3Com iCV-01a Manual de usuario
WebCAM
User Manual
Version 4.0
For models:
iCV-01a / iCV-03a / iCV-08
CONTENTS
Chapter 1: Introduction ________________________________________ 1
Section 1. Features___________________________________________ 1
Section 2. WebCAM as a Remote Surveillance System ______________ 1
Section 3. Package Contents ___________________________________ 2
Chapter 2: Hardware Installation ________________________________ 4
Chapter 3: Web Interface_______________________________________ 5
Section 1. Introduction ________________________________________ 5
Section 2. Using the Web Interface ______________________________ 6
2.1 To View Video ____________________________________________ 7
2.2 Information _____________________________________________ 12
2.2.1 System Status _________________________________________ 12
2.2.2 Current Connections ____________________________________ 13
2.2.3 Event Log_____________________________________________ 13
2.3 Basic Settings___________________________________________ 15
2.3.1 Camera Settings _______________________________________ 15
2.3.2 Network ______________________________________________ 16
2.3.3 Account Settings _______________________________________ 23
2.4 Advanced Settings _______________________________________ 26
2.4.1 Event Notification_______________________________________ 26
2.4.2 Motion Detection _______________________________________ 30
2.4.3 Image Recording _______________________________________ 33
2.4.4 E-mail / FTP___________________________________________ 34
2.4.5 System Settings________________________________________ 37
2.4.6 Image Server__________________________________________ 40
2.4.7 Language_____________________________________________ 44
2.4.8 About ________________________________________________ 45
Chapter 4: View Images Using PDA / PPC / mobile_________________ 46
Chapter 5: Using the Utility ____________________________________ 48
Section 1. Installation ________________________________________ 48
Section 2. Using the Utility Program_____________________________ 49
2.1 Setup Wizard ___________________________________________ 49
2.2 Launch Mimic ___________________________________________ 53
2.3 IP Configuration _________________________________________ 55
2.3.1 IPAddress___________________________________________ 55
i
2.3.2 Advanced (for password and HTTP configuration)____________ 56
2.5 About__________________________________________________ 58
2.6 Refresh ________________________________________________ 58
Chapter 6: MultiMonitor_______________________________________ 60
Section 1. Installing MultiMonitor _______________________________ 60
Section 2. Using MultiMonitor__________________________________ 60
2.1 Device_________________________________________________ 63
2.2 View __________________________________________________ 74
2.3 System ________________________________________________ 74
2.4 User __________________________________________________ 75
2.5 Help___________________________________________________ 76
2.6 Drag-and-Drop Feature ___________________________________ 77
Appendix A: Router Configuration______________________________ 79
Appendix B: Methods to Update WebCAM Firmware_______________ 97
Appendix C: IP Address, Subnet and Gateway____________________ 98
Appendix D: Glossary _______________________________________ 100
ii
Chapter 1: Introduction
Chapter 1: Introduction
Section 1. Features
WebCAM is a compact stand-alone web-server capable of remote video
surveillance. It can be accessed from anywhere in the world via a standard browser
by entering the IP Address, account and password. Each system can support two
types of USB PC cameras. This can be regular USB camera, or one that has
infra-red built-in or even with Pan-Tilt. The server function allows WebCAM to
stream video images directly to the Internet without having to go through a computer.
WebCAM features a Windows-based software that allows the user to archive
streaming video directly to the viewer’s hard-drive. The same software also allows the
user to monitor multiple cameras on one screen.
Features:
• LCD display.
• Built-in Web Server with 32-Bit RISC CPU
• TWO USB Port for USB PC Camera
• Support USB PC Camera with VIMICRO ZC0301 Plus processor built-in
• Support Pan/Tilt and Infrared USB PC Camera (sold separately)
• 10/100Mbps Fast Ethernet Network Access
• Support Java-Enabled Web Browser
• LCD display shows; IP address, Subnet Mask and Gateway
• Support Up to 30 Remote Viewers for each camera
• Up to 8 User Accounts and Passwords
• 5.3VDC 1A Maximum
• Operating Temperature: 0°C ~ 60°C; Operating Humidity: 10% ~ 90%
• Dimensions: 48mm x 63mm x 21mm
• Weight: 75g
• For Indoor Use. Protective housing required for outdoor use.
• Network Protocol: HTTP, TCP/IP, UDP, SMTP, PPPoE, Dynamic DNS, DNS
Client, SNTP, BOOTP, DHCP, FTP, SNMP
• Resolution available: 640x480 (VGA), 352x288 (CIF), 320x240 (QVGA),
176x144 (QCIF), 160x120 (QQVGA).
