2easy DT24 Manual de usuario

DT24 USER MANUAL(EN)

2-Wire Video Intercom System

Read this manual carefully before using the product, and keep it well for future use.

Introduction

The monitor is designed with 4 inch screen, it provides a resolution of 320x240

pixels with high quality image display, and it equipped with a handset to com-

municate. The touch sensitive button makes the operation more easily.

Parts and Function

Microphone Mounting Hook

LCD Screen Handset

MENU Button

Terminal Description

L1,L2:

Bus terminal

SW+,SW-:

Door bell call button

connection port

DIP switches:

Total 3 bits can be

-3-

Handset

Handset Line

Speaker

Front view

Up Button Connection Port

Memo Button

UNLOCK Button Mounting Hook

Down Button

Cancel Button

Monitor Button Handset Line

Back view

configured.

Bit1:

reserve

Bit2:

reserve

Bit3:

to set the video impendance

matching, when the video signal

is not so good, set bit3 to “on”.

L1 L2

DIP

1 2 3

Unit Mounting

Accessory contents:

Accessories include a Bracket, two 4X25 screws (use to fasten the Mounting Bracket),

2 wire connectors (use to connect with Monitor).

Installation steps:

Installation height for indoor monitor usually is 145~160cm(refer to sketch map).

Wire the cable correctly(see the later connection chapter) then hang the Monitor on

the Mounting Bracket firmly.

About Main Menu

• Press CALL button on door station.The monitor rings,and the visitor’s image

will be seen on screen.If nobody answers the call,the screen will turn off in

30 seconds automatically.

-4-

The main menu is your starting point

for using all the applications on your

monitor. You can customize your

main menu to display applications,

logos, and languages.

To open the main menu page, tap

key one time on the monitor.

Basic Operation Instruction

Answering a Door Call

Main Menu

Monitor ...

Manual Monitor

Intercom

User Setup

About

Select Item

• Pick up handset to talk with the visitor, the talking duration time is 90s. To

end the conversation, please hand up the handset. If the system connects

two or more Monitors, pick up any Monitor, the others will be automatically

shut off.

Door Release

During talking state, Press

UNLOCK

button to open the door for the visitor.

Entrance Monitoring

When the monitor is in standby mode, press

MONITOR

button(or select

Mon-

itor ...

item on main menu page), The screen can display the view of outside.

If multi door stations are installed, select

Manual Monitor

item to enter cam-

era switch mode. Select

Camera 1 ...

item, the screen will display the image

from the first door camera.Similarly. Select

Camera 2 ...

item to choose the

second one. Select Camera 3 ... item to choose the third one. Select Camera

4 ...

item to choose the fourth one.

To end the monitoring, please tap

MONITOR

button again.

Intercom Function

Intercom function can be initiated by any monitor when multi monitors are in-

stalled.

When the monitor is in standby mode, pick up handset, the

Intercom

item on

main menu page will be selected, press

button to enter.

Intercom Call:

User in one apartment can call other apartments in the sys-

tem, the namelist will be created automatically by the system. Select a name

on the screen, use

button to move upward / downward to select, then

press

button to dial.

Note:

1. Press "MENU " button again to redial.

2.The user code of each monitor must set different

Inner Call:

If multi Monitors are installed in the same apartment, select Inner

Call, all the other Monitors will ring at the same time, whichever Monitor an-

-5-

swers the call, conversation is started.and the other monitors will stop ringing

the same time.

(Note:the user code of all monitors must be same.)

Direct Call Guard unit:

A Monitor can be assigned as Guard Unit Monitor;

when the Guard Unit Monitor answers the call, conversation with the guard

person is started..

-6-

Intercom

Intercom Call ...

Inner Call ...

Direct Call Guard Unit ...

Exit

Select Item

Basic Setup Instruction

Ring Tone Setting

Select

User Setup

item on main menu

page to enter setup page. Select

Door

Station Call Tone

Intercom Call

Tone

DoorBell Tone

item, There

are 12 pieces ring tones can be select-

ed.use

/ button to select last/next

ring tone, press

button to save

and exit.

Door Station Call Tone:

set the ring

tone calling from outdoor station.

Intercom Tone:

set the ring tone call-

ing from other apartments.

DoorBell Tone:

set the ring tone call-

ing from door bell.

Intercom Call

[ 00 ] Jim. Zhang

[ 01 ]

Calo. Liu

[ 02 ] Jacko. Zhang

[ 03 ] Philips. Chen

[ 04 ] Hebe. Zhang

[ 05 ]

Tony. Li

Exit

Calling

User Setup (1)

Door Station Call Tone ...

Intercom Call Tone ...

DoorBell Tone ...

Clock ...

Exit

Select Item

Door Station Call Tone

Selected: 06

1 Carmen 5 Sonatine

9 Do Re Me

2 Ding Dong

6 Edelweiss

10 Happy Birthday

3 Rain

7 Going Home 11 Jingle Bells

4 For Alice

8 Congratulation

12 Telephone Ring

Cancel

Save&Exit

Last/Next

• The first item is Scene mode selection: Total 4 screen modes can be select-

ed in sequence: Normal, User, Soft and Bright. Please note whenever you

modify Brightness or Colour item, Scene item will be set to User mode

automatically.

• The

Brightness

and

Colour

item is for the image quality setting, adjust the

value to get the best image you like.

Note that all the modifications will be done immediately after the operation.

Press

button to quit the adjust page.

Installation Setting

Enter Installation Setup Page

Step1: Press About button on main menu page to enter about information

Step2: Press UNLOCK button and hold for 2s.

Step3: Input 4 digits number according to the following information.

-7-

Monitor Time Setting

Select

Manual Monitor

item on main

menu page, then select

Monitor

Time Set... item. Use / button to

increase / decrease the value, press

button to confirm and return

last page.

