For the AS II to work properly, clean air must be supplied. Unclean air can reduce the

cleanliness and strength of the stripped fiber and also can impair the operation of the AS II

•Always use eyeglasses to protect from fiber shatter

•The use of a ventilation system is recommended

•This device is plugged into a standard 115V or 230V outlet. As with any electrical device,

reasonable care is required to avoid electrical shock. If the fuses need to be replaced,

disconnect the unit from the wall outlet and used exact replacements

•Never remove any covers or parts from the unit. Only trained authorized personnel are

allowed to service the AS II

•The heated air generated by the AS II is extremely hot. It can reach temperatures up to

960°C (1760°F). It is hot enough to melt the coating on the fiber and cause severe burns to

the operator if reasonable care is not taken or instructions are not followed. The heater

nozzle and exhaust system are not accessible during normal operation. The surfaces of

these components can also cause burns

•3SAE does not recommend increasing the temperature past 960°C (1760°F); damage can

be done to the AS II and heater

•The AS II uses pneumatics and electrical actuators. Never operate the unit without the

covers, as this may cause injury to the operator

•Always dispose of fiber scraps properly

•Never use spray cleaner or compressed gas. Never pour liquid cleaner on the AS II

ASII Users Guide | 1/24/2019

•Use of the unit should be restricted to personnel that:

✓Have been appropriately trained in the handling of optical fiber and related materials.

✓Have read, understood, and will follow all usage and safety instructions in this manual.

Note: It is the responsibility of the user to use this product for its intended purpose and

according to this manual. 3SAE Technologies cannot be responsible for damages or injury

resulting from failure to follow these instructions

ASII Users Guide | 1/24/2019

Transportation & Storage

The AS II must be protected against humidity, vibrations, and shock during transportation and

storage.

Save the packaging materials and locking screw for future use and always transport the AS II

in its original packaging material and secure the heater with the locking screw to prevent

damage.

Keep the AS II clean and dry.

ASII Users Guide | 1/24/2019

Introduction to the AS II

The use of chemicals for fiber stripping is past history

The AS II is a unique product utilizing the patented “Burst Technology” for fast and chemical

free window stripping of optical fibers with coatings up to 600um diameter.

The AS II was developed to meet the industry’s needs for variable window strip lengths with

high strength and ultra cleanliness.

The Burst Technology instantly vaporizes the fiber coating; the result is a stripped fiber,

perfectly clean, with high strengths.

The AS II is equipped with a built in tensile tester, which can pull up to 20N.

To ensure high quality, repeatability, and a high production yield, all critical processes and

parameters such as stripping distance, burst temperature, burst speed, and strength test are

controlled by built in microprocessors.

The fibers are easily placed in the correct position by guided linear clamps and a “One Touch”

go button that starts the stripping process automatically.

Operational Features

•Chemical free stripping

•Easy low maintenance bench top design

•Fast cycle time

•High 1st pass yield

•Accommodates fibers with coatings up to 600um

•Accommodates ribbon fibers from 4, 8, and 12 (with optional nozzle)

•Software adjustable parameters

•RS232 interface

ASII Users Guide | 1/24/2019

•Automated linear fiber clamps

•Variable strip length from 3mm to 150mm

•Built in high force linear tensile test

Safety Features

•All stripping processes are done inside the unit. Exposure to moving parts, hot gases, and

surfaces by user is extremely limited

•Safety shield to protect the operator from broken fiber shatter

•Exhaust systems with air filter for organic vapors

•Built in battery driven cooling fan allows the heater temperature to cool down slowly even if

the unit is disconnected from the wall outlet

•Fused for electrical protection

ASII Users Guide | 1/24/2019

Unboxing the AS II

1 Begin by opening the box.

2 Remove the AS II unit.

3 Remove all of the included accessories.

4 Compare the contents of the package with the Accessories Included list and the packing

slip to verify that everything has been received.

Tabla de contenidos

Manuales populares de Equipos industriales de otras marcas

ABB

ABB Unifix AD Manual

Mark 7

Mark 7 Evolution Manual de usuario

Husky

Husky HyPET Manual de usuario

bora

bora PM-1800 Manual de usuario

Grizzly

Grizzly T32428 Manual de usuario

Siemens

Siemens 8MF1 Series Manual de usuario

ABB

ABB HT610965 Manual de usuario

ABB

ABB SafeLink Manual de usuario

Phoenix

Phoenix PHX-150 Manual de usuario

ABB

ABB A165-L32 Manual de usuario

ABB

ABB HT842936 Manual de usuario

Rioned

Rioned UrbanJet Manual de usuario

Hermetica

Hermetica 10 Series Manual de usuario

HORNER

HORNER OEE Solution Manual de usuario

Hammerhead

Hammerhead HG375 Manual de usuario

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instrucciones de uso

ABB

ABB HT566657 Manual de usuario

Webasto

Webasto GSE CAN Manual de usuario