• Frame Rate: Up to 15fps in 640x480, Up to 20fps in 320 x 240.
• Motion JPEG video stream.
Section 2. WebCAM as a Remote Surveillance System
Once WebCAM is installed, the user can check any of the connected PC cameras
using a standard web browser. The user can monitor and control these cameras
simply by entering the IP address shown on the LCD into a Browser.
WebCAM - user manual -1-
Chapter 1: Introduction
Fig.1 WebCAM Network Diagram
Section 3. Package Contents
WebCAM package contain the following items;
1. WebCAM server.
2. USB Camera.
3. Quick Installation Guide.
4. Utility CD containing;
a. Utility: to configure IP address, update the firmware, etc.
b. MultiMonitor: to monitor multiple WebCAM cameras.
c. Time Server: Time adjustment utility.
d. Adobe Acrobat 5.0 Reader.
e. WebCAM User Manual, and
f. Camera Windows Driver.
5. Slim Ethernet cable.
6. Power adaptor.
WebCAM - user manual -2-
Chapter 1: Introduction
Fig.2 WebCAM Front and Back view
LED Status Indicators on WebCAM
Light color Signal definition Condition description
Green Power state On: Normal power
Red Error Condition Flashing: Error condition occurred
Orange Logon state On: When there is user logon and
receive the image.
Yellow USB data activity Flashing: When data is being
transmitted / received.
Fig.3 WebCAM Status LED Indicator
Light indicators on WebCAM LAN Port LED
Light color Condition description
Green When On: Internet speed is at 100M
When flashing: Data transmitting/receiving
Yellow On: Internet correspond speed is 10M
Flash: Data transmitting/receiving
Fig.4 WebCAM LAN LED Indicators
Fig.5 WebCAM LCD displayed info
WebCAM - user manual -3-
Chapter 2: Hardware Setup
Chapter 2: Hardware Installation
The following details the hardware installation procedure for WebCAM IP camera.
Step 1:
Connect the PC camera into the USB
port of WebCAM.
Step 2:
Connect the WebCAM to LAN by using
the Ethernet UTP port.
Step 3:
Connect DC power adapter output into
WebCAM socket, and plug the DC
power input into the wall socket
Step 4:
Wait a moment and the LCD will
display the IP Address, Subnet and
Gateway. Use a Browser to log into
WebCAM Web Interface
The icon on the LCD shows that
a USB camera is connected.
The LCD display shows that two USB
cameras are attached to the WebCAM.
WebCAM - user manual -4-
Chapter 3: Web Interface
Chapter 3: Web Interface
Section 1. Introduction
WebCAM is designed to work without having to install any software. All the
necessary functions are built-into the unit.
1. Once you have finished the hardware setup shown in Chapter 2, note down the IP
address shown on the LCD
2. On a PC (located in the same LAN), open a Web Brower (eg.: Internet Explorer,
Netscape, Mozilla Firefox or Opera)
3. Enter the IP Address as shown on the WebCAM LCD display and press ENTER
Fig.6 Enter WebCAM IP address
4. A login screen will appear. Click Apply to login.
Fig.7 WebCAM Login screen
WebCAM - user manual -5-
Chapter 3: Web Interface
Section 2. Using the Web Interface
The WebCAM webpage main menu is divided into two sections. The selection menu
on the left and display menu on the right. The selection menu consists of the
following options:
2.1 View Video
2.2 Information
2.3 Basic Settings
2.4 Advanced Settings
Fig.8 WebCAM Main Menu
When using WebCAM for the first time, check the following settings;
a. Basic Settings Camera Settings Anti Flicker Check that this is set to
the correct lighting frequency. Change this to Outdoor if you intend to point the
camera outside. Click Apply to save the configuration.
b. Manually adjust the camera lens for best results.
WebCAM - user manual -6-
Chapter 3: Web Interface
2.1 To View Video
To view video from the connected camera, click on
either ActiveX or Sun Java. Choose either Camera
Aor Bto view the video.
By default the first USB camera connected to
WebCAM will be Camera A
Note:
ActiveX can only function in Windows platform and a
plug-in has to be installed on the client's computer. I
f
this cannot be installed you will have to use Sun Java
to view the video feed. Users who are not using
Windows based Operating System to view the video
feed by clicking Sun Java.
Using ActiveX Controls:
When using ActiveX for the first time, Windows will ask you to download the ActiveX
Controls.
Click the top bar to download and install the appropriate ActiveX controls.
WebCAM - user manual -7-
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cámara web de 3Com