Screen Setting

During monitoring or talking state,

press

button,the

ADJUST

will be displayed.

Use

button to select the adjust-

ment item, use

Memo

button to

change the value.

Monitor Time Select

Current :

01min

Cancel

Save&Exit

Last/Next

Scene

Brightly

Bright

Color

Select Camera ...

Select Item

Exit

Inc

How to set the monitor as a Guard Monitor

A Monitor can be assigned as Guard Unit Monitor; when the Guard Unit Moni-

tor answers the call, conversation with the guard person is started..

The code number of 8004 is used to set the monitor as a guard unit monitor

and 8005 is used to cancel this function.

How to set the monitor panel on

In default mode,when receive a calling,the master and slave monitors will

ring at the same time,and just the master monitor can display the image while

the slave monitors can not.But the settings can be changed,you can set the

master monitor and all the slave monitors to panel on at the same time when

receiving a call, just input the code number of 8006 on each slave monitor.

How to set the unlock parameter

Unlock mode:

There are two unlock modes:

1.power-on- to-unlock type:unlock mode=0(by default)

2.power-off-to-unlock:unlock mode=1.

The code number of 8010 is used to set the unlock mode to 0

The code number of 8011 is used to set the unlock mode to 1

Unlock time:

The unlock time can be changed by yourself at any time.it can be set from 1 to

9 seconds.

The code number from 8021 to 8029 are used to set the unlock time to 1~ 9

seconds.

-8-

Step1

Main Menu

Monitor ...

Manual Monitor

Intercom

User Setup

About

Select Item

Step2

H/W : ---

S/W:

---

Local addr: ---

Unlock timing:

---

Unlock2 select:

Video standard:

Language: ---

Exit

Step3

Code Number:[0000]

[0010]:Remove remote

[0011]:Add remote

[8000]:Master 0 [8001]~[8003]:Slaver 1~3

[8004]:Guard unit [8005]:Not guard unit

[8006]:Panel on as slaver called [8007]:Panel off

[8010]:Unlock mode 0 [8011]:Unlock mode 1

2 locks control:

The monitor can be set to control 2 locks while you should set the unlock2

item to “on “ state.

The code number of 8015 is used to set the unlock2 off that it can only control

one lock.

The code number of 8014 is used to set the unlock2 on that it can control two

locks.

Note:1. During talking or monitoring state,

UNLOCK button,two unlock icons will be

showed. Use

button to select the

item you want, and press UNLOCK or

MENU button to release the correspond-

ing door,select item to exit.

2. Restore to default operation will not

change the parameters setting.

How to set the slave monitor address

Maximum 4 monitors can be connected in one apartment,one master moni-

tor together with 3 slave monitors, so you should set the address correctly.

(note:must have one monitor to be set as master monitor)

The code of 8000 is used to set the master monitor.

The code of 8001 is used to set the first slave monitor .

The code of 8002 is used to set the second slave monitor .

The code of 8003 is used to set the third slave monitor .

How to set the menu language

The monitor can support multi languages and it is so simple and fast, just in-

put the corresponding language code on monitor.The language code number

are as follows:

8101: English 8107: Portuguese 8113: Russian

8102: French 8108: S-Chinese 8114: Slovakia

8103: Spanish 8109: T-Chinese 8115: Hungry

8104: Italian 8110: Greek 8116: Czech

8105: German 8111: Turkish 8117: Hebrew

8106: Dutch 8112: Polish

-9-

Note:

the monitor can only support 4 languages. English,French,Spanish and

German are default.But you can customize any 4 languages by yourself.

2. we reserve the copyright to add languages without notice to users.

How to set the address for monitor

Each monitor should be assigned an address in the system, total 32 address-

es can be configured, the code number of 8200 to 8231 is used to controlled

the address of 00 to 31. Please refer to the following table.

Input No. User Code Input No.

User Code

Input No.

User Code

8200 Code=0 8211 Code=11 8222 Code=22

8201 Code=1 8212 Code=12 8223 Code=23

8202 Code=2 8213 Code=13 8224 Code=24

8203 Code=3 8214 Code=14 8225 Code=25

8204 Code=4 8215 Code=15 8226 Code=26

8205 Code=5 8216 Code=16 8227 Code=27

8206 Code=6 8217 Code=17 8228 Code=28

8207 Code=7 8218 Code=18 8229 Code=29

8208 Code=8 8219 Code=19 8230 Code=30

8209 Code=9 8220 Code=20 8231 Code=31

8210 Code=10 8221 Code=21

-10-

Tabla de contenidos

Otros manuales de Sistema de intercomunicación de 2easy

Manuales populares de Sistema de intercomunicación de otras marcas

Bticino

Bticino LINEA 3000 Manual de usuario

MSI

MSI MSI-140 Manual de usuario

golmar

golmar Stadio Plus Manual de usuario

CyberData

CyberData 011211 series Manual

Vidos

Vidos duo M1021 Manual de usuario

Vimar

Vimar ELVOX 7539/E Manual de usuario

SSS Siedle

SSS Siedle BTSV 850-03 Manual de usuario

Dahua

Dahua VTO Series Manual de usuario

Elvox

Elvox 5651 Manual de usuario

Videx

Videx VIDEOKIT Series Manual de usuario

Rocom

Rocom Doortello Business FW T2.05W2.04 Manual de usuario

Viking

Viking E-35-EWP Manual de usuario

Safeguard Supply

Safeguard Supply LRA-EX1000 Manual de usuario

SSS Siedle

SSS Siedle BFCV 850 Series Manual de usuario

GRD

GRD MAX V2 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Aiphone

Aiphone IE-8MD Manual de usuario

Perel

Perel EDB4 Manual de usuario